Instruction d'utilisation Harbor Freight Tools 93119

Résumé du contenu de la page N° 1

2-1/2 GALLON PAINT POT
93119
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INjURY ,
REAd ANd UNdERSTANd ALL WARNINGS
ANd INSTRUCTIONS BEFORE USE.
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools.
For technical que

Résumé du contenu de la page N° 2

Specifications Maximum Pressure 80 PSI Air Inlet 1/4” NPT Working Pressure 30-60 PSI Net Weight 20.5 lb. 3 1 Tank Capacity 2.5 gallons Dimensions 9 / ” Diameter x 18 / ” 4 2 Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for f

Résumé du contenu de la page N° 3

air passages. Wear an ANSI-approved dust mask or respirator when working around chemical mist. 9. do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 10. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool hoses periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept clean, dry, and fr

Résumé du contenu de la page N° 4

22. do not discard or make any alterations to the safety valve. Tampering with, welding or drilling the pot can weaken it. 23. CAUTION: Do not use abrasive, corrosive or rust inducing materials with this pot. It is not designed for those materials. To use them can damage the pot’s internal parts. 24. Industrial applications must follow OSHA requirements. 25. Read all information concerning coating products and cleaning solvents. Chlori- nated solvents, such as 1-1-1 Trichloroethane and Met

Résumé du contenu de la page N° 5

Operation Efficient and easy use of the pressurized pot depends on the careful performance of the steps required to prepare the pot for use, to fill the pot, and to operate the pot. Preparing the Pot for Use 1. Follow the manufacturer’s directions when mixing and preparing the paint or coating. 2. Strain the paint using a fine mesh screen to keep foreign matter and lumps from clog- ging the pot’s passageways. NOTE: Before using, it is recommended that the air supply line be passed through a f

Résumé du contenu de la page N° 6

WARNING: Always make sure that the equipment connected to the pot or hose outlet has a higher pressure rating than the regulated air pres- sure in the pot. Operating the Pot 1. Turn ON the air supply at the recommended PSI range (30-60 PSI). 2. Adjust the paint pressure by turning the T-handle adjusting screw (on regulator) clockwise to increase pressure and counterclockwise to decrease the pressure. 3. Adjust the atomization air for the spray by using the regulator on the pot. 4. Operate the

Résumé du contenu de la page N° 7

Troubleshooting In the event the pot is not operating properly, refer to the following table for troubleshooting procedures. Problem Possible Cause Possible Solution Air escapes from the port on A broken or damaged dia- Replace the diaphragm. the regulator cap. phragm. Pressure drops slowly on the A dirty or worn valve seat in Clean or replace the valve gauge. the regulator. seat. Mix or thin the paint according Paint tends to settle in can Insufficient mixing of the to the manufacturer’s in

Résumé du contenu de la page N° 8

Parts List Part description Qty Part description Qty 1 Tank Shell Assembly 1 10 Handle 1 2 Lid Gasket 1 11 Hex Nut 1 3 Lid Assembly 1 12 Street Elbow 1 4 Adapter 3 13 Thumb Screw 4 5 Gauge 1 14 Yoke Assembly 4 6 Regulator 1 15 Cotter Pin 4 7 Swivel Adapter 1 16 Hinge Pin 4 8 Branch Tree 1 17 Fluid Tube 1 9 Safety Valve 1 18 Fluid Outlet Adapter 1 Assembly diagram SKU 93119 For technical questions, please call 1-800-444-3353. Page 8