Résumé du contenu de la page N° 1
OWNER’S MANUAL
Tabletop Heater
Safety First!
Read and become familiar
with this entire manual.
C US
1-888-775-1330
Distributed by:
RTA International
Please retain this manual for reference
Youngtown, AZ 85363
Résumé du contenu de la page N° 2
OWNER’S MANUAL TABLE OF CONTENTS Read These Safety Instructions......................................... 1 Contents Breakdown.......................................................... 2 Screw Packing List............................................................. 3 Assembly Procedure.......................................................... 3 Assembly.......................................................................... 4 Safety First............................................
Résumé du contenu de la page N° 3
OWNER’S MANUAL READ THESE SAFETY INSTRUCTIONS If you smell gas: Shut off gas to the appliance. Extinguish any open flame. Open lid. If odor continues,immediately call your Gas supplier or your life Department. WARNING Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily injury,, death or property damage. ATTENTION Only to be used outdoors. Warning:. Accessible parts may be very hot Keep young children away. Turn off the gas s
Résumé du contenu de la page N° 4
OWNER’S MANUAL CONTENTS BREAKDOWN 2
Résumé du contenu de la page N° 5
OWNER’S MANUAL Item Item Item Qty. Item Qty. No. No. 1 M6 Castle nut 3 11 Burner 1 2 Reflector 1 12 3/16" bolt 4 3 Ø6mm Washer 3 13 M5×10mm bolt 1 4 Emitter screen 1 14 Tank Housing 1 5 Guard 1 15 Igniter button 1 6 Door Plate 1 16 Control knob 1 7 Base 1 17 Handle 1 8 Cast Iron 1 18 Regulator 1 9 M6×15mm bolt 4 19 60mm pin 3 10 3/16" bolt 4 20 M6 flange nut 3 SCREW PACKAGING LIST Item Qty. Item Qty. M6 Castle nut 3 M5×10mm bolt & M5 nut 1 Ø6mm Washer 6 60mm pin 3 M6×15mm bolt 4 M6 flange nut 3
Résumé du contenu de la page N° 6
OWNER’S MANUAL ASSEMBLY STEP 1 STEP 2 2-1. Use 4pcs M6X15mm bolts 1-1. Take out all the parts of to fix the tank housing to the the tabletop Heater. base & cast iron. 1-2. Aim the cast iron at the 2-2. Tighten the bolts as holes on the base. above show. STEP 3 STEP 4 3-1. Put the burner on the tank housing then fix them with 4-1. Fix the regulator to the 4pcs 3/16” bolts. tank housing with the M5X10mm bolt & M5 nut. 4
Résumé du contenu de la page N° 7
OWNER’S MANUAL STEP 5 STEP 6 5-1. Fix 3pcs pins of 60mm length to the emitter screen with 3pcs M6 flange nuts then tighten them. 6-1. Put the emitter screen on the burner. 6-2. Use 4pcs 3/16” bolts to connect the emitter screen to the burner. Tighten the bolts. STEP 8 STEP 7 7-1. Put the guard on the burner through the emitter 8-1. Put 3pcs washers on each screen. pins of the 60mm length. 7-2. Put the ends of the guard into the holes of the burner. 5
Résumé du contenu de la page N° 8
OWNER’S MANUAL STEP 9 STEP 10 10-1. Fasten the reflector with 3pcs M6 Castle nuts. 9-1. Put the reflector through the pins and on the washers. STEP 11 STEP 12 11-1. Turn off the control knob of the burner. 11-2. Fix the 1.02Lbs gas tank (not included) to the regulator (rotate the gas tank clockwise 12-1. Close the door plate and toward the regulator until lock it with the handle (rotate tighten it). the handle 90 degree). 6
Résumé du contenu de la page N° 9
OWNER’S MANUAL SAFETY FIRST Read and become familiar with this entire manual, especially the following precautions . Caution: this appliance is for outdoor use only(outside any enclosure) Always make sure there is fresh air ventilation. Use only outdoors in a well-ventilated space, never use in a building, garage or any other enclosed area. Always maintain at least 18“clearance(top)and 24”clearance (side) from combustible materials. Always place heater on a hard and level surface. Do not
Résumé du contenu de la page N° 10
OWNER’S MANUAL TABLETOP HEATER LOCATION ● The tabletop heater is primarily for outdoor use only. Always ensure that adequate fresh air ventilation is provided. ● Always maintain proper clearance to combustible materials, i.e. top 45 cm(18”) and sides 60 cm(24”) minimum. ● Tabletop heater must be located on a stable and strong table. ● Never operate heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored. CHECKING FOR LEAKS Make 1-2 oz. of le
Résumé du contenu de la page N° 11
LO LO OWNER’S MANUAL Heater is on a hard and level surface. There are no signs of spider or insect nests. All burner passages are clear. All air circulation passages clear. Children, pets, clothing, flammable materials and items that can be damaged from radiant heat are away from the heater. Children and adults in the area have been alerted to the high temperature hazards: especially burns and clothing fires. Children and adults in the area have been warned not to touch heater near
Résumé du contenu de la page N° 12
OWNER’S MANUAL Lighting 1. Turn Gas control knob to “Off” position. 2. Push in and rotate the Control Knob to“Pilot”position. Depress igniter button. 3. Once burner is lit, hold Control Knob in for at least 30 seconds and release. 4. If burner does not stay lit, turn to“Off” position and wait 5 minutes and repeat 2 and 3. 5. Once burner is lit, rotate Knob to desired heating level (LO: low ; HI: high). If you experience any ignition problem, turn off the heater and gas supply, and consult “Troub
Résumé du contenu de la page N° 13
OWNER’S MANUAL AFTER OPERATING Gas control is in OFF position. Disconnect Gas line. Heater is upright in a secure location. MAINTENANCE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Inspect the visible portion of the hose before each use of the appliance. Inspect the entire hose assembly at least annually. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways cle
Résumé du contenu de la page N° 14
OWNER’S MANUAL TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION Pilot will not light Tank fuel empty Replace LPG tank Opening blocked Clean or replace opening Air in supply system Purge air from lines Loose connections Check all fittings Pilot will not stay on Debris around pilot Clean dirty area Loose connections Tighten connections Thermocouple bad Replace thermocouple Gas leak in line Check connections Lack of fuel pressure Tank near empty. Replace LPG tank. Burner will not light Pressure is l
