Résumé du contenu de la page N° 1
®
Product features may vary from the picture above.
Owner’s Manual with Assembly Instructions
Please read this manual and save it with your original sales receipt.
For Model 76950
Tools needed for assembly: Phillips and Slotted Screwdrivers, Hammer, Pliers and Safety Scissors.
® ®
Use only with a Power Wheels 6 Volt (4.0 Amp/hr.) Battery, Power Wheels 25 Amp Fuse
®
and Power Wheels 6 Volt Charger (all included).
CAUTION
ELECTRIC TOY: Not recommended for children under 1 year of age.
As with all
Résumé du contenu de la page N° 2
Table of Contents A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 3
Warnings B WARNING • Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. • Keep small parts and plastic bags out of children’s reach. Dispose of plastic bags properly. • Adult supervision is required. Children do not have the judgement necessary to avoid many accident
Résumé du contenu de la page N° 4
1 2 Parts C • If you experience a problem with this product or are missing a part, please call us at 1-800-348-0751 rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Front Wheel - 2 Vehicle Body Seat Base U-Cl
Résumé du contenu de la page N° 5
Parts Microphone Handgrip - 2 Footrest Support Footrest - 2 Key Assembly Front Axle - 2 Collar - 2 Steering Linkage Handlebar Wire Harness T-Slider Cap Nut - 7* Square Bushing - 3 Steering Column Battery Retainer 25 Amp Fuse - 2* Knob - 2 Round Bushing - 2 Not Shown: Label Sheet Lock Nut - 2 1 3 Washer - 2 #8 x / " Screw - 3 #10 x / " Screw - 2 2 4 7 1 1 #8 x / " Screw - 2 #8 x 1” Screw - 2 #10 x / " Bolt 8 #10 x 1 / " Bolt - 2 2 4 All Shown Actual Size *For your convenience, an extra cap nut an
Résumé du contenu de la page N° 6
1 2 Parts Diagram D 5 7 6 13 8 11 4 18* 34 26 3 12 20 16 2 14 16 32 15 9 10 1 19 8 22 23 8 37 24 26 36 27 31 35 25 30 28 17 21 29 8 33 1. Vehicle Body (with Base) 15. Grille 26. Washer - 2 7 2. Steering Column 16. #8 x / " Screw - 2 27. Square Bushing - 3 8 1 3. Handlebar 17. #10 x 1 / " Bolt - 2 28. Round Bushing - 2 4 1 4. Handgrip - 2 18. #10 x / " Bolt 29. Footrest - 2 2 5. Knobs - 2 (Not required for all models) 30. Footrest Support 1 6. Microphone 19. #8 x / " Screw 31. Front Wheel - 2 2 3
Résumé du contenu de la page N° 7
Battery Charging E WARNING • The battery must be handled by adults only. The battery is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in serious injury. • Never allow children to charge the battery. Battery charging must be done by adults only. A child could be injured by the electricity involved in charging the battery. • Use of the wrong type battery, fuse or charger could cause a fire or explosion, resulting in serious injury. ® ® • Use of Power Wheels comp
Résumé du contenu de la page N° 8
Battery Charging • Your new battery must be charged for at least 18 hours before you use it in your vehicle for the first time. 3 • We recommend that you start charging your battery before beginning assembly of your new vehicle. • The battery must be upright while charging. • Do not short circuit the battery. • You do not need to remove the battery from your vehicle to recharge it. ® • Use only a Power Wheels 6 volt charger (120 VAC 60 Hz 6W with an output of 6 VDC (400mA) to charge ® your Po
Résumé du contenu de la page N° 9
1 Assembly F Do Not Omit Any Steps U-Clip #1 1 3 Cap Nut Tab Peg Slot Collar Base Platform #1 Steering Linkage Base Front Axle Short Leg • Using safety scissors, separate the U-clips from the plastic connector. Dispose of the plastic connector. • The U-clips and base platforms are marked with a • Fit a collar, solid end first, onto the short leg of a “1” or a “2”. Note the markings on the U-clips and front axle. base platforms. • Fit a cap nut onto the end of the axle's short leg. • Snap the
Résumé du contenu de la page N° 10
Assembly 5 7 Wheel Bushing Cap Nut Round Bushing • Fit a wheel bushing into the rectangular opening in each front wheel. • Slide a round bushing onto the front axle and press it Wheel 6 into the center of the front wheel. Bushing Front Axle • Fit a cap nut onto the end of the front axle. • Tap the cap nut with a hammer to secure it on the front axle. • Repeat assembly steps 6 and 7 to assemble the other front wheel to the other front axle. • Position the vehicle body upright. Pegs Headlight 8 Wa
Résumé du contenu de la page N° 11
Assembly Handlebar Press Here 11 9 Handgrip Handgrip • Fit a handgrip onto each end of the handlebar. Helpful Hint: If the handgrips are difficult to slide onto the handlebar, moisten the handgrips with warm water before fitting them onto the handlebar. Handlebar 3 Wire Harness • Insert two #10 x / " screws through the slots in the 4 12 headlight and into the pegs in the handlebar. Connector Button End End • Press firmly on the front of the headlight and tighten each screw with a Phillips screwd
Résumé du contenu de la page N° 12
Assembly Headlight Steering Column 13 15 Handlebar Wire Harness Vehicle Square Body Opening Guides Handlebar • Insert the curved end of the steering column through the square opening in the vehicle body. • Turn the handlebar assembly upside down. 1 • Rotate the square bushing / turn to slide it over the 4 • Align the handlebar wire harness with the guides on the tabs on the steering column and into the square opening underside of the handlebar and the guide at the bottom in the vehicle body. of
Résumé du contenu de la page N° 13
Assembly Handlebar Wire Handlebar Harness 19 17 Cap Nut Connector Main Wire Harness Handlebar Connector Wire Harness Steering Column Hole Square Bushing Opening • Insert the wire connector on the main wire harness through the large opening in the center of the vehicle body. • Position the vehicle body upright. • Plug the main wire harness connector and the handlebar • While fitting the handlebar onto the end of the steering wire harness connector together. column, insert the end of the handleba
Résumé du contenu de la page N° 14
Assembly 21 23 T-Slider Grooves Footrest Footrest Support Support Bar Footrest Please Note: If you have not removed the protective foam • Insert the footrest support bar through the footrest pocket from the battery compartment, please remove it support at the bottom of the vehicle body. Make sure the and set it aside for later use. Remove any excess tape grooves on the footrest face up. from the vehicle and protective foam pocket and discard of the tape properly. • Align the holes in the other
Résumé du contenu de la page N° 15
Label Decoration G Proper label application will help to keep the labels looking their best! Temporary 3 • Please remove and discard the temporary labels Label adhered to the sides of the vehicle. 1 • Wash your hands before applying the labels. 9 • Make sure the areas where the labels will be applied are clean and dry. Wipe your vehicle with a clean, soft, dry 14 cloth to remove any dust or oils. • For best results, avoid repositioning a label once it has been applied to the vehicle. • Apply the
Résumé du contenu de la page N° 16
Résumé du contenu de la page N° 17
Battery Installation Tab 5 3 Tab Seat Tab Battery Connector Tab Motor Harness Connector • Plug the battery connector into the motor harness Lock connector. Fastener Note: If the battery connector will not plug into the motor harness connector, turn it over and try again! Do not force Tab the battery connector into the motor harness connector. 4 Lock Fastener Opening • Insert the tabs on the front of the seat into the slots in the vehicle body. Important Note: If the vehicle seat is equipped wit
Résumé du contenu de la page N° 18
Battery Installation Seat 7 6a Tab Lock Fastener Push Here Tab Lock Fastener • To recharge or change the battery, unlock the vehicle Lock Fastener seat: Opening - If your vehicle seat is equipped with a lock fastener, use 1 a slotted screwdriver to rotate the lock fastener /4 turn to the unlocked position ( ). 1 - If your vehicle seat requires use of the #10 x /2" bolt, loosen the bolt using a Phillips screwdriver. Remove the LOCKED bolt and set it aside for re-assembly of the seat. • Push in fi
Résumé du contenu de la page N° 19
Battery Care Battery Care and Disposal and Disposal I Care Disposal ® If a battery leak develops, avoid contact with the leaking • Your Power Wheels battery is a sealed lead-acid acid and place the damaged battery in a plastic bag. See battery. It must be recycled or disposed of in an environ- information below for proper disposal. mentally sound manner. If acid comes in contact with skin or eyes, flush with • Do not dispose of the lead-acid battery in your regular, cool water for at least 15
Résumé du contenu de la page N° 20
Rules for Safe Driving 6. Always wear shoes or sneakers when operating this Teach Safety Rules to Children vehicle. While children can quickly develop the skill necessary to 7. Never put anything near any moving parts. Rotating drive this vehicle, it is important to remember that their parts such as motors, gear boxes and wheels can snag judgement skills are still very immature. Unsupervised dri- fingers, hair, etc., causing serious injury. Do not allow ving by children can lead to serious injur
