Résumé du contenu de la page N° 1
MOW’N MACHINE
15 cu. ft. Metal Grasscatcher
For F-Series
Power Units
Tested. Proven. Unbeatable.
SAVE THIS
MANUAL!
Include it with
your Mow'n Machine
Manual. It contains
repair part information
not found in other
manuals.
MAN0115
Rev. 8/17/2007
INSTALLATION MANUAL
Résumé du contenu de la page N° 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with the Operator’s Manual. The customer must sign the registration which certifies that all Dealer Check List items have been complete
Résumé du contenu de la page N° 3
HOPPER ASSEMBLY Assembly of hopper will be easier if assembled upside ASSEMBLE HOPPER down on a flat surface, see Figure 2. Note that Figure 1 shows hopper in the upright position. ! LEA EL INSTRUCTIVO! NOTE: When assembling the hopper, make sure bolts that will interfere with grass clippings are installed with Si no lee Ingles, pida ayuda a alguien que si lo lea para que le heads on the inside. This will prevent clippings from traduzca las medidas de seguridad. catching on bolts when the grass
Résumé du contenu de la page N° 4
2. Make sure two pivot bearings (13), (Figure 4) are INSTALL CROSSMEMBERS attached to the inside of front cross channel (15) using sheet metal screws (14). Do not tighten at this time. 3. Slide left side door trip lever (17) through opening on left side panel, pivot bearings (13) attached to Front Crossmember front cross channel (15), and right side panel. 4. Secure front cross channel (15) to bottom panel using whiz bolts (4) and whiz nuts (5). Tighten sheet metal screws. 5. Attach right dump l
Résumé du contenu de la page N° 5
5. Torque all hardware according to page 8. 2. Attach latch linkage rod (36) to both right and left door handle mount. Be sure to install spring bracket (35) into clevis when attaching left side (see Figure 7). 3. Attach opposite end of door linkage rod (45) to door handle mount. 4. Adjust linkage so that there is a slight amount of pressure holding the door closed when handle is snapped over center. 5. Attach opposite end of latch linkage rod to door latches. 6. Attach spring (34) to hole in
Résumé du contenu de la page N° 6
5. Install rubber bumpers (19). Secure with flange lock nuts (13). 48 40 5 1 9 45 8 49 7 50 19 13 28 2 42 36 39 40 41 40 44 4 5 6 7 4. 70067 1/4 NC x 1/2 Whiz bolt 5. 70065 1/4 NC Whiz nut 28. 70538 Latch bracket 36. 70547 Linkage latch rod 1. 74082 Right hopper support 39. 70024 Clevis pin 2. 74083 Left hopper support 40. 1326 Cotter pin, 1/8 x 1/2 5. 74084 Cross brace 41. 4378 5/16 Flat washer 6. 920 3/8 NC x 1-3/4 Cap screw GR5 42. 70543 Latch pivot bracket 7. 15030 3/8 NC Flanged lock nut 44
Résumé du contenu de la page N° 7
Align hinges of rear crossmember (12) on hopper with INSTALL REAR HOPPER SUPPORT & hinges of rear hopper pivot (4). Insert clevis pins (14) REAR HOPPER PIVOT and hair pins (15) as shown in Figure 12. 1. Attach rear hopper support (3) to the rear of the ATTACH CABLE power unit using four flanged head cap screws (8), standard flat washers (9), and two flange lock nuts 1. Attach cable (10) to rear of power unit on both right (7) as shown in Figure 11. and left sides as shown in Figure 13. NOTE: R
Résumé du contenu de la page N° 8
3. Tilt hopper assembly back. SECURE HOPPER 1. Rotate hopper onto right and left hopper supports. NOTICE 2. Insert 3/8 lynch pins (18) to attach front hopper ■ Do not attempt to tilt hopper to service position crossmember to support brace as shown in Figure unless hopper is completely empty. Failure to 14. empty hopper could result in damage to hopper. 4. On power unit, unhook rubber latches and lift hood assembly to service position. 5. Secure with prop rod. 18 18. 33000 3/8 x 2-1/4 Lynch pins
Résumé du contenu de la page N° 9
MOUNT ASSEMBLY REF PARTS QTY DESCRIPTION REF PARTS QTY DESCRIPTION 1 74082 1 Right hopper support 11 4528 4 5/16 NC x 1-3/4 Cap screw GR5 2 74083 1 Left hopper support 12 6778 4 5/16 NC Lock nut 3 73677 1 Rear hopper support 13 14139 2 5/16 NC Flange lock nut 4 73678 1 Rear hopper pivot 14 63523 2 3/4 x 4-1/2 Clevis pin 5 74084 1 Hopper cross brace 15 2688 2 5/32 Hair pin cotter 6 920 4 3/8 NC x 1-3/4 Cap screw GR5 16 70068 2 1/4 x 3/4 Whiz bolt 7 15030 12 3/8 NC Flange lock nut 17 70065 2 1/4 W
Résumé du contenu de la page N° 10
HOPPER ASSEMBLY 10 Parts MAN0115 (Rev. 3/31/2006)
Résumé du contenu de la page N° 11
HOPPER ASSEMBLY PART LIST REF PARTS QTY DESCRIPTION REF PARTS QTY DESCRIPTION 1 70521 1 Hopper top 28 70538 2 Latch bracket 2 70504 1 Window 29 70526 1 Hopper handle 3 70505 2 Mounting bracket 30 70527 1 Handle grip, .812 x 4 4 70067 68 1/4 NC x 1/2 Whiz bolt 31 1686 2 3/8 NC x 3/4 HHCS 5 70065 82 1/4 NC Whiz nut 32 15030 2 3/8 NC Flange lock nut 6 1000664 1 Right side panel 33 70546 1 Link, .19 x .75 x 4.0 7 1000665 1 Left side panel 34 70834 1 Spring 8 70528 1 Upper front panel 35 1001501 1 Sp
Résumé du contenu de la page N° 12
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
Résumé du contenu de la page N° 13
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN 1 2 7 34 5 6 MM 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG.............................................................Agriculture NC ....................................................National Coarse ATF...............................Automatic Transmission Fluid NF.....
Résumé du contenu de la page N° 14
LIMITED WARRANTY TM (Mow’n Machine Zero-Turn Mower and TM Woods Boundary Utility Vehicle Replacement Parts) TM Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine zero-turn TM mowers and attachments and Woods Boundary utility vehicles, accessories and attachments to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser. IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FO
Résumé du contenu de la page N° 15
LIMITED WARRANTY TM TM (Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles) Please Enter Information Below and Save For Future Reference. Date Purchased: __________________________ From (Dealer): _____________________________________ Model Number: __________________________ Serial Number: _____________________________________ WHAT IS COVERED: TM TM Woods Equipment Company (“WOODS”) warrants Mow’n Machine zero-turn mowers and attachments and Woods Boundary utility vehicles, acces
Résumé du contenu de la page N° 16
PART NO. MAN0115 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 800-319-6637 tel 800-399-6637 fax www.WoodsEquipment.com © 2001 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holde
