Résumé du contenu de la page N° 1
Customer Service Center
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Sports Company
WRITE IN YOUR MODEL NUMBER: 1051
McCall's Rebounder
Owners Manual
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the
instructions care
Résumé du contenu de la page N° 2
McCall's REBOUNDER PARTS LIST (See Hardware Identifier) REBOUND ARM Item Qty. Part No. Description 1 1 200416 Base (Black) 2 4 200417 Casters 3 1 200419 Left Support Brace 4 1 201875 Right Support Brace HOPPER 5 1 200423 Outer Pole Assembly 6 1 201876 Inner Pole, Fixed Upright 7 1 201877 T-Screw 8 1 200418 Collar OUTER POLE 9 1 200421 Winch Handle 10 1 200409 Cable Assembly 11 1 200410 Winch COLLAR WINCH 12 1 201878 Graduated Scale 13 1 201879 Indicator Bracket 14 1 201888 Rebound/Tip-in Indic
Résumé du contenu de la page N° 3
HARDWARE IDENTIFIER Item #7 (1) Item #20 (8) Item #21 (1) Item #22 (18) Item #19 (1) Item #23 (2) Item #24 (1) Item #25 (2) Item #26 (3) Item #27 (16) Item #29 (8) Item #30 (4) Item #31 (18) Item #28 (1) Item #32 (4) Item #33 (4) 3 12/02 P/N 211670
Résumé du contenu de la page N° 4
SECTION A : ASSEMBLING THE McCALL'S REBOUNDER Tip base on it's side and install casters (2) to the bottom of base (1) as shown 1. using bolts (22), lockwashers (31) and nuts (27). 22 31 27 WARNING 2 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. Attach collar (8) to outer pole (5) as shown with T-Screw bolt (7). Tighten 2. completely. NOTE: THE T-SCREW (7) IS USED TO SECURE 6 COLLAR TO OUTER POLE (5) UNTIL STRUTS ARE ATTACHED (STEP 4)
Résumé du contenu de la page N° 5
Attach pole assembly (5 & 6) to base (1) using bolts (20) and lockwashers (29) as 3. shown. WARNING 29 TWO PERSON MINIMUM 20 REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. Attach left (3) and right (4) support braces to base (1) and then adjust collar (8) to 4. accommodate strut height. Attach braces (3 & 4) using bolts (20) and lockwashers (29) as shown . 20 29 25 3 20 29 4 25 29 20 4 3 5 12/02 P/N 211670
Résumé du contenu de la page N° 6
2 1 12 12 1 11 1 1 10 0 9 Attach graduated scale (12) to base (1) using bolt (21) and lockwasher (30) 5. as shown. 12 21 30 1 Attach graduated scale (12) to bracket affixed to the collar (8) as shown with nuts 6. (25) and lockwashers (30). 25 8 30 12 6 P/N 211670 12/02 4 3 2 1 7 11 4 10 3 2 1 7 11 11 10 10
Résumé du contenu de la page N° 7
2 1 12 12 1 11 1 10 10 9 2 1 12 12 1 11 1 1 10 0 9 Attach winch assembly (9, 10 & 11) to collar bracket using nut (25) and lockwasher 7. (30) as shown [Winch components (9, 10 & 11) are preassembled]. TOP 10 IMPORTANT: DO NOT ATTACH TOP NUT. ATTACH BOTTOM NUT 9 ONLY. 11 30 25 IMPORTANT: CORD MUST PASS BEHIND BOTTOM SPACER AS SHOWN! Release the lever and unwind cable and attach top nut (25) and lockwasher (30) 8. to fully secure winch assembly to collar bracket as shown. Locked 30 25 Released WAR
Résumé du contenu de la page N° 8
Hook Indicator Bracket (13) around the Graduated Scale (12). Do not attach 9. Rebound/Tip-in Indicator (14) yet, or the bracket will not fit around scale. 12 13 12 13 Attach Rebound/Tip-in Indicator (14) to indicator bracket (13) while holding bracket 10. (13) in the position shown. The bracket/tip-in assembly (13 & 14) will not be secured until the next step (#11). 14 22 12 13 14 13 8 P/N 211670 12/02
Résumé du contenu de la page N° 9
Attach unwound cord to indicator bracket (13) and bracket on outer pole (5) 11. using nut (24) and lockwasher (28) as shown. 10 14 5 13 28 6 24 NOTE: THIS STEP FUNCTIONS TO RAISE THE OUTER POLE TO ACCOMMODATE THE DIFFERENT HEIGHTS DENOTED ON THE TIP-IN INDICATOR. 9 12/02 P/N 211670
Résumé du contenu de la page N° 10
Turn hopper (15) upside down and attach air checks (18) as shown by removing 12. and then re-inserting the retaining (33) and clevis (32) pins connected to the air checks (18). 23 23 NOTE: ITEMS (34 & 23) COME PREASSEMBLED TO THE HOPPER (15) BUT CAN BE REPLACED AND ORDERED SEPARATELY. 18 16 34 33 33 32 32 10 P/N 211670 12/02
Résumé du contenu de la page N° 11
Place (2) 100 lb. sand bags (not included) into storage bags (35). Add bags to the 13. base as shown. IMPORTANT! DO NOT EMPTY SAND FROM SAND BAGS INTO THE STORAGE BAGS. PLACE SEALED SAND BAGS COMPLETELY INTO STORAGE BAGS. 35 14 Slide Hopper assembly (15) over the top of the pole (5) tighten bolts indicated. 15 16 Tighten completely 9/16" wrench needed 5 WARNING THE HOPPER IS HEAVY! TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. DO NOT LE
Résumé du contenu de la page N° 12
SECTION B : OPERATING THE McCALL'S REBOUNDER BALL-CHECK MECHANISM - STANDARD POSTION 1. 1. Ball-Check Mechanism (17) holding ball. 2. For normal operation, pull down on Rebound Arm (16) which causes Ball-Check Mechanism (17) to drop, allowing ball to pass to arm. 3. Ball in arm position with Ball-Check Mechanism (17) holding next ball. 17 16 NOTE: IF THE REBOUND ARM IS RETURNING TOO FAST, OR IS 18 Adjustment screw location RETURNING TOO SLOW, THE AIR CHECKS (18) MAY HAVE TO BE ADJUSTED ACCORDIN
Résumé du contenu de la page N° 13
2 1 1 12 2 1 11 1 10 10 9 SECTION C : ADJUSTING THE HEIGHT 1. Adjust height by unlocking the winch lever (fig. A) and turning handle (9). Set winch lever back to the locked position (fig. B) when desired height is attained. 9 WARNING HOLD ONTO HANDLE BEFORE UNLOCKING. THE WEIGHT OF THE HOPPER AIDS IN THE LOWERING OF THE HEIGHT. LOCKED UNLOCKED Fig. A Fig. B 13 12/02 P/N 211670
