Résumé du contenu de la page N° 1
ATD-8401
40 LBS. PRESSURE BLASTER
INSTRUCTION MANUAL
ATD abrasive blasting equipment is designed for cleaning and removing rust, scale, paint and
dirt. It is the ideal method for stripping, polishing and etching projects. This equipment can
be used with abrasive powders and liquids. This model is equipped with the standard use
ceramic nozzle.
SAFETY WARNING & CAUTIONS:
WARNING: Airborne dust: This is one of the most serious hazards associated with blasting
operations. When ev
Résumé du contenu de la page N° 2
WARNING: When using pneumatic equipment, basic safety precautions should always be followed to reduce the risk of personal injury and hazards due to over pressurization. WARNING: Some dust created by abrasive blasting, grinding, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Your risk from exposure varies, depending on how often you do this work. To reduce your exposure to these chemicals
Résumé du contenu de la page N° 3
10. Make sure the air pressure adjustment is set at “0 PSI” and the shut off valve is in the off position when not in use and before attaching the air compressor. 11. Do not operate the unit when tired or under the influence of alcohol or drugs. 12. Before using check for alignment and binding of moving parts, any broken parts or mounting fixtures and any other conditions that may affect proper operation. Do not use the unit if any switch does not turn on or off properly. 13. When se
Résumé du contenu de la page N° 4
4. Attach the other wheel (#16) to the axle (#25) using the remaining cotter pin (#14). 5. Slide the handle bar (#6) onto the left leg (#7) and the right leg (#17) and secure it with two self-tapping screws. 6. Slide the two end caps (#18) over the ends of the legs (# 7 & # 17) Abrasive Metering Valve and Abrasive Gun Assembly (Refer to Fig 2): 1. Attach the abrasive metering valve (#26) to the side hole of the intake manifold (#12). Attach one of the elbow c
Résumé du contenu de la page N° 5
Air Pressure Adjuster and Safety Valve Assembly (Refer to Fig 3): Use PTFE tape on all air fitting threads. 1. Attach the connector (#8) to one of the side inlets of the air pressure adjuster (#9). Attach the intake manifold (#12) to the other side of the nipple connector (#11). Make sure the pressure gauge on the air pressure adjuster and the front inlet of the intake manifold face the same direction, as in figure 3. 2. Attach the joint pipe (#10) to the front intake of the inta
Résumé du contenu de la page N° 6
OPERATION: WARNING: Always wear your hood, dust mask and heavy-duty canvas gloves when operating. 1. Close the abrasive metering valve (#26), pour about 25 lbs of abrasive medium into the tank. Then close the tank filler cap (#4) securely, assuring that o-ring (#3) is in place. 2. Turn the air pressure adjuster (#9) counter-clockwise (lowest pressure) fully. With the air compressor off, attach the connector (#8) to an air supply hose coming from the air compressor.
Résumé du contenu de la page N° 7
AIR/ABRASIVE SUPPLY REQUIREMENTS Hose ID Hose Length Nozzle ID Compressor HP CFM @125PSI ABRASIVE USE PER HOUR 3/8” 50ft 0.076” 2 6 30lbs 3/8” 25ft 0.098” 4 12 80lbs 1/2” 50ft 0.118” 7 20 120lbs 1/2” 25ft 0.132” 10 25 150lbs We recommend that air pressure in the range of 65-125PSI will provide the best results MAINTENANCE: 1. Keep your pressure blaster clean and protect from damage. 2. Depressurize after using. 3. When initially pressurizing, check for leaks at the tank top and
Résumé du contenu de la page N° 8
SAFETY AND HEALTH CONSIDERATIONS Before opening tank be sure that it is not pressurized. Be sure that the gauge reads”0 PSI”. Depressurize the tank before opening it by exhausting pressure through the abrasive gun (#24). Disconnect the air compressor before opening tank. Protect yourself and those around you from “overspray”. Remember that your portable abrasive blaster is shooting a powerful spray of abrasive material. Do not point it at yourself or anyone around you. Wear a filter
Résumé du contenu de la page N° 9
TROUBLESHOOTING PROBLEM REMEDY Surging of blast flow? Air pressure too low See “Lack of Air” Too much media Adjust media valve Excessive media consumption? Media valve open too far Close slightly Air pressure too low Check pressure gauge Clogging and plugging of blast flow? Debris in media Purge & Screen Media size too large Use smaller grit size Nozzle plugs Use large nozzle or Adjust media valve Wet media Dry media, drain water from air Moisture in abrasive media? Wet media
Résumé du contenu de la page N° 10
Résumé du contenu de la page N° 11
ITEM# ORDERING PART# PART DESCRIPTION 01 PRT8401-01 HOOD 02 PRT8401-02 SCREW 03 PRT8401-03 O-RING 04 PRT8401-04 TANK FILLER CAP 05 PRT8401-05 SAFETY VALVE 06 PRT8401-06 HANDLE BAR 07 PRT8401-07 LEFT LEG 08 PRT8401-08 CONNECTOR 09 PRT8401-09 AIR PRESSURE ADJUSTER 10 PRT8401-10 JOINT PIPE 11 PRT8401-11 NIPPLE CONNECTOR 12 PRT8401-12 INTAKE MANIFOLD 13 PRT8401-13 ELBOW CONNECTOR 14 PRT8401-14 COTTER PIN 15 PRT8401-15 TANK 16 PRT5200-21 WHEEL 17 PRT8401-17 RIGHT LEG 18 PRT8401-18 L
