Résumé du contenu de la page N° 1
model g0656X
8" Jointer
w/spiral cutterhead
manual insert
t he Model g 0656X is the same machine as the Model g 0656, except it has a spiral cutterhead. Besides
the differences noted in this insert, all other content in the Model g 0656 owner's manual applies to this
machine. Before operating your new machine, you Must read and understand this insert and the entire
Model g 0656 manual to reduce the risk of injury when using this machine.
If you have any further questions about this manual i
Résumé du contenu de la page N° 2
4. When correctly set, the carbide insert will just inward touch the straightedge when the insert is at Mark its highest point of rotation (figure 2). 5 ⁄32" figure 4. straightedge inward mark at edge of outfeed table. figure 2. using a straightedge to align the outfeed table height with insert at tDC. 5. lock the outfeed table, reinstall the cutterhead guard, and close the rear access panel. —if your outfeed table is correctly set, no adjustments are necessary. replacing carbide ins
Résumé du contenu de la page N° 3
to rotate or change a carbide insert: note: Proper cleaning is critical to achieving a smooth finish. Dirt or dust trapped between 1. DisConnECt JointEr FroM poWEr! the insert and cutterhead will slightly raise the insert, and make noticeable marks on your 2. Move the cutterhead guard out of the way, or workpieces the next time you cut. remove it. 6. l ubricate the t orx screw threads with a 3. remove any sawdust from the head of the light machine oil, wipe the excess oil off the carbide i
Résumé du contenu de la page N° 4
MACHINE DATA SHEET MODEL G0656X 8" JOINTER w/SPIRAL CUTTERHEAD & MOBILE BASE Product Dimensions: Shipping Dimensions: Box #1 Box #2 Electrical: Motors: Main Main Specifications: Operation Information Model G0656X Page 1 of 2 -4- g 0656X Manual inser
Résumé du contenu de la page N° 5
Cutting Capacities Cutterhead Information Table Information Construction Other Infomation Other Specifications: Features: Model G0656X Page 2 of 2 -5- g 0656X Manual insert
Résumé du contenu de la page N° 6
t able parts breakdown -6- g 0656X Manual insert
Résumé du contenu de la page N° 7
t able parts l ist REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0452Z009 L-WRENCH TORX T20 47 PSB53M CAP SCREW M5-.8 X 18 2 P0452Z001 DRIVER BIT TORX T20 48 P0656048 SCREW SHAFT 4 PSS01M SET SCREW M6-1 X 10 49 PK69M KEY 4 X 4 X 12 5 P0656005 PULLEY 50 P0656050 SPACER 6 P0656006 RIGHT BEARING SUPPORT BLOCK 51 P0656051 BLOCK 7 P0656007 STUD 52 PRP49M ROLL PIN 5 X 25 8 PLW06M LOCK WASHER 10MM 53 P0656053 COLLAR 9 PN02M HEX NUT M10-1.5 54 P0656054 HANDWHEEL 10 P6204 BALL BEARING 6204ZZ 55 P06560
Résumé du contenu de la page N° 8
f ence parts breakdown -8- g 0656X Manual insert
Résumé du contenu de la page N° 9
f ence parts l ist REF PART # DESCRIPTION REF PART # DESCRIPTION 101 PS14M PHLP HD SCR M6-1 X 12 126 PSS01M SET SCREW M6-1 X 10 102 PW03M FLAT WASHER 6MM 127 P0656127 ADJUST LEVER 103 P0656103 HANDWHEEL 128 P0656128 SMALL BRACKET BLOCK 104 P0656104 BUSHING 129 P0656129 BRACKET BLOCK 105 PSS85M SET SCREW M6-1 X 45 130 P0656130 RIVET 2 X 4 106 PN01M HEX NUT M6-1 132 P0656132 FENCE 107 PB20M HEX BOLT M8-1.25 X 35 133 PSB13M CAP SCREW M8-1.25 X 30 108 P0656108 KNOB M10-1.5 134 PFH07M FLAT HD SCR M5
Résumé du contenu de la page N° 10
stand parts breakdown -10- g 0656X Manual insert
Résumé du contenu de la page N° 11
stand parts l ist REF PART # DESCRIPTION REF PART # DESCRIPTION 201 P0656201 CABINET 226-5 P0656226-5 JUNCTION BOX 202 PLN04M LOCK NUT M8-1.25 226-6 P0656226-6 S CAPACITOR 200M 250V 3-1/2 X 1-1/2 203 PW01M FLAT WASHER 8MM 226-7 P0656226-7 CENTRIFUGAL SWITCH 204 P0656204 WHEEL 226-8 P0656226-8 MOTOR CORD 14AWG X 3C 205 P0656205 SLEEVE 227 PK12M KEY 5 X 5 X 30 206 PB86M HEX BOLT M8-1.25 X 65 228 PVA50 V-BELT A-50 4L500 207 P0656207 PLASTIC GROMMET 229 P0656229 MOTOR PULLEY 208 PN08 HEX NUT 3/8-1
Résumé du contenu de la page N° 12
l abel placement 302 300 301 303 304 312 311 305 310 306 309 308 307 REF PART # DESCRIPTION REF PART # DESCRIPTION 300 P0656300 FENCE/CUTTERHEAD LABEL 307 P0656X307 MODEL NUMBER LABEL 301 P0656301 CUTTTERHEAD GUARD LABEL 308 G8588 SMALL GRIZZLY NAMEPLATE 302 PLABEL-14 ELECTRICITY LABEL 309 PPAINT-11 PUTTY TOUCH-UP PAINT 303 PLABEL-11 SAFETY GLASSES 2" X 3 5/16" 310 P0656X310 MACHINE ID LABEL 304 PLABEL-15 EAR PROTECTION 2" X 3-5/16"H 311 PPAINT-1 GRIZZLY GREEN TOUCH-UP PAINT 305 PLABEL-63 UNPLUG
Résumé du contenu de la page N° 13
MODEL G0656 8" JOINTER w/BUILT-IN MOBILE BASE MANUAL UPDATE This update covers changes made to the machine after the owner's manual was printed. All page num- ber references refer to the owner's manual for this machine. Keep this update with your owner's man- ual for future reference. If you have questions, contact Tech Support at (570) 546-9663 or by email at techsupport@grizzly.com. Machine Inventory (See Page 11) Clean Up (See Page 13) The fence assembly and fence bracket are no The followi
Résumé du contenu de la page N° 14
3. Remove the locking nut and flat washer 5. Install the round-slotted handwheel onto the (Figure 3) from the fence lock handle bolt right shaft with the 4 x 4 x 12 key, and install (Figure 4), place the fence assembly over the square-slotted handwheel onto the left the jointer tables and fence bracket, and shaft, using the cap screws and flat washers insert the bolt through the fence bracket slot, already mounted on the handwheel shafts. making sure the carriage fits over the key (Figure
Résumé du contenu de la page N° 15
MODEL G0656 8" JOINTER w/BUILT-IN MOBILE BASE OWNER'S MANUAL COPYRIGHT © NOVEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL10198 PRINTED IN CHINA
Résumé du contenu de la page N° 16
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������
Résumé du contenu de la page N° 17
Table of Contents INTRODUCTION ............................................... 2 Basic Controls .............................................. 20 Foreword ........................................................ 2 Stock Inspection & Requirements ............... 21 Contact Info ................................................... 2 Squaring Stock ............................................ 22 Machine Data Sheet ...................................... 3 Surface Planing .............................
Résumé du contenu de la page N° 18
INTRODUCTION Foreword Contact Info If you have any comments regarding this manual, We are proud to offer the Model G0656 8" Jointer please write to us at the address below: with Built-In Mobile Base. This machine is part of a growing Grizzly family of fine woodworking Grizzly Industrial, Inc. machinery. When used according to the guide- C /O Technical Documentation Manager lines set forth in this manual, you can expect P.O. Box 2069 years of trouble-free, enjoyable operation and Bellingham
Résumé du contenu de la page N° 19
Machine Data Sheet � � � � � � �� � � � �� � � � � � � � �� � � � �� �� � � � � �� � �� � � � � �� � � � � � � � �� �� � �� � � � � �� � � � � �� � � � � �� � � � � � � � �� �� � � �� � �� � � � � �� � � � � � � � � ������ ����� ��� �������� ��� ������� ���� �������� ����������� ������� ��������������������������������������������������������������� � ������������������������������������������������������������������������������������������������������������ ���� ���� � � �������������������� �
Résumé du contenu de la page N° 20
�������� ���������� ������ ��������� ����������������������������������������������������������������������������������������������������������������������������������� ����� �� ������ ��� ���� �������� ������ ��� ��� ��������������������������������������������������������������� � ����������������������������������������������������������������������������������� �� � �������� ������ ��� ���� ������������������������������������������������������������������������������������������������������