Résumé du contenu de la page N° 1
REQUIRED TOOLS
AND MATERIALS:
Portable System
� 2 People
� Tape Measure
Owners Manual
Customer Service Center
� Wood Board
(scrap) • N53 W24700 South Corporate Circle � Sussex, WI 53089 � U.S.A.
� Sawhorse or
Support Table
� Tape
� Safety Glasses
� #3 Phillips
Screwdriver
� Needle-Nose Pliers
• (2 each) Wrenches
7/16" 1/2" 9/16" 3/4"
AND/OR
� Socket Wrenches and Sockets
(Deep-Well Sockets are
Recommended).
7/16" 1/2" 9/16" 3/4"
� Garden Hose or Sand
Write Model Number
WARNING!
From Box Here:
REA
Résumé du contenu de la page N° 2
BEFORE YOU START! WARNING Read and understand warnings listed below before using this product. Failure to follow these warnings may result in serious injury and/or property damage. Owner must ensure that all players know and follow these rules for safe operation of the system. � DO NOT HANG on the rim or any part of the system including backboard, support braces or net. � During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net.
Résumé du contenu de la page N° 3
HEIGHT ADJUSTMENT SAFETY INSTRUCTIONS CAUTION! DO NOT LET GO OF HANDLE FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY UNTIL THE RIM IS RESET AT RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND LOWEST POSTION OR WILL VOID WARRANTY. DESIRED HEIGHT. FAILURE TO FOLLOW THIS READ BEFORE Owner must ensure that all players know and follow these WARNING COULD RESULT OPERATING rules for safe operation of the system. IN SERIOUS INJURY AND/OR ELEVATOR PROPERTY DAMAGE. SYSTEM To ensure safety, do not a
Résumé du contenu de la page N° 4
NOTICE TO ASSEMBLERS Adult Assembly Required. Dispose of ALL packaging materials promptly. As with all products, periodically inspect for loose small parts. ALL basketball systems, including those used for DISPLAYS, MUST be assembled and installed according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift support system. WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT
Résumé du contenu de la page N° 5
Get to know the basic parts of your basketball system... FRONT VIEW BACKBOARD ELEVATOR ADJUSTMENT RIM POLE SUPPORT STRUT BASE 5 05/06 ID# M732211
Résumé du contenu de la page N° 6
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description Item Qty. Part No. Description 1 1 206657 Tank, (Black) 25 1 522730 Label, Height Adjustment and Moving 2 1 200628 Wheel Axle 26 1 Net 3 2 226401 Wheel, 4” (Black) 27 1 201160 Pawl Lever 4 1 908242 Top Pole Section 28 1 801159 Ratchet 5 1 908246 Middle Pole Section 29 2 900846 Backboard Bracket 6 1 908247 Bottom Pole Section 30 1 203472 Spring, Black, Slam Jam 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 31 1 200318 Bracket, Reinforcem
Résumé du contenu de la page N° 7
HARDWARE IDENTIFIER (BOLTS & PINS) Item #15 (2) Item #8 (1) Item #51 (4) Item #50 (2) Item #20 (4) Item #35 (1*) Item #34 (1) Item #11 (1) Item #42 (7) Item #49 (1) Item #36 (1) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #13 (1) Item #9 (2) Item #14 (1) Item #16 (8*) Item #38 (7) Item #18 (2) Item #39 (1) Item #12 (6) Item #23 (1) Item #37 (1) * You may have extra parts with this model. 7 05/06 ID# M732211
Résumé du contenu de la page N° 8
HARDWARE IDENTIFIER (STEEL SPACERS & RODS) Item #7 (1) Item #44 (2) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #33 (4) Item #41 (4) Item #45 (1) Item #17 (4) HARDWARE IDENTIFIER (OTHER) Item #40 (1) Item #31 (1) Item #30 (1) Item #32 (1) Item #52 (1) 8 ID# M732211 05/06
Résumé du contenu de la page N° 9
SECTION A: ASSEMBLE THE BASE ITEMS REQUIRED FOR THIS SECTION This is what your system will look like when you’ve finished this section. (2) 1/2” and (2) 9/16" Wrenches AND/OR (2) Socket Wrenches and Sockets 1/2” 9/16” Tape Correctly identify each pole section and mark indicated distance from ends with 1. tape as shown. TOP POLE 31” 4 5 MIDDLE POLE 43” 6 BOTTOM POLE 43” 9 05/06 ID# M732211
Résumé du contenu de la page N° 10
While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood 2. scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole. CAUTION! THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. IMPORTANT! Align dimple of top pole section (4) into
Résumé du contenu de la page N° 11
Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a wood scrap 3. as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. IMPORTANT! Align dimple of middle pole section (5) into trough of bottom pole section (6) CAUTION! as shown. THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-
Résumé du contenu de la page N° 12
6 Install rod (7) through holes in bottom pole section (6) and 4. eyebolt (8). 7 8 Install wheel axle (2) through wheel carriage (19) and 5. WARNING! install wheels (3) onto wheel axle (2) with spacers (17) as TWO CAPABLE ADULTS REQUIRED FOR THIS shown. Insert pole assembly into tank assembly as PROCEDURE. FAILURE TO shown. Secure bottom pole (6) section to tank and wheel FOLLOW THIS WARNING COULD RESULT IN SERIOUS carriage as shown. A deep socket is recommended. INJURY AND/OR PROPERTY DAMAGE
Résumé du contenu de la page N° 13
Secure base struts (10) to pole using bolt (11), washers (12), and nut (13), as 6. shown. Rotate the non-secured ends of base struts (10) as shown. 12 12 13 6 11 10 6 10 1 10 7. WARNING! Secure both base struts (10) to base using bolts (15), TIGHTEN BOLT (11) IN LOCK NUT (13) UNTIL FLUSH washers (12), and nuts (16). (EVEN) WITH LOCK NUT’S OUTER EDGE. 10 15 NOTE: 12 ORIENTATION OF STRUTS 10 15 12 12 1 16 12 16 13 05/06 ID# M732211
Résumé du contenu de la page N° 14
SECTION B: ATTACH THE BACKBOARD ITEMS REQUIRED FOR THIS SECTION This is what your system will look like when you’ve finished this section. (2) 1/2”, (2) 9/16” and (2) 3/4” Wrenches AND/OR NOTE: (2) Socket Wrenches and Sockets Board style will vary. 3/4” 1/2” 9/16” Fit spacer (44) into pawl (27). Then continue to 1. IMPORTANT! assemble as shown. Tighten completely. Test fit bolts into holes of brackets and carefully rock them in a circular motion to ream out paint from holes if necessary. 14 29
Résumé du contenu de la page N° 15
Identify elevator tubes (43). 43 2. Toward Toward Board Pole Elevator Tubes 3. Assemble elevator tubes (43) to ratchet (28) and backboard brackets (29) as shown. Tighten completely. IMPORTANT! LEVER IMPORTANT! BROOM Test fit bolts into holes of HANDLE brackets and carefully It is necessary for all parts to be installed rock them in a circular properly for this mechanism to work safely and motion to ream out paint properly. from holes if necessary. 27 38 29 41 45 38 43 23 17 41 28 42 17 42 43
Résumé du contenu de la page N° 16
Secure pawl (27) in place with clevis pin (34) and washers (18) as shown. 4. 18 27 34 18 Stretch spring (40) into position with pliers. 5. WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. 44 29 40 43 16 ID# M732211 05/06
Résumé du contenu de la page N° 17
Insert “T” bolt (36) through Slam Jam bracket (32) as shown. Secure Slam Jam bracket (32) and 6. backboard bracket (29) assemblies to backboard. Make sure rim spacer (52) is inserted into board. Bend upper halves of backboard brackets (29) to line up with holes in backboard and secure with bolts (50, 51) and nuts (16). Tighten completely. WARNING! USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJU
Résumé du contenu de la page N° 18
Attach upper elevator tubes (43) to backboard support brackets (29) using spacers (41), bolt 7. (42), and nut (38) as shown. 38 41 43 29 41 43 42 43 43 Support pole on sawhorse. Attach upper and lower elevator tubes (43) to upper pole section (4) 8. using bolts (42) and nuts (38) as shown. Attach pole cap (22) as shown. 38 38 43 4 22 43 42 42 18 ID# M732211 05/06
Résumé du contenu de la page N° 19
Attach outer handle tube (47) to upper elevator tubes (43) using bolt (42) spacers (33) and 9. nut (38) as shown. 42 33 47 43 33 38 Attach outer handle tube (47) to lower elevator tubes (43) using bolt (42) spacers (33) and 10. nut (38) as shown. 42 33 43 33 43 47 43 38 19 05/06 ID# M732211
Résumé du contenu de la page N° 20
Slide inner handle tube (48) into outer handle tube (47) as shown. 11. 47 48 Secure inner handle tube (48) to outer handle tube (47) using screws (20) as shown. 12. Slide handle (46) onto inner handle tube (48). 20 47 48 46 20 20 ID# M732211 05/06