Instruction d'utilisation Vision Fitness X6200HRC/DA

Résumé du contenu de la page N° 1

VISION FITNESS
Assembly
Guide
MODELS X6200HRC/DA & X6000DA
DUAL-ACTION ELLIPTICAL TRAINERS

Résumé du contenu de la page N° 2

Before you begin… To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding though, enter your new Elliptical Trainer’s serial number here: Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

Résumé du contenu de la page N° 3

TOOLS & HARDWARE INCLUDED MM 5 Allen Wrench BLUE BAG MM 13 Wrench Screwdriver MM M8 x 45 Bolt Quantity: 2 MM M8 x 80 Bolt Quantity: 4 MM M8 x 13 Nylock Nut MM Quantity: 4 5 L-Shaped Wrench MM MM BLACK BAG 19 D x 440 L Rear Folding Axle Quantity: 1 (not shown to scale) MM M8 x 16 Bolt 3 Quantity: 4

Résumé du contenu de la page N° 4

ORANGE BAG PINK BAG 8 x 17 X 1.5T Washer Quantity: 2 MM M8 x 16 Bolt 16 x 22 x .3T Spring Washer Quantity: 2 Quantity: 2 8 x 15 X 2T Lock Washer Quantity: 4 MM MM 16 x 28 x 1.5T Washer 5/16” x 30 x 1.5T Washer M8 x 60 Bolt M5 x 25 Bolt Quantity: 2 Quantity: 2 Quantity: 2 Quantity: 1 GREEN BAG MM MM M7 x 35 Bolt M8 x 12 Bolt Quantity: 2 Quantity: 2 MM MM M8 x 25 x 1.5T Washer M16 x 22 x .3T Spring Washer M8 x 13 Nylock Nut M8 x 12 Bolt Quantity: 2 Quantity: 2 Quantity: 4 Quantity: 2 MM 13 Nut Cap

Résumé du contenu de la page N° 5

STEP 1 STEP 1 BLACK BAG • Install the left and right stabilizers MM with the four bolts (M8 x 16 ), using MM the Blue 5 Allen wrench. • Cover both stabilizers with the included rubber boots. • Insert the rear folding axle shaft MM MM (440 L x19 D) into the rear tube. STEP 2 ORANGE BAG STEP 2 • Slide a spring washer (M16 x .3T) onto the right-hand side of the rear folding axle, followed by the right- hand pedal arm guide rail (the guide rails each have a blue indicator arrow printed on their sid

Résumé du contenu de la page N° 6

STEP 4 STEP 4 PINK BAG • X6000 only: Unfold the RPM sensor wire, located in the frame console mast bracket. Remove any kinks. • All models: Slide the rubber console X6000DA mast cover onto the bottom of console mast, and slide it up as far as it will OR go. • X6000 only: Holding the console mast above the frame bracket, guide the RPM sensor wire and lower magnet cable up through the console mast while simultaneously sliding the console mast onto the frame bracket. X6200HRC/DA • All models: Bol

Résumé du contenu de la page N° 7

STEP 5 GREEN BAG • Slide a large spring washer (M26 x 34 x .3T) onto the console mast axle. Locate and slide the right STEP 5 upper handlebar bracket onto the console mast axle and attach with a MM washer (M8 x 35 x 2T) and 13 MM NyLock nut, using the 13 wrench. MM Snap the plastic 13 nut caps over the nuts. • Slide a small spring washer (M16 x 22 x .3T) onto the lower pedal arm support, followed by the right lower arm. Attach with a washer (M8 x 25 x 1.5T) and bolt (M8 x 12), MM using the Bl