Résumé du contenu de la page N° 1
CD PLAYER
DPF-1030
DPF-2030
INSTRUCTION MANUAL
KENWOOD CORPORATION
B60-4517-08 (EN)
Résumé du contenu de la page N° 2
Introduction Caution : Read this section carefully to ensure safe operation. Before applying power 2 Units are designed for operation as follows. Australia .................................................................................. AC 240 V only *Other countries ............................ AC 110-120 / 220-240 V switchable Europe and U.K. ..................................................................... AC 230 V only *AC voltage selection AC voltage selector switch The AC voltage sel
Résumé du contenu de la page N° 3
Introduction Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for 3 shipping damage. We recommend that you retain the o
Résumé du contenu de la page N° 4
Caution : Read this page carefully to ensure IMPORTANT SAFEGUARDS safe operation. Please read all of the safety and operating instructions before 10.Cleaning – Unplug this appliance from the wall outlet operating this appliance. Adhere to all warnings on the appliance before cleaning. Do not use volatile solvents such as 4 and in the instruction manual. Follow all the safety and operating alcohol, paint thinner, gasoline, or benzine, etc. to clean instructions. These safety and operating instr
Résumé du contenu de la page N° 5
5
Résumé du contenu de la page N° 6
System connections Malfunction of microcomputer Caution: If operation is not possible or erroneous display appears even Do not plug in the power lead until all connections are com- though all connections have been made properly, reset the 6 pleted. microcomputer referring to “In case of difficulty”. ª Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Caution Be sure to adhere followings. Or proper vent
Résumé du contenu de la page N° 7
System connections 7 Connection to a general-use amplifier Use the provided audio cords to connect the OUTPUT jacks of this unit to the CD input jacks (or AUX jacks) of the amplifier. Connection to digital amplifier, MD or CD-R Connect the DIGITAL OUTPUT (OPTICAL) jack to the digital input jack of the amplifier, DAT recorder, MD recorder, etc., using an optical fiber cable (sold separately) which are commercially available in audio stores. Optical fiber cable ÖWhen using an optical fiber cable t
Résumé du contenu de la page N° 8
System connections 8 SYSTEM CONTROL SYSTEM CONTROL CONNECTIONS Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. SYSTEM CONTROL This unit is compatible only with the [SL16] mode. The system con- trol operation is not available if the unit is connected in the [XS-8] connection mode. SYSTEM CONTROL SYSTEM CONTROL SYSTEM CONTROL ÖDo this operation after completing all connections. (Ensure that th
Résumé du contenu de la page N° 9
Maintenance Disc handling precautions Discs which can be played with this unit DVD (12 cm, 8cm), CD (12 cm, 8 cm), VCD, and the audio part of CDV, CD- 9 G, CD-EG and CD-EXTRA. Handling Use discs that comply with the IEC standard, for example a disc carrying Hold the discs so that you do not touch the COMPACT COMPACT the marking on the label surface. playing surface. DIGITAL AUDIO DIGITAL AUDIO Label side Playing side Never play a cracked or warped disc During playback, the disc rotates at high
Résumé du contenu de la page N° 10
Controls and indicators 10 REPEAT indicator CCRS indicator Program SINGLE TIME indicator check indicator EDIT indicator TOTAL TIME indicator A B REPEAT CCRS TRACK 1 2 3 4 5 TRACK EDIT SINGLE TIME TRACK mode indicator NO. TOTAL TIME P.C. PGM 6 7 8 9 10 Program mode indicator 11 12 13 14 15 _ : 16 17 18 19 20 88 88 88 Pause indicator TIME indicator, program No. Play track No. in- Play indicator Music calender Output level indicator dicator The figure shows an example for the DPF-2030 DISPL
Résumé du contenu de la page N° 11
(DPF-2030 only) Operation of remote control unit The keys with the same name as those on the main unit operate the same way as the main unit. The keys marked * are provided only on the remote control unit. TIME DISP12 3 11 1 TIME DISPLAY key # 5 Numeric keys ( 1 1 1 1 1 ~ ) ) ) ) ) , 0 0 0 0 0 ) # 1 P.MODE 45 6 2 Program-related keys 6 Basic function keys EDIT 78 9 5 2 P.MODE key $ Skip keys (4,¢) # CLEAR CHECK 0 +10 Search keys (1,Á) # EDIT key * RANDOM CLEAR key %( Stop key (7) @ 3 CHECK key
Résumé du contenu de la page N° 12
7 6 0 4 ¢ 1Á Normal play (TRACK mode) Use the following procedure to play a CD in the original order of tracks from track No. 1. The figure shows an example for the DPF-2030 12 76 0 4¢
1Á
: Keys and control used in the operations described on this page. Playing tracks in order from track No. 1 Press the POWER switch to ON. 1 POWER 0 - ON Ð OFF ÖPlayback starts when a disc has been loaded. Load a disc. 2 1Open the tray. OPEN/CLOSE 0 0 ÖDo not touch the played side of disc. 2Place a disc. ÖLo
Résumé du contenu de la page N° 13
Normal play (TRACK mode) Playback from desired track (except for DPF-1030) (Remote control unit only) Press the numeric keys as shown below.... 13 1 2 3 4 5 6 To enter track No. 23 : 003 To enter track No. 40 : 0000) 7 8 9 0 +10 REMOTE CONTROL UNIT RC-P0715 ÖPlayback starts from the selected track and continues on the subse- quent tracks. Skipping tracks To skip To skip backward forward 0 4¢
Ö The track in the direction of the pressed key is skipped, and the selected track will be played from
Résumé du contenu de la page N° 14
Programmed play (PGM mode) Use the following procedure to program desired tracks in a desired order. (up to 20 tracks) The figure shows an example for the DPF-2030 14 Preparation Ö Load a disc in the CD player. @ 0 76 4¢
1Á
: Keys and control used in the operations described on this page. Press so that the “PGM” indicator lights. 1 Lights up. Do this operation in the stop mode. P.MODE 0 TRACK NO. PGM 01 Go to step 2 within 5 seconds. Program desired tracks. 2 1 Select the desired track No. Re
Résumé du contenu de la page N° 15
Programmed play (PGM mode) Auto space function During programming of tracks, a non-recorded space of a few seconds will be automatically created between tracks. By recording 15 tracks with these spaces on tape, the search and repeat play operations of tape using the DPSS function (which works by searching the non-recorded spaces) can be performed reliably. Ö Even when the performances of two tracks are continuous (which occurs with classical or live recording music), the spaces will be create
Résumé du contenu de la page N° 16
Repeated playback Preparation Ö Load a disc in the CD player. @ The figure shows an example for the DPF-2030 16 ª 0 76 4¢
1Á
: Keys and control used in the operations described on this page. To repeat only the programmed tracks Do this operation in the stop mode. Lights up. 1 Press so that the "PGM" indicator lights. TRACK NO. PGM P.MODE 0 01 2 Select the desired track No. Main unit Remote control unit ÖAll of the programmed tracks will be repeated. (Except for DPF-1030) (Except for DPF-2030)
Résumé du contenu de la page N° 17
Repeated playback The figure shows an example for the DPF-2030 17 76 0 4¢
1Á
: Keys and control used in the operations described on this page. To repeat the entire disc Press so that the “TRACK” indicator 1 Lights up. lights. If the "PGM" indicator is lit, press the TRACK TRACK NO. P.MODE key. P.MODE 01 0 Lights up. Switch REPEAT ON. 2 REPEAT TRACK TRACK REPEAT NO. PGM 0 01 3 Start playback. 0 6 To cancel repeated playback Goes off. Press the REPEAT key again. REPEAT TRACK TRACK REPEAT NO.
Résumé du contenu de la page N° 18
Editing The following procedure allows to record a CD within the specified tape length so that no music is interrupted in the middle at the ends of sides A and B. The figure shows an example for the DPF-2030 18 Preparation Ö Load a disc in the CD player. @ 76 0 Ö Press the stop (7) key to set the unit in the 4¢
1Á
stop mode. Ö Make sure the PGM indicator is extinguished. $ : Keys and control used in the operations described on this page. Light the “EDIT” indicator. 1 Lights up. Lights up. EDI
Résumé du contenu de la page N° 19
Editing The figure shows an example for the DPF-2030 19 0 76 4¢
1Á
: Keys and control used in the operations described on this page. To check the edited contents Lights up. A 5 EDIT P.C. CHECK 0 FI LE ÖWhen the CHECK key is pressed, track numbers and remaining time in the file A are displayed first, then those in the file B. ÖThe "P.C." indicator goes off in a few seconds. To clear the edited contents Press any one of these keys. P.MODE CLEAR 0 OPEN/CLOSE 0 0 ÖThe edited data is cleared entir
Résumé du contenu de la page N° 20
Playback in a random order (Random playback) As tracks are selected at random, you can enjoy listening to for a long time. The figure shows an example for the DPF-2030 20 Preparation Ö Load a disc in the CD player. @ ª 76 0 4¢
1Á
: Keys and control used in the operations described on this page. Press the P.MODE key so that the "TRACK" 1 indicator lights. If the "PGM" indicator is lit, press the Lights up. P.MODE key. TRACK 1 2 3 4 5 TRACK SINGLE TIME NO. 6 7 8 9 10 P.MODE 0 01 00 : 0 Press
