Résumé du contenu de la page N° 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY HOME GYM
Hardware Pack
MWM-1100
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-1100
Retain This
Manual for
Reference
08-10-09
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
OWNER'S
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
MANUAL
info@impe
Résumé du contenu de la page N° 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 EXPLODED DIAGRAM………………………………………………………………………19 PARTS
Résumé du contenu de la page N° 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a ti
Résumé du contenu de la page N° 4
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the labels in the location shown. 3
Résumé du contenu de la page N° 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
Résumé du contenu de la page N° 6
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
Résumé du contenu de la page N° 7
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6
Résumé du contenu de la page N° 8
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Slide two Ø 2 ½” x 1” Rubber Bumpers (#35) onto the two Guide Rods (#5). Insert the two Guide Rods into the holes on the Rear Stabilizer (#2). Secure each Guide Rod with one M10 x 1” Allen Bolt (#62) and one ∅ ¾” Washer (#70) from
Résumé du contenu de la page N° 9
STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#50) onto the Guide Rods (#5). Make sure the deep groove on the Weight Plate are facing down and toward the back of the Machine. B.) Align the holes on the Weight Plates. Insert a Selector Rod (#16) through the center hole. Use the L-shaped Pin (#57) to select the number of Weight Plates for exercise. Each Plate weighted approx. 10lbs. Please refer to the Weight Resistance Chart in page 21. C.) Slide Selector Stem (#49) down the Guide Ro
Résumé du contenu de la page N° 10
DIAGRAM 2 9
Résumé du contenu de la page N° 11
STEP 3 (See Diagram 3) A.) Attach the Seat Support (#9) to the Vertical Frame (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#60), one 5 1/8” x 1 5/8” Bracket (#21), two Ø ¾” Washers (#70), and two M10 Aircraft Nuts (#72). B.) Place the Seat Pad (#25) onto the Seat Support. Secure it with two M8 x 2 3/8” Allen Bolts (#68) and two Ø 5/8” Washers (#69). C.) Attach two ∅ ¾” Leg Developer Bushings (#54) to the Leg Developer (#9). Attach the Leg Developer to the bracket on the Seat
Résumé du contenu de la page N° 12
STEP 4 (See Diagram 4) A.) Attach two Ø 1” x Ø ½” Bushings (#53) to the holes on Upper Frame (#4). Attach the Front Press Base (#6) to the two Bushings. Secure it with one M12 x 3 3/8” Hex Bolt (#61), two Ø 1” Washers (#71), and one M12 Aircraft Nut (#73). Do not over tighten the Nut and Bolt. B.) Insert the axle on the Right Butterfly (#8) through the hole on the Front Press Base from the bottom. Slide a Lock Ring (#41) onto the axle. Align the holes and secure it with one M6 x 1 3/8”
Résumé du contenu de la page N° 13
DIAGRAM 4 12
Résumé du contenu de la page N° 14
CABLE LOOP DIAGRAM 13
Résumé du contenu de la page N° 15
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 136” Upper Cable (#26) to the front opening on the Upper Frame (#4). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#38) to the forward most opening. Secure it with one M10 x 2 3/8” Allen Bolt (#64), two Ø 1” x ½” Pulley Bushings (#39), and one M10 Aircraft Nut (#72). C.) Draw the Cable towards the back of the machine to the second opening on the Upper Frame. Repeat Step B above to i
Résumé du contenu de la page N° 16
14 DIAGRAM 5 15
Résumé du contenu de la page N° 17
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 108” Butterfly Cable (#27) to the hook on the Right Butterfly (#8). Draw the Cable towards the right open Swivel Pulley Bracket (#17). B.) Attach a Pulley (#38) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#63), two ∅ ¾” Washers (#70), and one M10 Aircraft Nut (#72). C.) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double Floating Pulley Bracket (#18). Install a Pulley
Résumé du contenu de la page N° 18
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 142” Lower Cable (#28) to the opening on the bottom of the Leg Developer (#10). B.) Attach a Pulley (#38) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#64), two ∅ 1” x ½” Pulley Bushings (#39), and one M10 Aircraft Nut (#72). C.) Draw the Cable underneath the Pulley towards the back of the machine to the opening on the bottom of Vertical Frame (#3). D.) Repeat Step B to install a Pulley. E.) Pull the Cable
Résumé du contenu de la page N° 19
DIAGRAM 7 18
Résumé du contenu de la page N° 20
19
