Instruction d'utilisation Clam Corp Fish Trap X2 8237

Résumé du contenu de la page N° 1

M o d e l N o .

- 8 2 3 7 -


( p / n 1 0 8 3 2 6 )
S p e c i f i c a t i o n s
H e i g h t – 7 5 ” ( 2 5 ” p a c k e d )
▪
W i d t h - 7 5 i n c h e s
▪
▪ D e p t h – 9 0 ” ( 4 2 ” p a c k e d )
Weight - 1 4 5 l b s
▪
I n s t r u c t i o n p / n 1 0 2 4 8 3
▪


























- Clam Customer Servi ce Information -

NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE
A WARRANTY CLAIM, HAVE YOUR SALES RECEIPT READY

Résumé du contenu de la page N° 2

- Parts Diagram (Seating) – ITEM QTY P/N DESCRIPTION ITEM QTY P/N DESCRIPTION 1 8 101048 BLOCK, SLIDE 18 2 101813 BRACKET, RAIL HANGER 2 16 101081 WASHER, ¼ FLAT 19 2 101817 BRACKET, FRONT SEAT 3 34 101082 LOCKNUT, ¼” THIN 20 6 101829 ASSY, STRAIGHT CANOPY POLE 4 8 101088 SCREW, ¼” X ¾” PHILLIPS 21 2 101830 ASSY, BENT CANOPY POLE 5 4 101146 ANGLE, 1-1/2” X 1-3/4” X 9” ALUM 22 2 101836 ASSY, FRONT SPREADER POLE 6 8 101147 SCREW, #10 x 1” LONG PHILLIPS 23 2 101839 ASSY, ROOF SPREADER POLE

Résumé du contenu de la page N° 3

- Parts Diagram (Shelter) - 3

Résumé du contenu de la page N° 4

- Step 0ne - 4

Résumé du contenu de la page N° 5

- Step Two - 5

Résumé du contenu de la page N° 6

- Step Three - 6

Résumé du contenu de la page N° 7

- Step Four - Rear Seat Bracket (p/n 102430) Latch Clip (p/n 102512) 7

Résumé du contenu de la page N° 8

- Step Five - X2 Base (p/n 102500) 8

Résumé du contenu de la page N° 9

- Step Si x - 9

Résumé du contenu de la page N° 10

- Step Seven - 10

Résumé du contenu de la page N° 11

- Step Ei ght - X2 Tent (p/n 102437) 11

Résumé du contenu de la page N° 12

- Step Nine - 12

Résumé du contenu de la page N° 13

- Step Ten - 13

Résumé du contenu de la page N° 14

- Seating Installation - Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. With the latch clip hanging freely, tilt the complete assembly downward until the interior of the rear seat bracket surrounds the support tube. 14

Résumé du contenu de la page N° 15

- Seating Install ati on (cont .) - Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket. Secure the position of the latch clip by pushing it into the two holes located above the horizontal slot of the rear seat bracket. WARNING: ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE. FAILURE

Résumé du contenu de la page N° 16

- Tips for Use - Folding and transporting your Fish Trap is easy: Unsnap the roof spreader poles, rear spreader poles, and front spreader poles. Lay them in the ▪ bottom of the base. Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the ▪ front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. Cover with the Travel Cove