Résumé du contenu de la page N° 1
DV365*
Gas and Electric Dryer
user manual
This manual is made with 100% recycled paper.
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service or accessory
parts, please register your product at or contact
www.samsung.com/register
1-800-SAMSUNG (726-7864)
D DV365_03064C-04_EN.indd 1 V365_03064C-04_EN.indd 1 2 2013-12-12 6:07:23 013-12-12 6:07:23
Résumé du contenu de la page N° 2
contents 3 What you need to know about Safety Instructions SAFETY INSTRUCTIONS 3 Important safety symbols and precautions 5 What to do if you smell gas : 3 7 Unpacking your dryer INSTALLING YOUR DRYER 7 The dryer’s exterior 8 Key installation requirements 7 8 Tools needed for installation 8 Replacement parts and accessories 9 Ducting requirements 10 Important to installer 10 Location considerations 10 Alcove or closet installation 11 Mobile home installation 11 Exhausting 12 Gas requirements 13
Résumé du contenu de la page N° 3
01 safety instructions safety instructions Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many benefits and features. WARNING - Risk of Fire � Clothes dryer installation must be performed by a qualified installer. � Install the clothes dryer according to the manufacturer’s instructions and local codes. � Do not insta
Résumé du contenu de la page N° 4
safety instructions IMPORTANT SAFTY INSTRUCTION WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your WARNING appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3. Do
Résumé du contenu de la page N° 5
01 safety instructions WHAT TO DO IF YOU SMELL GAS : � Do not try to light any appliance. � Do not turn on the appliance. � Do not touch any electrical switch. � Do not use any phone in your building. � Clear the room, building or area of all occupants. � Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. � If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, servic
Résumé du contenu de la page N° 6
safety instructions This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded adequately and in accordance with local and national codes. See the installation instructions for information about grounding this appliance. Do not sit on top of the dryer. Because of continuing product improvements, Samsung reserves the right to change specifications without notice. For complete details, see the Installation Instructions packed with your product be
Résumé du contenu de la page N° 7
02 installing your dryer installing your dryer UNPACKING YOUR DRYER Unpack your Dryer and inspect it for shipping damage. If your Dryer was damaged during shipping, contact 1-800-SAMSUNG (726-7864).To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer. Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene, WARNING etc.) well out of children’s reach. THE DRYER’S EXTERIOR [ BACK ] Control panel Filtro
Résumé du contenu de la page N° 8
installing your dryer KEY INSTALLATION REQUIREMENTS Hire a professional to install this dryer properly. If a service call has to be made as a result of poor setup, adjustment, or connection, it is considered the responsibility of the installer. If you install the dryer, you are responsible. Make sure you have everything necessary for proper installation: � A GROUNDED ELECTRICAL OUTLET. See Electrical Requirements. See page 15. � A POWER CORD for electric dryers (except Canada). See page 16. �
Résumé du contenu de la page N° 9
02 installing your dryer DUCTING REQUIREMENTS � Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. � Do not use a smaller duct. � Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation. Lint accumulation should be cleaned regularly. � If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too s
Résumé du contenu de la page N° 10
installing your dryer If the new Dryer is being installed into an existing exhaust system, you must make sure: � The exhaust system meets all local, state, and national codes. � That a flexible plastic duct is not used. � To Inspect and clean all lint buildup from inside the existing duct. � The duct is not kinked or crushed. � The exhaust hood damper opens and closes freely. The static pressure in any exhaust system must not exceed 0.83 inches of water column or be less than 0. This can be me
Résumé du contenu de la page N° 11
02 installing your dryer MOBILE HOME INSTALLATION The installation of the Dryer in mobile homes must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada). When installing a Dryer in a mobile home, you must make provisions for anchoring the dryer to the floor. Locate the dryer in an area that has
Résumé du contenu de la page N° 12
installing your dryer GAS REQUIREMENTS Use only natural or LP (liquid propane) gases. THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA). Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by
Résumé du contenu de la page N° 13
02 installing your dryer ELECTRICAL REQUIREMENTS A Wiring diagram is located on the back of the dryer. � Improper connection of the equipment grounding conductor can result in a risk of electric shock. WARNING Check with a qualified electrician or serviceman if you are in doubt as to whether your Dryer is properly grounded. Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician. � To prevent unnecessary risk o
Résumé du contenu de la page N° 14
installing your dryer ELECTRICAL CONNECTIONS Before operating or testing, follow all grounding instructions in the Grounding section. An individual branch (or separate) circuit serving only your Dryer is recommended. DO NOT USE AN EXTENSION CORD. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service, with a 15-amp fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require
Résumé du contenu de la page N° 15
02 installing your dryer Installation - General procedure For proper installation, we recommend that you hire a qualified installer. Read these instructions completely before you begin the installation. To install the dryer, follow these steps: 1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side- by-side so you have easy access to both appliances. To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer
Résumé du contenu de la page N° 16
installing your dryer 6. Review the Electrical Requirements section, then follow the 3 Wire Three Wire System system connection instructions (Step 7) or 4 Wire system instructions (Step 8) below. B W R 7. Three Wire system instructions: a. Loosen or remove the center terminal block screw. b. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Tighten screw. c. Connect the other wires to outer terminal block scr
Résumé du contenu de la page N° 17
02 installing your dryer U.S. MODELS: IMPORTANT – All U.S. models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block. Refer to the following instructions for 3- and 4
Résumé du contenu de la page N° 18
installing your dryer DRYER EXHAUST TIPS Plastic or non-metal flexible duct presents a potential fire hazard. WARNING 1. Make sure your dryer is installed properly so it exhausts air easily. 2. Use a 4” diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure the vent flap opens and closes freely. Inspect and clean the exhaust system annually. Don’t
Résumé du contenu de la page N° 19
02 installing your dryer DOOR REVERSAL 1. Unplug the power cord. 8. Reinsert the black screw in the other hole. 2. Remove two door hinge screws. 3. Lift the door and remove it. 4. Remove a screw on the 9. Reinsert the screw (Step Frame Front. 4) on the Frame Front. 5. Remove the two screws 10. Place the door on the on the opposite side of other side and reattach it the door hinge. to the dryer. 6. Remove two screws from 11. Reattach the holder lever. the holder lever. 7. Remove one black
Résumé du contenu de la page N° 20
installing your dryer CONNECTING THE INLET HOSE Method1 - Using the Y Connector and Long Hose The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. Turn off the cold water faucet. 2. If you have a washer water hose attached to the cold water Y-Connector faucet, unscrew and remove the hose. 3. If space permits, attach the brass female end of the “Y”connector to the cold water faucet. Turn by hand until tight. 4. Attach the straight end of the
