Instruction d'utilisation Maytag 53-3442

Résumé du contenu de la page N° 1

'h '1,
PLEASE READ ALL INSTALLATION
INSTRUCTIONS AND REQUIREMENTS
BEFORE INSTALLING
ELECTRIC
WARNING
OR'IOUR SAFETY
Do not store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.
• %
3/8"DEEP WELL DRIVER CHANNEL LOCK PLIERS SCREWDRIVER PUTTY KNIFE DUCT TAPE
1/,,-DRIVER OR ADJUSTABLE WRENCH (BLADE & TORX)
INSTALLINGYOUR NEW DRYER BACKGUARD
/
FORYOURSAFETY ANDTHE PROPER OPERA- //
/
TION OFYOUR NEW DRYER,THE DRYER
MUST BE INSTALLEDIN ACCORDANCEWITH

Résumé du contenu de la page N° 2

NSTALLATION REC!UREMENTS PLEASE READ All Installation Instructions and Requirements Before Installing Power Cord. IT IS RECOMMENDED THAT A QUALIRED ELECTRk Dryers installed in manufactured (mobile) homes must be ClAN OR SERVICETECHNICIAN INSTALLYOUR DRYER. connected with 4 conductor type SRD or SRDT cord to a 3 pole, 4 wire grounding type receptacle; by metal-clad cable; or suitable conductors enclosed in flexible metal conduit. If LOCATION using metal-clad cable or flexible conduit, leave at le

Résumé du contenu de la page N° 3

3. Route the power cord (pigtail) or cable conductors through the strain relief clamp. FIG. #2 - 4 WIRE TERMINALBLOCK ,_ CAUTION - The conductorsshould not extend into I connections. (BLACK) GREEN the dryer more than necessary to make the electrical J LINEt _/IRE 4. Refer to the Typical Electricalconnections listed below and make the electrical connections as instructed. We recommend that a qualifiedservice technicianor electri- NEUTRAL GROUND clan be consulted before connectingthe dryer. (WHITE

Résumé du contenu de la page N° 4

1. LEVELING 2. STABILITY WITH HANDS FOOT TO CHECK IF LEVELAND / STABLE Set all leveling feet at same height. A Place dryer in the location where it will minimum of Y2'clearance between the be used. Check, by rocking dryer with machine and the floor is recommend- hands on opposite corners, that all ed. Adjust to match the height of your four (4) feet are in firm contact with the dryer, floor. If it rocks, adjust as needed. 3A. OUTSIDEWALL 3B. BASEMENTWALL 3C. FLOOREXHAUSTING r BASEMENTWIJNBOW WAL

Résumé du contenu de la page N° 5

EXHAUSTVENTING RECUIREMENTS VENTHOODTYPE WARNINI FIRE HAZARD Numberof NEVER EXHAUST INTO A CHIMNEY, DUCT, GAS Separated 90°Turns by -- [_ VENT, WALL, CEILING, ATTIC, CONFINED SPACE, at least4 ft. BEDROOM, OR UNDER A BUILDING. ofStraighRu t n _]OPENING/n 4" OPENII_ NG_ 2_" J DO NOT USE VINYL, PLASTIC, CLOTH OR OTHER 0 45feet 30feet NONMETALIC DUCT TO EXHAUSTTHE DRYER. 1 35feet 20feet MULTIPLE INSTALLATIONS REQUIRE INDIVIDUAL 2 25feet 10feet EXHAUST SYSTEMS. Vent should never exceed 0.6 inches wat

Résumé du contenu de la page N° 6

9. Saw a 4',_" hole in floor and position dryer. When exhausting from the side, the installation should be 10. Secure the shortened pipe to the blower housing with a made according to the steps described in BOTTOM screw at the top and seal all joints with tape or silicone EXHAUSTING and as noted above. bathtub caulk. 11. Install a 4" 90 degree elbow as shown. INDOOR EXHAUSTING Step #3D shows a typical installationwith indoor exhausting. Indoor exhausting is not recommended unless the laundry FIG