Instruction d'utilisation Electro-Voice CPS 4

Résumé du contenu de la page N° 1

OWNER’S MANUAL

CPS 3 / CPS 4
CONTRACTOR PRECISION SERIES

Résumé du contenu de la page N° 2

IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance (servicing) instructions in the literature accompanying the a

Résumé du contenu de la page N° 3

DESCRIPTION CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Résumé du contenu de la page N° 4

FRONT PANEL 1. Level Control To prevent unauthorized operation of the level controls on the CPS3 and CPS4, they are provided with screwed-on protective cover lids. When shipped from the factory, the detented potentiometers are set to their clockwise limits. Thus, the input signal is not attenuated. In case matching the input levels is required, you first have to detach (unscrew) the cover lids to gain access to the potentiometers. 2. POWER ON INDICATION This LED lights up when the mains switch i

Résumé du contenu de la page N° 5

REAR PANEL POWER AMPLIFIER INPUTS Parallel to the XLR-type inputs, output connectors are provided, offering the opportunity to feed additional power amplifiers with the same signal. The inputs are electrically balanced with pin-assignment according to the IEC 268 standard. Pin-assignment of the XLR-type input connectors: PIN 1: SHIELD PIN 2: a, + PIN 3: b, - Input sensitivity is factory set to 0 dBu. The power amplifier can be set internally to +6dBu input sensitivity or to +2

Résumé du contenu de la page N° 6

REAR PANEL POWER AMPLIFIER OUTPUT CONNECTORS SPEAKON output connectors are provided for the power amplifier channels A (left) and B (right). The Bridged Out Connector for bridged operation is sealed with a plastic cover to prevent connection errors. LIMITER The time constant of the built-in limiter to avoid overdri- ving is adjustable. Position “SLOW” is the factory preset and this should also be the normal position. If the power amplifier is used as a MID/HI-frequency amplifier in active mult

Résumé du contenu de la page N° 7

SPECIFICATIONS Technical Specifications: CPS3, CPS4 Amplifier at rated conditions, both channels driven with 8 ohms loads, unless otherwise specified. CPS3 CPS4 Load Impedance 8 Ω 4 Ω 2 Ω 8 Ω 4 Ω 2 Ω Maximum Midband Output Power 560W 900W 1200W 850W 1300W 1800W THD=1%, 1kHz Rated Output Power 500W 800W 1000W 750W 1200W 1500W THD< 0.1%, 20Hz ... 20kHz Maximum Bridged Output Power 1800W 2400W ——— 2600W 3600W ——— THD=1%, 1kHz Maximum RMS Voltage Swing 72V 91V THD=1%, 1kHz Voltage Gai

Résumé du contenu de la page N° 8

BLOCK DIAGRAM 20

Résumé du contenu de la page N° 9

ABMESSUNGEN/DIMENSIONS Abmessungen/Dimensions (in mm) 21