Résumé du contenu de la page N° 1
OWNER'S MANUAL
JBOS-5 Benchtop Oscillating Spindle
Sander
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.jettools.com e-mail jet@jettools.com M-708404 10/00
Résumé du contenu de la page N° 2
Important Information 2-YEAR JET offers a two-year limited LIMITED WARRANTY warranty on this product REPLACEMENT PARTS Replacement parts for this tool are available directly from JET Equipment & Tools. To place an order, call 1-800-274-6848. Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Part number listed within this manual 4. Shipping address other than a Post Office box. REPLACEMENT PART WARRANTY JET Equipment & Tools makes ever
Résumé du contenu de la page N° 3
WARNING 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this tool until proper training and knowledge has been obtained. 2. Keep guards in place and in working order. 3. Keep fingers and hands away from the spindle while in operation. Avoid getting fingers too close to the drum. 4. Remove adjusting keys and wrenches. Form habit of checking to see that keys and adjusting wrenches are removed before operating. 5. Keep work area clean.
Résumé du contenu de la page N° 4
Table of Contents Page Warranty..................................................................................................................................................2 Warnings .................................................................................................................................................3 Table of Contents.....................................................................................................................................4 Specification
Résumé du contenu de la page N° 5
Unpacking and Clean-Up Insert Plates 1. Always use an insert plate. 1. Finish removing all contents from the shipping container. Do not discard any 2. There are 2 oblong, and 2 round insert plates included with the machine. The oblong insert shipping material until the sander is set up plates are used when the table is tilted for and running properly. bevel sanding. Each plate has a notch on the outer edge to ensure that it is inserted properly 2. Report damage, if any, to your local distributor
Résumé du contenu de la page N° 6
Setup for 90° 1. Loosen both knobs, (A, Fig. 3) and place the table in the 0° position. 2. Place a square (B, Fig. 3) on the table. Rest the long section of the square against the sanding drum. The square should be flat agianst the table and the sanding drum. 3. If the table needs adjustment loosen both knobs and tilt the table so thast the square is flat against the table and sanding drum. 4. Make sure the pointer (C, Fig. 3) reads 0°. If the pointer needs adjusted loosen the screw (D, Fig. 3),
Résumé du contenu de la page N° 7
Removing Spindles Using the provided wrenches, loosen the spindle nut (A, Fig. 5) clockwise while holding the spindle housing flat (B, Fig. 5) with the other wrench. Changing Sanding Sleeves 1/4", 1/2" and 5/8” 1. Loosen the clamp (A, Fig. 6) with a cross point screwdriver. 2. Remove the sanding sleeve from the spindle shaft. 1-1/2” and 2” (optional 3”) 1. Loosen the nut (B, Fig. 6) with the provided wrench. 2. Remove the sanding sleeve from the spindle shaft. 3. Reverse these steps to install t
Résumé du contenu de la page N° 8
Table Assembly for the JBOS-5 8
Résumé du contenu de la page N° 9
Base & Motor Assembly for the JBOS-5 9
Résumé du contenu de la page N° 10
Parts List for the JBOS-5 Index Part No. No. Description Size Qty. 1..........6286914W........................ Base.............................................................. .................................1 2..........6286891........................... Top Plate....................................................... .................................1 3..........JBOS5-03 ........................ On/Off Switch ................................................ .................................
Résumé du contenu de la page N° 11
Index Part No. No. Description Size Qty. 53........JBOS5-53 ........................ Support Trunnion-Right.................................. .................................1 54........JBOS5-54 ........................ Support Trunnion-Left.................................... .................................1 55........JBOS5-55 ........................ JET Lock Knob.............................................. M6x15 ......................2 56........JBOS5-56 ........................ Hex Sock
Résumé du contenu de la page N° 12
575807 .........................1/2" ....................80 Grit 575808 .........................1/2" ..................100 Grit 575809 .........................1/2” ..................120 Grit 575810 .........................5/8” ....................60 Grit 575811 .........................5/8” ....................80 Grit 575812 .........................5/8” ..................100 Grit 575813 .........................5/8” ..................120 Grit 575838 .........................1-1/2” ..........
