Résumé du contenu de la page N° 1
™
Diplomat
User Guide
PLEASE READ
INSTRUCTIONS
STORE UNDER
COVER
Résumé du contenu de la page N° 2
©2007 Britax Child Safety, Inc. All rights reserved. Printed in U.S.A P297700-R1:06.07 This product and its components are subject to change without notice.
Résumé du contenu de la page N° 3
Table of Contents Safety Information WARNINGS............................................................................ 2 Important Notes..................................................................... 4 Certification............................................................................ 5 Registration............................................................................ 5 Weight Range/Maximum Height............................................ 6 Installation: Aircraft.....
Résumé du contenu de la page N° 4
WARNING! DEATH or SERIOUS INJURY can occur: • Infants should remain in a rear-facing child restraint for as long a possible. The American Academy of Pediatrics and Britax recommends rear facing until at least 1 year of age and 20 pounds. • Use only with children who weigh between 5 and 40 pounds (2.3 and 18 kg.) and whose height is 40 inches (102 cm.) or less. Use rear facing for children 5–35 pounds (2.3–15.9 kg.) and forward facing to a maximum of 40 pounds (18 kg.). • Adjust the belts
Résumé du contenu de la page N° 5
• Based on crash statistics, the National Highway Traffic Safety Administration recommends that parents select the back seat as the safest location for a properly installed child restraint. Please study the Vehicle Safety Belts section in this booklet to ensure your child’s safety. If in doubt about installing child restraint, consult your vehicle’s owner’s manual. • Secure this child restraint even when it is not occupied. In a crash, an unsecured child restraint may injure vehicle occu
Résumé du contenu de la page N° 6
Safety Information Important Notes • Verify child restraint is secure and harness is properly adjusted around child each time child restraint is used. • Adjust harness to fit clothes the child is wearing. Remove bulky coats and/or jackets before putting child in restraint. • Cover restraint when vehicle is parked in direct sunlight. Parts of child restraint could become hot enough to burn a child. • Store child restraint in a safe place when it is not being used. Avoid placing heavy objects
Résumé du contenu de la page N° 7
Safety Information Certification This child restraint system conforms to all applicable Federal Motor Vehicle Safety Standards. This restraint is certified for use in motor vehicles and aircraft. Registration Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address, and the restraint’s model number and manufacturing date to Britax Child Safety, Inc., 13501 South Ridge Drive Charlotte, NC 28273, or call 1-88
Résumé du contenu de la page N° 8
Safety Information Weight Range Rear-Facing Weight 5-35 pounds (2.3-15.9 kg). Forward-Facing Weight 20 pounds (and 1 year) - 40 pounds (9-18 kg.) Maximum Height Rear-Facing The child is too tall when the top of the head is 1 inch from the top of the restraint. Forward-Facing Use of the restraint should be discontinued when any of the following occurs: • The top of the ears are above the top of the restraint • The top harness slots fall below the child’s shoulders • The child exceeds t
Résumé du contenu de la page N° 9
Safety Information Safety Information Safety Information Installation: Aircraft Aircraft Installation This child restraint is certified for aircraft use. Most airlines in the U.S. and Canada will allow use of a child restraint if it is labeled as an approved child restraint for airline use and fits properly on plane. Contact the airline about their policy prior to traveling. • The FAA recommends that a child weighing up to 40 pounds use a certified, harnessed child restraint while travel
Résumé du contenu de la page N° 10
Features 1 Cover 9 Infant Body Pillow 2 Headrest Adjustment 10 Chest Clip Knob 11 Harness 3 LATCH Adjuster 12 Harness Buckle 4 LATCH Release Button 13 Belly Pad 5 LATCH Connector 14 Harness Release Button 6 Headrest 15 Harness Adjuster Strap 7 Harness Slots 16 Recline Handle 8 Comfort Pads 8
Résumé du contenu de la page N° 11
Features 17�Forward-Facing Lock-Off 18�Rear-Facing Lock-Off 19�Base 20�Versa-Tether® Adjuster and Hook (inside pouch) 21�Belt Guard 22�Serial Number and Manufacturing Date (under cover) IMPORTANT: When not in use, this user guide should be stored under the cover. DO NOT discard foam inserts found under the cover. 9
Résumé du contenu de la page N° 12
Vehicle Compatibility Vehicle Safety Belts NOTE: The information in this section only applies to installation with vehicle safety belts. IMPORTANT: Vehicle seats and safety belts differ from vehicle to vehicle. Refer to your vehicle’s owner’s manual for specific information about vehicle safety belts and their use with child restraints. Some vehicles have no seating positions which are compatible with this child restraint or any A other child restraint. If in doubt, contact the vehicle m
Résumé du contenu de la page N° 13
Vehicle Compatibility Vehicle Seating Positions WARNING! Forward-facing vehicle seats MUST be used with this child restraint. Side-facing or rear-facing seats CAN- NOT be used. See diagram below. Vehicle Buckle Position WARNING! The position of vehicle belt buckle can affect stability of the child restraint. In a crash, an improperly positioned buckle could become loose and the child would be unprotected. If buckle lies near position marked as wrong ( ) when vehicle belt is tightened, try
Résumé du contenu de la page N° 14
Installation: Rear Facing LATCH Installation • Figure A illustrates a typical rear-facing LATCH installation. • Verify that your vehicle is equipped with LATCH anchors. If LATCH anchors are not available, you must use vehicle belt installation methods. NOTE: LATCH connectors must be in an upright position (as shown in figure B) and strap should be tight and not twisted to ensure proper installation. 1�If stored, remove LATCH connectors from storage slots A under cover (see page 28). 2�Pres
Résumé du contenu de la page N° 15
Installation: Rear Facing 7�Push child restraint firmly into vehicle seat while pulling each LATCH strap tight (fig. E). 8�Verify all connections are secure and that restraint is stable. The restraint is secure when it cannot be moved front-to-back or side-to-side more than 1” (2.5 cm.) at belt path. If restraint is not secure, repeat procedure, or use an alternate seating location or vehicle belt D installation method. • Britax recommends use of the Versa-Tether® to improve installati
Résumé du contenu de la page N° 16
Installation: Rear Facing Lap/Shoulder Belt Installation • Figure A illustrates a typical rear-facing, lap/shoulder belt installation. • When not in use, always store LATCH connectors in storage slots. (see page 28). 1�Fully recline restraint then place it rear facing on vehicle seat. 2�Lift cover to open rear-facing lock-off farthest from where vehicle belt will be buckled. A 3�Pull vehicle belt out then pass it through farthest rear-facing belt slot from where vehicle belt will be buc
Résumé du contenu de la page N° 17
Installation: Rear Facing 8�Verify all connections are secure and that restraint is stable. The restraint is secure when it cannot be moved front-to-back or side-to-side more than 1” (2.5 cm.) at belt path. If the restraint is not secure, repeat procedure or use an alternate seating location. • Britax recommends use of the Versa-Tether® to improve installation. See pages 23-26. E • The back angle of the child restraint should be 30º-45º from vertical (not to exceed 45º from vertical) when
Résumé du contenu de la page N° 18
Installation: Rear Facing Lap-Belt Installation • Figure A illustrates a typical rear-facing, lap-belt installation. • When not in use, always store LATCH connectors in storage slots. (See page 28). WARNING! Do not install with non-locking (ELR), 2-point vehicle belt. A 1� Fully recline restraint, then place it rear facing on vehicle seat. 2� Lift cover and open rear-facing lock-off farthest from where vehicle belt will be buckled. 3� Pull vehicle belt out, then pass it through farthes
Résumé du contenu de la page N° 19
Installation: Rear Facing 8� Verify all connections are secure and that restraint is stable. The restraint is secure when it cannot be moved front-to-back or side-to-side more than 1” (2.5 cm.) at belt path. If the restraint is not secure, repeat procedure or use an alternate seating location. • Britax recommends use of the Versa-Tether® to improve installation. See pages 23-26. • The back angle of the child restraint should be 30º-45º D from vertical (not to exceed 45º from vertical) when
Résumé du contenu de la page N° 20
Installation: Forward Facing LATCH Installation • Figure A illustrates a typical forward-facing LATCH installation. • Verify that your vehicle is equipped with LATCH anchors. If LATCH anchors are not available, you must use vehicle belt installation methods. NOTE: LATCH connectors must be in an upright position (as shown in figure B) and strap should be tight and not twisted to ensure proper installation. 1� If stored, remove LATCH connectors from storage slots A under cover (see page 28).
