Résumé du contenu de la page N° 1
STAR TRAC
14410 Myford Road
Irvine, CA 926060 USA
WORK INSTRUCTIONS,
E-TBT / E-TBTe INSTALLATION
2 620-7921 Rev A
Résumé du contenu de la page N° 2
GENERAL Before using this product, it is essential to read ALL installation Instructions and this ENTIRE operations manual; the manual describes equipment setup and instructs members on how to use it correctly and safely. TOOLS REQUIRED 1. Phillips screwdriver, #2 (Included) 2. Hex (Allen) key, 3/16 (Included) 3. Hex (Allen) key, 16” (Included) 4. Hex (Allen) key, 5MM (Included) 5. Torque wrench (not included) FACTORY CERTIFIED INSTALLER If you are a Factory Certified Installe
Résumé du contenu de la page N° 3
UNPACKING INSTRUCTIONS Step 1. Step 2. Lay the box with heavy end facing down in the Lift and remove the box from the pallet base. area where it is going to be assembled. Cut and remove packaging straps then open and remove the top cover. Step 3. Step 4. Lift the unit off of the pallet base, then remove Open the display assembly box and carefully all packaging materials. remove its content. 4 620-7921 Rev A
Résumé du contenu de la page N° 4
Step 5. Remove remaining packaging ma- terials and lay all components on the floor. 1 Step 6. Verify the following components are included in the package: 1. TBT frame. 2. Display console assembly. 3. Upper neck. 4. Left and right upper body arms. 5. Owner’s manual, installation manual and warranty registra- 5 tion card. 6. Hardware kit. 2 6 4 3 1 2 3 1 2 3 4 5 4 Step 7. Step 8. Verify the following hardware is included in the kit: Verify the following tools are in
Résumé du contenu de la page N° 5
INSTALLATION INSTRUCTIONS Step 1. Step 2. Route display cables up through upper half of Insert the upper half of the neck into the lower neck through the holes provided. half. Caution: Be careful not to pinch any cables between the two sections of the assembled neck. Step 3. Step 4. Install two 5/16” - 18 X 3/4” button head screws Secure the neck by tightening the 3/8-16 x 2” into front neck using a 3/16” hex key. Tighten socket head cap screw using a 5/16” hex key. bolts to 20
Résumé du contenu de la page N° 6
Step 5. Step 6. Using provided screwdriver, remove the M4 x Slide the back of the display with the mounting 0.7 screws that hold the display assembly to- bracket onto the upper neck of the Total Body gether, then separate the back of the display Trainer. from the front. Caution: Be careful not to pinch any cables between the two sections of the assembled neck Note: Retain the screws for later use. Step 7. Step 8. Line up the four holes of the mounting bracket Using provided 5m
Résumé du contenu de la page N° 7
3 2 4 1 Step 9. Step 10. Identify the four cables coming out of the neck Plug-in the 12-pin main I/O cable into the front and mounting bracket: display circuit board at J4 connector. 1. Heart rate cable 2. Main I/O cable 3. Coax cable 4. DC power cable Note: If the unit is not equipped with Personal View- ing Screen, the coax and DC power cables should be tucked down the neck as they are part of the PVS Kit. Step 11. Step 12. Next, plug-in the heart rate cable into the HR Pl
Résumé du contenu de la page N° 8
2 1 Step 13. Step 14. Assemble the front and back display parts to- Using provided Phillips head screw driver, se- gether by sliding the bottom of the front display cure the front display to the back with (8) M4 x under the 2 tabs at the base first, then pressing 0.7 x 19mm long Phillips head screws. front display against the back cover. Caution: Be careful not to pinch any wires. Step 15. Step 16. Locate left side upper body arm, move to left Install the left arm and secure with
Résumé du contenu de la page N° 9
Step 17. Step 18. Place the Total Body Trainer on the floor in the Perform a visual inspection, and test the fea- position it will be used. Then adjust leveling tures and functions of the unit prior to use. feet to assure that the Total Body Trainer is lev- Note: Refer to the User’s Manual for other settings eled to the floor and does not rock back and and instructions. forth. YOU HAVE NOW COMPLETED THE INSTALLATION OF YOUR TOTAL BODY TRAINER YOU HAVE NOW COMPLETED THE TOTAL BODY T
Résumé du contenu de la page N° 10
Use the checklist below to ensure the proper installation of the Total Body Trainer: 1. All parts, tools and hardware in the package are accounted for. 2. All screws are tightened and torqued down to their specified values. 3. Upper body arms are properly mounted and secured. 4. Upper body arms move freely, along the entire range of motion. 5. Upper neck is properly mounted and secured. 6. Display’s mounting bracket and back cover are properly mounted and secured. 7. All cables and
Résumé du contenu de la page N° 11
EMBEDDED DISPLAY CONSOLE INSTALLATION INSTRUCTIONS 2 3 1 1 4 2 3 5 Step 2. Step 1. Verify the tool kit has the following parts: Remove all contents from the packaging and verify that you have the following parts: Item Description QTY 1. Embedded display console. 2. Operation manual. Assembly instructions 1 1 3. Tool kit. Screw, Phillips Head, M4 x 19mm 18 2 4. Power adaptor (60W AC). Washer, flat, M4 5 3 5. Power cord. Step 3. Step 4. Be careful with the display an
Résumé du contenu de la page N° 12
Step 5. Step 6. Disconnect the ground cable from the ground Mount the back cover to the display mounting quick disconnect tab on the embedded display. bracket using four (4) M4 x 0.7 x 19mm long Save the cable for later use. Phillips head screws and four (4) M4 flat wash- ers. Step 7. Step 8. Attach the ground cable to upper left screw on Pullout the coax adapter from the tuner card on the mounting bracket and secure tightly. the embedded display. 13 620-7921 Rev A
Résumé du contenu de la page N° 13
After Before Step 9. Step 10. Now screw in the coax adaptor to the coax ca- Go back to the embedded display assembly and ble coming out of the base neck. remove the plastic tabs from the lower back cover. 3 2 4 1 Step 11. Step 12. Take the embedded display assembly to the Identify the four cables coming out of the neck base unit. Hold the front display plastics at the and mounting bracket: top with one hand while connecting the cables 1. Heart rate cable and harnesses with
Résumé du contenu de la page N° 14
Step 13. Step 14. Plug-in the heart rate cable from the neck into Plug-in the 12-pin main I/O cable from the neck the heart rate board connector on the FitCPU to the 12 pin connector on the FitCPU board of board of the embedded display assembly. the embedded display assembly. Step 15. Step 16. Next plug in the coax cable to the coax adapter Now plug in the DC power cable from the base on the tuner card of the embedded display as- neck to DC connectors on the embedded dis- sembly. play
Résumé du contenu de la page N° 15
Step 17. Step 18. Plug in the Heart rate ground cable into the Plug in the ground cable coming from upper left quick disconnect tab on the display mount. side of the display mounting bracket into the quick disconnect tab on the embedded display assembly. 2 1 Step 19. Step 20. Assemble the front and back display parts to- Using a Phillips head screw driver, secure the gether by sliding the bottom of the front display front display to the back with (8) M4 x 0.7 x under the 2 tabs at
Résumé du contenu de la page N° 16
Step 21. Step 22. Now it is time to connect entertainment cable Turn power on. Perform a visual inspection, and power to the unit. Connect the in-house and test the features and functions of the unit entertainment cable to the RF input at the base prior to use. of the unit. Note: Refer to the User’s Manual for other settings and instructions. Take the power supply from the kit and plug the small barrel connector to the DC input. Then take the power adapter cable from the kit a
Résumé du contenu de la page N° 17
Use the checklist below to ensure the proper installation of the Total Body Trainer: 1. All parts and hardware in the package are accounted for. 2. Embedded display assembly is clear of any scratches or damage. 3. All screws are tightened and torqued down to their specified values. 4. Display’s mounting bracket and back cover are properly mounted and secured. 5. All cables and harnesses are properly plugged to their respective connectors. 6. The front and back display plastics are pr
Résumé du contenu de la page N° 18
iPod® CENTER CONSOLE INSTALLATION INSTRUCTIONS 1 3 1 2 5 2 4 Step 1. Step 2. Remove all contents from the packaging and Verify the cable kit has the following two parts: verify that you have the following parts: 1. Center console power cable. 1. iPod® center console. 2. Headphone jack and mount. 2. iPod® cradle. 3. Owner’s manual. 4. Cable kit. 5. Lower back cover. Note: If the center console is being installed on a new unit, then perform this installation prior to mount
Résumé du contenu de la page N° 19
Step 5. Step 6. Disconnect the ground wire between the heart Disconnect the 12-pin serial connector from the rate board and the display mount. display Step 7. Step 8. Now disconnect the heart rate connector from Be careful with the display and place it face the display down on top of a non-scratching surface to pro- tect it from being damaged. 20 620-7921 Rev A
Résumé du contenu de la page N° 20
Step 9. Step 10. Using a #2 Phillips head screwdriver, remove Next remove the bottom cover, then remove the the (4) screws that hold bottom side of the dis- headphone blank cover. You will no longer play console on, then remove the (1) screw that need those covers and they can be stored away holds the headphone jack cap. for any possible future use. Note: Retain screws for later use. Step 11. Step 12. Using a Phillips head screwdriver, remove the Insert the new center console into
