Instruction d'utilisation Life Fitness X9I

Résumé du contenu de la page N° 1

X9i Cross-Trainer
A SSEMBLY INSTRUCTIONS

Résumé du contenu de la page N° 2

Congratulations... and welcome to the world of Life Fitness and the Life Fitness X9i Cross-Trainers The following Parts List and the step by step assembly procedures have been assembled to make the set-up of the Cross-Trainer as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Cross-Trainer.

Résumé du contenu de la page N° 3

IMPORTANT SAFETY INSTRUCTIONS! ⇒ DO NOT locate the Cross-Trainer outdoors, near swimming pools, or in areas of high humidity. ⇒ DO NOT operate your Cross-Trainer if it has been dropped, damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services at the number in the Operation Manual. ⇒ DO NOT locate the Cross-Trainer any closer than 30 inches (76 cm ) to a television set. ⇒ DO NOT locate additional Cross-Trainers any closer than 42 inches (10

Résumé du contenu de la page N° 4

TOOLS REQUIRED FOR ASSEMBLY... Magnetic #2 Bit Phillips Screwdriver, 5/16" & 3/16" Hex Key Wrenches, 1/2" Open End Wrench PARTS LIST 1 Hex socket Head Cap Screw Qty: 8 2 Phillips Pan Head Screw Qty: 8 3/8-16 x 1” #8-18 x 10” 0017-00101-1645 0017-00101-1744 3 Phillips Pan Head Screw Qty: 14 4 Console Assembly Qty: 1 #8-18 x 3/4” AK61-00193-0001 0017-00101-1242 5 Front Monocolumn Cover Qty: 1 6 Back Monocolumn Cover Qty: 1 0K61-06350-0003 0K61-06351-0003 7 Console Support Assembly Qty: 1 8 Flat

Résumé du contenu de la page N° 5

Step 1 Before proceeding, familiarize yourself with the parts of the Cross-Trainer and make sure that you have received all the items described in the Parts List. Step 2 Locate the left and right FRONT COVER (#9, #10). Usign two PHILLIPS PAN HEAD SCREWS (#3), mount the USER LEFT FRONT COVER (#9) to the FRAME (A). Attach the USER RIGHT FRONT COVER (#10) to the FRAME in the same manner using two PHILLIPS PAN HEAD SCREWS (#3). Secure the tops of the FRONT COVERS together using two PHILLIPS PAN HEAD

Résumé du contenu de la page N° 6

Step 4 Detach and unwrap the WIRE HARNESS (E) (10P, 3P, 4P) located at the top of the MONOCOLMN (F). Holding the CONSOLE SUPPORT ASSEMBLY (#7) with the handgrips facing upward, feed the WIRE HARNESS up through the neck and out the top access hole. Carefully 3P 4P 4 lower the CONSOLE SUPPORT ASSEMBLY into the MONOCOLUMN. 10P CAUTION: BE CAREFUL NOT TO PINCH THE WIRE HAR- NESSES (E) WHEN ASSEMBLING THE CONSOLE SUP- PORT ASSEMBLY (#7) TO THE MONOCOLUMN (F) 17 MISE EN GARDE : VEILLEZ À NE PAS PINCE

Résumé du contenu de la page N° 7

Step 10 Locate the POLAR RECEIVER (#16). Slide the FOAM ISOLATOR (#15) over the POLAR RECEIVER. Remove the POLAR RECEIVER JACK (G) from the tape and plug the POLAR RECEIVER into the POLAR RECEIVER JACK. Step 11 Locate the front and back MONOCOLUMN COVERS (#5 & #6). With the wire positioned on top, carefully insert the POLAR RECEIVER (#16) between the vertical ribs located inside the BACK MONOCOLUMN COVER (#6). Place the BACK MONOCOLUMN COVER (#6) over the PIVOT SHAFT (H) at the top of the MONOCO

Résumé du contenu de la page N° 8

PRE-OPERATION CHECKLIST Ensure that all fastener are tight. Make sure the CROSS-TRAINER is properly leveled and stable. (Refer to the Operation Manual) Ensure that the Leveler Jam Nuts are tight. (Refer to the Operation Manual) Read the entire Operation manual before using the Cross-Trainer. LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE Vérifiez si tous les dispositifs de fixation sont serrés Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable. (Référez-vous