Résumé du contenu de la page N° 1
CRW4261t
SERIES
User Guide
Guide de I’utilisateur
Bedienungsanleitung
Résumé du contenu de la page N° 2
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Systems Technology, Inc. Address: 100 Century Center Court San Jose, California 95112 Telephone: (408) 467-2330 FAX: (408) 437-8791 Type of Equipment: CD Recorder Model Name: CRW4261t CRW4261t-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference rec
Résumé du contenu de la page N° 3
Laser Diode Properties CAUTION Material : GaAlAs Use of controls or adjustments or performance of Wavelength : 780-790 nm procedures other than those specified herein may Emission Duration : Continuous result in hazardous radiation exposure. Laser Output Power : Less than 44.6 m W* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 This compact disc player is classified as a CLASS 1 CLASS 1 LASER PRODUCT LA
Résumé du contenu de la page N° 4
WARNING WARNING ¢ WARNING ¢ • The temperature where CRW4261t is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CRW4261t cover to reduce the risk of electric shock. • Always remove the disc before transporting CRW4261t. i
Résumé du contenu de la page N° 5
Important Precautions Important Precautions Please read the following precautions before attempting to operate the CRW4261t. • Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unusable disc. • Always record in a dust-free environment. If the disc must be removed from the CRW4261t before record- ing is finished, store the disc in a clean, dust-free environment. • The C
Résumé du contenu de la page N° 6
Table of Contents Table of Contents Introduction ...............................................................................1 CRW4261t Features ........................................................1 Orange Book Compatible Recording ..............................2 Chapter 1 - System Configuration ......................................3 Computer .........................................................................3 Software ............................................
Résumé du contenu de la page N° 7
Introduction Introduction Thank you for purchasing a Yamaha CRW4261t drive. Please read this manual before using the drive in order to make the best use of the superior CRW4261t functions. After reading, please retain this manual for future reference. CRW4261t Features n 2xS Recording (Rewritable) - 4xS Recording (Recordable) - 6xS Reading The CRW4261t is able to write (overwrite) CD-RW discs at double speed, and is able to write CD-R discs at quad speed, double speed, or n
Résumé du contenu de la page N° 8
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD- ROM drives other than a CD-RW or a CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not p
Résumé du contenu de la page N° 9
Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW4261t, make sure that you have all of the items on the list of included items. In order to use the CRW4261t, you will require the following. Computer The following operating environment is required: • An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU (in order to write at 4x speed), or a 100 MHz or faster 486 CPU (in order to write at 2x speed) • A vacant IDE interface connec
Résumé du contenu de la page N° 10
Chapter 1 - System Configuration Discs On the CRW4261t, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and 3 (Orange Book). Yamaha recommends the following Yamaha CD-RW and CD-R discs: CD-RW Discs > CRWM74R (f 120mm, 74 minutes) CD-R Discs > CDM12Y74M (f 120mm, 74 minutes) > CDM12Y74T (f 120mm, 74 minutes) Read-only Discs You can use discs with the logo which conform to the Compact Disc Read Only Memory standard (CD-R
Résumé du contenu de la page N° 11
Chapter 2 - Installing the Yamaha CRW4261t Drive Chapter 2 - Installing the Yamaha CRW4261t Drive MASTER/SLAVE settings Before you install the CRW4261t in your computer, you must make the MASTER/SLAVE setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW4261t drive. Important: When the unit is shipped from the factory, this setting is in the MASTER position. Note: Use long-nose pliers to remove or insert the jumper pin.
Résumé du contenu de la page N° 12
Chapter 2 - Installing the Yamaha CRW4261t Drive Setting the CRW4261t as the MASTER As shown in the diagram at the right, insert the CSEL SLAVE jumper pin into the right edge of the jumper MASTER switch. Note: If only the CRW4261t will be connected to the IDE interface connector, connect the CRW4261t to the end of the connector. Setting the CRW4261t as the SLAVE As shown in the diagram at the right, insert the CSEL SLAVE jumper pin into the middle of the jumper MASTER switch. CS
Résumé du contenu de la page N° 13
OFF Chapter 2 - Installing the Yamaha CRW4261t Drive Installing the CRW4261t drive The following steps will differ slightly depending on the type of com- puter you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. 1. Switch off your computer, and unplug it from the AC outlet. If you fail to do this, there is a danger of electric shock and/or of causing short circuits, which may damage th
Résumé du contenu de la page N° 14
Chapter 2 - Installing the Yamaha CRW4261t Drive 3. Your hands or body may be holding a charge of static elec- tricity. Touch a metallic portion of the chassis or power supply to release any such charge. 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Slide the CRW4261t drive into the drive bay from the front. At this time, be careful not to apply excessive force to the drive itself. Finger-tighten the four fastening scre
Résumé du contenu de la page N° 15
Chapter 2 - Installing the Yamaha CRW4261t Drive 6. Connect the IDE interface connector. Connect the 40-pin IDE interface connector to the IDE interface located on the rear panel of the CRW4261t drive. Position the connector so that the colored line is at pin 1 (your lower right). 7. Connect the AUDIO cable. Connect the single 4-pin connector (Sound Blaster compatible) to the sound card. Connect the 4-pin connector at the other end of the cable (the larger connector) to the AUDIO OUT c
Résumé du contenu de la page N° 16
Chapter 2 - Installing the Yamaha CRW4261t Drive AUDIO cable To the CRW4261t 4-pin connector (large) To the CDR100/102 (3-pin connector) * Simultaneous use with the CRW4261t is is not possible. To the Sound Card (Sound Blaster compatible) 4-pin connector (small) 8. Connect the power supply cable. Connect the +12V and +5V 4-pin power cable to the power supply interface located on the rear panel of the CRW4261t drive. The shape of the connector makes it impossible to reverse the connec- tion
Résumé du contenu de la page N° 17
Chapter 2 - Installing the Yamaha CRW4261t Drive 9. Tighten the four fastening screws securely. 10. Attach the cover of your computer. 11. Connect the power cable to an AC outlet, and switch on your computer. Make sure that the LED located on the panel of the CRW4261t drive is lit. 12. Start up your operating system. For the procedure, refer to the manual for your operation system. 13. Install the writing software. For the installation procedure, refer to the manual for your writing soft- ware
Résumé du contenu de la page N° 18
Chapter 3 - Operation Chapter 3 - Operation Front Panel 1 76 2 3 45 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level. 4 ON/DISC LED This indicator lights up in orange when the CRW4261t is powered on, and
Résumé du contenu de la page N° 19
Chapter 3 - Operation 6 Eject button This button is used to open or close the tray. 7 Manual Eject hole This is used to manually eject a disc that cannot be ejected in the nor- mal way. It is for emergency use only. Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. 13
Résumé du contenu de la page N° 20
Chapter 3 - Operation Ejecting the Disc If the CRW4261t is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the ATAPI command prohibits the eject operation while the CRW4261t is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) Press the eject button If the CRW4261t is not powered on: Pressing the eject button will not eject th
