Instruction d'utilisation Crimestopper Security Products CS-2001

Résumé du contenu de la page N° 1

CS - 2001








on your choice of a Gargoyle ™ Remote Alarm System by Crimestopper Security
Products Inc. This booklet contains the information necessary fo r installing, using, and maintaining your alarm
system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the



- PRIMARY: The se are features that must be connected in order for the system to operate properly i.e. Siren,


- These are features to be con

Résumé du contenu de la page N° 2

BEFORE BEGINNING , check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle. DO NOT EXCEED M AXIMUM OUTPUT RATINGS! - SERIOUS DAMAGE MAY OCCUR. LIMITS FOR ALARM FUNCTIONS ARE LISTED WHERE APPLICABLE. IF UNSURE ABOUT CURRENT LOAD, - METER. REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery a

Résumé du contenu de la page N° 3

SIREN MOUNTING: Mount the siren under the hood to fender - well or other body surface with the open end facing downward. Run the red siren wire through the firewall using a rubber grommet. Ground the black wire to the body LED Shock Se nsor: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with screws to firewall or side paneling. Override/Program Button: Mount the push - button in a hidden location easily accessible to the user in ca se

Résumé du contenu de la page N° 4

BLUE WIRE: ( - This wire is an input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that read g round when open. If no existing switches are available, install new pin switches. Note: DO NOT mount new GREEN WIRE: ( - Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some vehicles may have isolated door triggers. In this case you may need to run additional wires from other

Résumé du contenu de la page N° 5

GREEN: - RED: BLUE: - DETERMINING DOOR LOCK TYPE: We recommend determining the type of locking system the vehicle has before connecting any wires. Incorrect connection will result in damage to the r emote start and/or vehicle locking system. There are several types of door lock systems in vehicles today. Below is listed the many r Semi - - - NEG ATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING BLUE + BLUE L L POWER POWER LOCKING LOCKING REL RE

Résumé du contenu de la page N° 6

GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE + BLUE + 85 86 85 86 85 86 85 86 87 87 87 87 30 30 30 30 MASTER SWITCH + CUT L LOCK UL CUT UNLOCK DIP SWITCH PROGRAMMING - DOOR LOCK/UNLOCK PULSE TIME: - - LOCK WITH PASSIVE ARM: - ECT: 6 OFF= Alarm arms only with remote control. (Active) ON= Alarm arms automatically 30 Sec. after last door closed PASSIVE / ACTIVE ARMING SEL DIP SWITCH #4 OFF= Doors will not lock on Passive arming ON= Doors will lock

Résumé du contenu de la page N° 7

To change the electronic options turn the ignition on, wait at least (1) second, and press the override/program button 5 times. You will hear one 2 second long confirmation chirp from the siren. Within the next 5 seconds press the override/program button again the number of times that corresponds to the feature list below. The siren will chir p once for each button press. Press the #2 Unlock button on the transmitter to change the option from the default factory setting. 2 chirps

Résumé du contenu de la page N° 8

This setting changes the delay time in w hich the alarm system begins to monitor the Door, Hood, or Trunk Zones. This is helpful on vehicles with a delayed dome light to prevent the alarm from giving warning chirps due to the vehicle’s dome light staying on. Factory Default setting is 10 Sec. With this feature, the system can be programmed to Arm and Disarm without the siren chirp. Flashing parking lights will be the only Arm/Disarm confirmation. The Factory Default setting

Résumé du contenu de la page N° 9

4 BUTTON REMOTE TRANSMITTER: #2 #1 (UNLOCK) #4 #3 To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be disabled if these optional features are installed. The red LED in the vehicle will start flashing after 15 seconds. After a short delay to allow vehicle and electronics to stabilize the system w ill be completel

Résumé du contenu de la page N° 10

PRE - If a low - level shock to the vehicle body is detected, the pre - warning sensor activates sounding 6 quick siren chirps and 1 light flash. Adjust the shock sensor as needed by turning the control knob clockwise to increase sensitivity and - EME RGENCY OVERRIDE/DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open the door with the key, which will activate the alarm. Turn the ignition on and press the override

Résumé du contenu de la page N° 11

If the system detects a faulty or open zone (Door left open) when the system is armed, the siren will chirp 4 times along with 4 light flashes . The faulty zone will be automatically bypassed. The doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off. Doors IVE RE - - Active Re - arming means that the system will re - arm itself 30 seconds after disarmed with the transmitter if a door has not been opened. This is handy

Résumé du contenu de la page N° 12