Résumé du contenu de la page N° 1
FS-20
REMOTE CONTROL ALARM SYSTEM
OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of a Remote Alarm System by Crimestopper Security Products Inc. This
booklet contains the information necessary for installing, using, and maintaining your alarm system. If any
questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support
number below.
*IMPORTANT INFORMATION: Primary and Optional Features:
-PRIMARY: These are feat
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Operation Cautions & Warnings……..…………..…………………………………………………………….………2 The Remote Control…..……………………………...……………………..……………………….…….….…..……..3 . Operating Instructions………………………..……………….…….………………….…….…………...……….…4-7 Car Jack Protection..…………..…………..……………………………………………...…………………..…………8 Transmitter Programming.………………………………….…………………………….……………...…………..…9 2 Vehicle Programming…………..…………..………………….…………………………….…………….……..…..10 Battery Replacement…….…………………………………….....………………
Résumé du contenu de la page N° 3
THE REMOTE CONTROL Button Button Button Options Functions Lock Doors & Arm Press and hold 3 System Seconds for Panic Mode Unlock Doors and Unlock Doors and Disarm System Disarm System Press and Release for Trunk Release Aux # 1 Trunk Pop (Aux #1) Press and Release for Silent Arm / Disarm Aux Silent Arm. Press and #2 Hold for Aux #2 Selects between Vehicle LED Blinks while in #1 / Vehicle #2. Press & Side Button Vehicle 2 Mode Release
Résumé du contenu de la page N° 4
OPERATION INSTRUCTIONS ARMING To arm the alarm and lock the doors, press the Lock button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed. The red LED in the vehicle will start flashing after 5 seconds. After a short delay to allow vehicle and electronics to stabilize the system will be completely armed. DISARMING Press the Unlock
Résumé du contenu de la page N° 5
OPERATING INSTRUCTIONS ARM / DISARM WITH IGNITION ON (PROGRAM OPTION #15) This feature allows the system to be armed or disarmed while the ignition is in the ON position or vehicle is running. The feature is disabled by default and should not be used under normal operating conditions. On an installation with an add-on remote start module, this option can be enabled to allow the system to be armed or disarmed when the vehicle has been remote started (Ignition will be ON). Note that you
Résumé du contenu de la page N° 6
OPERATING INSTRUCTIONS EMERGENCY OVERRIDE / DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open the door with the key, which will activate the alarm. Turn the ignition on and press the override/program button for about 5 seconds (until siren stops). The Alarm will disarm. If you continue to hold the button for additional 7 seconds, the system will enter the Valet mode. EMERGENCY DISARM WITH CUSTOM OVERRIDE Custom
Résumé du contenu de la page N° 7
OPERATING INSTRUCTIONS VALET MODE (Solid LED) To disable the Alarm system for vehicle service or otherwise, turn the ignition on and press the override/program button 4-5 seconds until the dash LED turns on solid and you hear (1) siren chirp. Repeat the process to exit VALET mode and the system will chirp (2) times and the LED will turn off. Lock/Unlock and AUX features will still operate in when in VALET mode. When performing an Emergency Override and you hold down the override butto
Résumé du contenu de la page N° 8
CARJACK PROTECTION ACTIVE CARJACK This feature provides Active Carjack protection and must be enabled before use through Alarm programming option (14) See page 10. When the Ignition is on (vehicle is running), press and hold button #3 (AUX) for 3 seconds. Parking lights will flash TWICE to confirm the Carjack countdown sequence. LED begins to flash slowly. 90 Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a full system ac
Résumé du contenu de la page N° 9
TRANSMITTER PROGRAMMING NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes. 1. Turn key to the ON position and press program button 4 times. 2. After a short delay, the unit will flash the parking lights 4 times, Siren 4 times, Horn 4 times and status LED will be on solid. 3. Press the Lock Button on the remote you wish to program. 4. You should get 2 light flashes, 2 siren chirps and 2 horn honks (optional) indicating the unit is
Résumé du contenu de la page N° 10
2 VEHICLE OPERATION / PROGRAMMING 2 VEHICLE CONTROL Your remotes have the ability to control a second vehicle with a Crimestopper system installed. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 9) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing remotes. 2-VEHCLE NOTES: All Remotes for that vehicle must be learned at the time of programming. When you program your r
Résumé du contenu de la page N° 11
BATTERY REPLACEMENT To Replace the Batteries: The Remote Control uses Two CR-2016 Lithium 3 Volt Batteries. Simply remove the two Phillips screws holding the back cover in place. Insert the new batteries with the (-) end toward the circuit board. BACK COVER CR 2016 Lithium REMOVE SCREWS 11
Résumé du contenu de la page N° 12
2-Way DATA PORT Some vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module. Features Include • Tran
