Instruction d'utilisation Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300

Instruction d'utilisation pour le dispositif Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300

Dispositif: Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300
Catégorie: Refrigérateur
Fabricant: Honeywell
Dimension: 0.63 MB
Date d'addition: 12/21/2013
Nombre des pages: 20
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300.

Pour votre confort

Si regarder l'instruction Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 20 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

PCR-300
PCR-300 RC
Installation and Operating
Instructions
Electronic refrigeration control
EB-PCR-04 EN1H-1924GE23 R1207

Résumé du contenu de la page N° 2

TABLE OF CONTENTS 11 Unpacking the unit and conditions of use 3 12 General instructions 3 13 Use and function 3 3.1 Use for the purpose intended 3 3.2 Function 4 14 Safety 4 4.1 Sources of danger 4 4.2 Safety precautions 5 15 Installation and commissioning 5 5.1 Mechanical installation 5 5.2 Electrical installation 6 5.3 Setting the DIP switch for the emergency setpoint and clock back-up battery 8 16 Operating of the controller 9 6.1 Switching on the operating voltage 9 6.2 Display 9 6.3 Key fu

Résumé du contenu de la page N° 3

1 Unpacking the unit and conditions of use Before and when unpacking the unit, make a visual inspection to identify any possible damage which may have occurred during transportation. Please look for loose parts, dents, scratches, etc. Report any damage immediately to the freight company. (Please see “Conditions if damage has occurred”.) In other cases, the latest edition of the “General conditions for the supply of goods and services” issued by the ZVEI (German Central Association for the Electr

Résumé du contenu de la page N° 4

I The controller must not be used as a safety cut-out device or excess temperature limiter. If the controller is used for purposes other than those stated here, it shall not be considered to be use for the purpose intended. I Only connect sensors supplied with the unit. If a replacement sen- sor is required, only use sensors of the same type (part no. H61007). I The controller is not intended for use in vehicles because the possible operating voltage ranges, interference level and environmental

Résumé du contenu de la page N° 5

I Never expose the unit to excessive heat, dust and vibrations. Avoid knocks and pressure loads. If the housing is damaged, there is a risk of an electric shock causing death or injury. I If the unit cannot be operated without the risk of danger, it must be taken out of service and precautions taken so that it cannot be switched on again unintentionally. This applies, in particular, if: u The housing has damage which is visible, u the unit is no longer operational or u it has been stored for a

Résumé du contenu de la page N° 6

a) housing with 2 mounting tabs: open out the lateral mounting tabs; clip the unit on the 35 mm rail and press tabs in again. b) housings with 1 mounting tab: put housing on the upper 35 mm rail. Clip the unit on the 35 mm rail, lower tab clips on the rail automatically. To remove the unit from the rail press in lower mounting tab with a screw driver, lift unit. I Mounting of sensor: I Use a cable clamp to secure sensor T1 in a suitable position. I Secure evaporator sensor T2 in the evaporato

Résumé du contenu de la page N° 7

Terminal: Description: 1 - 2 T1 = Cold store sensor 3 - 4 T2 = Evaporator sensor 10 - 12 Mains = Power supply 13 - 15 V = Compressor contactor (cooling) 17 - 18 Ev = Evaporator fan (contactor) 20 - 21 Alarm = Remote alarm indicator; indicator lamp or contactor (with RC-element) 23 - 24 Def = Defrost heating (contactor) or hot gas valve * The unit is equipped with an opto-decoupled electronic alarm output. Take note of the alarm output limit values. I Supply voltage: Max. 250 V AC. I Minimu

Résumé du contenu de la page N° 8

5.3 Setting the DIP switch for the emergency setpoint and the clock back-up battery Carefully lift the housing cover off the side, using your fingers. I Selection of the emergency setpoint for the cold store temperature: This will be activated if the data in the memory is lost and alarm AL1 is activated. This sets all program parameters to the preset value. The cold store temperature setpoint can be preset to +4 °C or –18 °C, as desired. This ensures that chilling systems with temperatures above

Résumé du contenu de la page N° 9

* Note: It takes approximately 24 hours for the battery to achieve its full back-up capacity. The battery will provide cover for a power failure of approximately 1 month. 6 Operation of the controller Front view of controller: 6.1 Switching on the operating voltage The controller is started by means of a control switch provided by the customer. The first time the controller is started, pre-programmed setting values are used which at later point can be adapted for individual requirements. If ala

Résumé du contenu de la page N° 10

Three spot indicators show the switching status of the relays during operation: Pos. 1: On : Compressor relay on. Off: Compressor relay off. Flashes: Compressor start-up delay E05 active. Pos. 2: On : Evaporator fan relay on. Off: Evaporator fan relay off. Pos. 3: On : Defrost relay on. Off: Defrost relay off. Flashes: Drain time E09 is running. 6.3 Key functions * Never operate the keys with sharp objects (screwdriver or similar). Display of setpoint Press and hold down key. temperature Clear

Résumé du contenu de la page N° 11

u Access the first programming level by pressing the and keys at the same time for 5 seconds. u Then use the and keys to access the parameters to be changed. u Access the second programming level by pressing the and and keys simultaneously for 5 seconds. I To exit from the programming levels and save the data, press the key after the last input parameter. If no key is pressed in either of the programming levels for 10 minutes, this mode will be exited without the data being saved. I Do not

Résumé du contenu de la page N° 12

If the set temperature difference E03 is negative, an alarm is given if it is too cold in the refrigerated area, e.g. E03 = –10 K, cold store setpoint = –18 °C alarm at –28 °C in refrigerated area. If the set temperature difference E03 is positive, the alarm is given if it is too warm in the refrigerated area, e.g. E03 = +10 K, cold store setpoint value = –18 °C alarm at –8 °C in the refrigerated area. Attention: any change of the cold store setpoint valve changes also the alarm temperat

Résumé du contenu de la page N° 13

6.7 Manual defrosting Press and hold down the key for 5 seconds. The manual defrosting process will be initiated. 7 Programming Access to the second programming level: I Press and hold down the , and keys at the same time for approx. 5 seconds (Display: E01 for PCR-300, E00 for PCR-300RC). I Use or key to select parameters. I Setting: Press and hold down the key. Adjust the setpoint value to the desired figure using the or key. I Do not display altered parameter data before saving the data, as

Résumé du contenu de la page N° 14

The time is entered in increments of 10 minutes in each case . Important: The times must be entered in ascending order. E03 Alarm temperature difference –50 K to + 50 K 20 K E04 Delay time – Alarm 0 to 99 mins. 10 mins. E05 Compressor start-up delay 0 to 15 mins. 5 mins. E06 Defrost type 1 or 2 1 1 = Electrical (compressor off) 2 = Hot gas (compressor on) E07 Defrost limit temperature 0 to 50 °C 8 °C E08 Defrost time limit 1 to 99 mins. 25 mins. E09 Drainage time, evaporator 0 to 99 mins. 3 mi

Résumé du contenu de la page N° 15

E15 Sensor calibration T1 –5 to +5 K 0 K (cold store) E16 Sensor calibration T2 –5 to +5 K 0 K (evaporator) E17 Operation of 0 = Relay de-energizes 2 compressor relay 1 = Relay is perma- if cold store sensor T1 nently engergized is defective 2 = Alternately ener- gized/de-ener- gized according to time set in E18 and E19. E18 “On” time at E17 1 to 99 mins. 15 mins. E19 “Off” time at E17 1 to 99 mins. 15 mins. To exit from the programming mode: Press the key after inputting the last level. 7.2

Résumé du contenu de la page N° 16

8 Maintenance The controller does not require any maintenance. It does not have any fuses so, if brief voltage spikes occur, the refrigeration system will not stop operating for a prolonged period. Once the disturbance has passed, the controller will automatically start up again. Cleaning the housing: Only a dry anti-static cloth may be used to wipe clean all plastic parts. Do not use water or cleaning agents containing solvents! 9 Alarm messages If an alarm occurs, the alarm output will be acti

Résumé du contenu de la page N° 17

Clearing alarm: Press the key. All alarm messages, with the exception of AL2, are also reset by switching off the operating voltage. AL2 can only be reset using the key. 10 Problem solving Fault Cause Remedy Evaporator fan does not Evaporator Refit switch on during sensor T2 has sensor. cooling when the fallen out of programmed setting the fins. of parameter E11 is set to position 3 (fan run-on). For PCR-300RC only: Back-up battery Switch on The real-time clock is switched off. back-up stop

Résumé du contenu de la page N° 18

12 Technical data Mains voltage/frequency 230 V AC ± 10% / 50/60 Hz Rated wattage 2.5 watts Display 3-digit, 7-segment, red LED, 14.2 mm Resolution 1 K Measuring range –55 to +50 °C Outputs 1 relay with changeover contact, 8 A, 230 V AC, resistive load, (cooling). 1 relay with N.O. contact, 8 A (5A PCR-300RC), 230 V AC, resistive load, (defrost heating). 1 relay with N.O. contact, 8 A (5A -PCR-300RC), 230 V AC, resistive load (fan control). Control response Two-step Alarm output Opto bidirec

Résumé du contenu de la page N° 19

EC Declaration of Conformity as defined in the EMC Directives 89/336/EEC and the EC Low Voltage Directives 73/23/EEC Product: FLICA, electronic coldstore control Model designation: PRC-300, PCR-300RC has been developed, designed and manufactured in accordance with the EC Standards listed above. The following harmonized Standards have been applied: EN 50081-1 (1991) Part 1 for the trades sector, emitted interference EN 50081-2 (1993) Part 1 for the industrial sector, emitted interference EN 500

Résumé du contenu de la page N° 20

Automation and Control Solutions Honeywell GmbH Hardhofweg • 74821 Mosbach / Germany Phone: +49 (0) 62 61 / 81-475 Fax: +49 (0) 62 61 / 81-461 E-Mail: Cooling.Mosbach@honeywell.com www.honeywell-cooling.com


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Honeywell 88037 Manuel d'utilisation Refrigérateur 0
2 Honeywell ELECTRONIC REFRIGERATION CONTROL PCR-300 RC Manuel d'utilisation Refrigérateur 118
3 Honeywell FG-701 Manuel d'utilisation Refrigérateur 11
4 2JANE Surround Sound System HTS-GS1 Manuel d'utilisation Refrigérateur 4
5 3Com Phaser 7750 Manuel d'utilisation Refrigérateur 1
6 3Com iQ 10 Manuel d'utilisation Refrigérateur 0
7 3Com PowerDual iQ 10 iQ 10C Manuel d'utilisation Refrigérateur 1
8 3Com PowerDual iQ 10 iQ 10P Manuel d'utilisation Refrigérateur 2
9 3Com Dell D-Family Battery Charger CHRG01L Manuel d'utilisation Refrigérateur 0
10 3Com PowerDual iQ 10 iQ 10PC Manuel d'utilisation Refrigérateur 0
11 3Com Preface Firmware Version 1.07 VFD-D D Manuel d'utilisation Refrigérateur 0
12 3D Connexion Infinity Systems Interlude IL120s Manuel d'utilisation Refrigérateur 1
13 3D Connexion Cisco Catalyst Blade Switch 3040 for FSC Hardware OL-10694-01 Manuel d'utilisation Refrigérateur 0
14 3D Connexion 42" SNOW THROWER LST42B Manuel d'utilisation Refrigérateur 0
15 3D Connexion Cisco SCA BB SNMP Real Time Monitoring OL-12491-01 Manuel d'utilisation Refrigérateur 0