Résumé du contenu de la page N° 1
INSTALLATION GUIDE
Undercounter Refrigeration
Résumé du contenu de la page N° 2
Contents Important Note Undercounter Refrigeration . . . . . . . . . . . . . . . . . . . . . 3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of Undercounter Specifications . . . . . . . . . . . . . . . . . . . . 4 highlighted information throughout this guide: Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 IMPORTANT NOTE highlights information that is especially Undercounter Installation . . . . . . .
Résumé du contenu de la page N° 3
Undercounter Refrigeration 3 subzero.com/specs Sub-Zero Undercounter Refrigeration IMPORTANT NOTE: The importance of the installation of RATING PLATE the Sub-Zero undercounter unit cannot be overempha- sized. Installation should be done by a qualified installer. Before you begin the installation process, it is recom- mended that you read this entire installation guide. There are key details that you should take special care to observe during the installation. By reading these instruc- tions care
Résumé du contenu de la page N° 4
Undercounter Specifications 4 Undercounter Models OVERALL DIMENSIONS OPENING DIMENSIONS 7 23 /8" (606) 24" (610) TOP VIEW 24" (610) OPENING DEPTH 34" (864) 4" (102) 1 24" (610) 34 /2" (876) 24" (610) OPENING DEPTH OPENING OPENING WIDTH HEIGHT 3 25 /8" (645) SIDE VIEW FRONT VIEW 3 1 /4" (44) SPECIFICATIONS Shipping Weight lbs (kg) All Models 130 (59)
Résumé du contenu de la page N° 5
Site Preparation 5 subzero.com/specs Before You Start Make sure the opening dimensions, door clearance, TOOLS AND MATERIALS REQUIRED electrical service and plumbing are correct for the model • Appliance dolly able to support 130 lbs (59 kg) you are about to install. Refer to specifications on the • Level—2' (.6 m) and 4' (1.2 m) recommended following pages. • Phillips and slotted screwdriver sets IMPORTANT NOTE: To operate properly, the door must open a minimum of 90°. Use a minimum 3" (76) fill
Résumé du contenu de la page N° 6
Site Preparation 6 Electrical Requirements Plumbing Requirements The electrical supply should be located within the shaded MODEL UC-24CI area shown in the illustration below. Follow the National For model UC-24CI, the water supply line for the ice Electrical Code and local codes and ordinances when maker should be located within the shaded area shown in installing the receptacle. A separate circuit, servicing only the illustration below. Connect the water line from the ice this appliance is requ
Résumé du contenu de la page N° 7
Undercounter Installation 7 subzero.com/specs Unpack the Unit Anti-Tip Bracket Before moving the undercounter unit into position, make sure all opening dimensions, electrical and plumbing To prevent the unit from tipping forward and provide a requirements are complete and accurate. stable installation, the unit must be secured in place IMPORTANT NOTE: The floor under the undercounter unit with the anti-tip bracket. must be at the same level as the surrounding finished floor to allow for removal
Résumé du contenu de la page N° 8
Undercounter Installation 8 Installation IMPORTANT NOTE: If the undercounter unit has been laid WATER LINE CONNECTION (MODEL UC-24CI) on its back or side, you must allow the unit to stand upright For model UC-24CI, connect the plastic tubing from the for a minimum of 24 hours before connecting power. ice maker to the house water supply line with the fitting With the undercounter unit near the installation opening, connection kit, provided. Check all water line fittings for plug the power cord in
Résumé du contenu de la page N° 9
Undercounter Installation 9 subzero.com/specs Door Panel MODELS UC-24R AND UC-24C(I) Panel Specifications OVERLAY PANEL WH Models UC-24R and UC-24C(I) can be fitted with a 3 1 UC-24R, UC-24BG, UC-24C(I) 23 /4" (603) 30 /16" (764) custom overlay or stainless steel door front panel. A stain- RAILS AND STILES W less steel door panel with tubular or pro handle is available 1 UC-24BG 2 /4" (57) min as a sales accessory. Installation of the stainless steel MAX PANEL WEIGHT panel will be required. UC-2
Résumé du contenu de la page N° 10
Undercounter Installation 10 Overlay Panel Installation MODELS UC-24R AND UC-24C(I) Before attaching the overlay panel to the door, insert two screws, one in the center of each mounting position, just Inspect the overlay door panel for minimum thickness and far enough that the slotted holes on the hinge side door weight limit. Remove the two panel mounting brackets panel bracket will slide under the heads. These positioning attached to the front of the door and set aside. screws will support the
Résumé du contenu de la page N° 11
Undercounter Installation 11 subzero.com/specs Overlay Panel Installation BEVERAGE CENTER MODEL UC-24BG Remove the door panel from the door frame and remove tenon centers. Open the door. Using the center marks to Inspect the overlay door panel for minimum thickness, locate screws, drive the screws into the panel through the weight limit and finished inside edges. Decide if the handle black tape on the door frame. will be attached through the glass door frame or just through the decorative door p
Résumé du contenu de la page N° 12
Undercounter Installation 12 Overlay Panel Installation Hinge Adjustment IMPORTANT NOTE: The undercounter unit should be properly leveled before door hinge adjustments are made. The model UC-24BG glass door is made with a sealed, double-wall tempered glass core. The drill must not The top and bottom cabinet hinges are held in place with contact this core when drilling. Be sure the hole is three permanent adjustment screws. If the door needs centered on the small groove in the front of the door a
Résumé du contenu de la page N° 13
Undercounter Installation 13 subzero.com/specs Installation Checklist To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Has all packing material been removed? Turn the unit on. Is it operating properly? If not, is the unit plugged in? Is the control turned on? Is the power cord plugged into a properly grounded 3-prong outlet, which has been installed in accordance with all applica
Résumé du contenu de la page N° 14
Service Information 14 Service Information If service is necessary, maintain the quality built into your undercounter unit by calling Sub-Zero factory certified If you are storing or disposing of your old refrigerator service. or freezer, please do it safely. Remove the For the name and number of Sub-Zero factory certified doors or tightly secure service nearest you, check the contact & support section the doors closed. of our website, subzero.com or call Sub-Zero customer Child entrapment care
Résumé du contenu de la page N° 15
The information and images in this guide are the copyright property of Sub-Zero, Inc. Neither this guide nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero, Inc. ©Sub-Zero, Inc. all rights reserved. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Ca
Résumé du contenu de la page N° 16
SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7023606 REV-A 12/2011
