Résumé du contenu de la page N° 1
Owner’s
Manual
Model C4492 and H0127
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
T TABLE OF CONTENTS ABLE OF CONTENTS Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Assembly Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 4
IMPORTANT INFORMATION IMPORTANT INFORMATION • Please keep this Owner’s Manual for future reference, as it contains important information. • Adult assembly is required. You may need the assistance of another adult to complete assembly. 1 2 • Approximate assembly time is 2 / -5 hours. We recommend the use of a power screwdriver to reduce assembly time. TM • Be sure to assemble the GameStation in the room it is intended to be used. TM Do not use the GameStation in a room with direct sunlight. Do
Résumé du contenu de la page N° 5
WARNING CHOKING HAZARD – Toy contains a small ball (golf ball). Not for children under 3 years. CAUTION This product contains small parts in its unassembled state. Adult assembly is required. 4
Résumé du contenu de la page N° 6
PA PAR RT TS S 1 2 L Tubes (Left and Right) x 2 2 2 Crossbars 1 3 2 Bases (Left and Right) 4 2 Lower Net Clips 5 Putting Green 2 6 Goal x 2 7 Wire Clip 8 2 Net Tubes (1A, 1B) 9 2 Net Tubes (2A, 2B) 10 2 Net Tubes (3A, 3B) 11 2 Feet 12 2 Nets 3 4 5 13 Chute 14 2 Chute Tubes (4A, 4B) x 2 15 Ball Sensor 16 2 Plugs 17 Support Tubes 18 Game Selector 19 Retainer 20 2 Upper Net Clips 21 Backboard 22 Scoreboard 23 Backboard Tube Left Right 24 Rim 6 7 8 9 10 11 x 2 x 2 x 2 x 2 5
Résumé du contenu de la page N° 7
13 12 x 2 14 15 16 x 2 x 2 17 18 19 20 21 x 2 x 2 22 23 24 6
Résumé du contenu de la page N° 8
PA PAR RT TS S 25 26 27 25 Handle Tubes 26 Handle x 2 27 Handle Pivots 28 Connector Cover 29 2 Wire Covers 30 5 Wire Ties x 2 31 2 Chute Tabs 32 Shaft 28 29 30 33 Blade 34 Flag x 2 35 Target 36 Putter 37 2 Basketballs 38 2 Footballs 39 2 Baseballs 33 34 40 Puck 31 32 41 Soccer Ball 42 Golf Ball x 2 35 36 Tip: Add the flag in the Game Setup section. Tip: Add the 37 38 39 target in the Game Setup x 2 x 2 x 2 section. Tip: For Model H0127, there are three extra balls (one basketball, one footb
Résumé du contenu de la page N° 9
F FASTENERS ASTENERS Tip: All fasteners shown actual size. M5 x 29 mm Bolt – 20 M5 Lock Nut – 16 M5 x 75 mm Bolt – 2 #8 x 37 mm Screw – 8 #8 x 15 mm Screw – 25 M6 x 35 mm Bolt – 8 M6 Lock Nut – 8 These lock nuts are not located in a parts bag. They are fitted inside various plastic parts. Note: Tighten and loosen all bolts and screws with a Phillips screwdriver. Do not over-tighten the fasteners. We’ve included extra fasteners for your convenience! 8
Résumé du contenu de la page N° 10
BA BAT TTERY INST TERY INSTALLA ALLATION TION Tip: We recommend the use of alkaline batteries for longer battery life! 1.5V x 4 "C" (LR14) Battery Compartment Door SHOWN ACTUAL SIZE • Loosen the screws in the battery compartment door on the back of the scoreboard. Remove the battery compartment door. • Insert four "C" (LR14) alkaline batteries. • Replace the battery compartment door and tighten the screws. TM Tip: When sounds or lights from the GameStation become faint or stop, it’s time for an
Résumé du contenu de la page N° 11
ASSEMBL ASSEMBLY TIP Y TIP • When tightening bolts in tubes, you will need to press the lock nut into the opposite side of the tube (the hex hole). Place your thumb on the lock nut while tightening bolt with a Phillips screwdriver. Tip: You may want to use an adjustable wrench to hold the lock nut in place. 10
Résumé du contenu de la page N° 12
DECORA DECORATION TION • Before applying the labels, wipe the surface of the scoreboard, backboard, game selector, target and putting green with a clean, dry cloth to remove any dust or oils. • Apply the labels as indicated in the illustrations. 1 3 6 Points Overtime Strikeouts Pitches 4 7 Down Attempts 8 5 50 40 30 20 10 TD 12 3 balls strikes 1 2 outs 2 To Play VOLUME 3 10 (Model C4492) 9 (Model C4492) Press Start START BASKETBALL BASEBALL 2 FOOTBALL Select Sport HOCKEY SOCCER 6(Model H0127) 8
Résumé du contenu de la page N° 13
Model C4492 4 7 5 2 6 Model H0127 10 2 5 3 99 4 12
Résumé du contenu de la page N° 14
ASSEMBL ASSEMBLY Y L Tube L Tube White Dots Crossbar STEP 1 • Position the L tubes on either side of a crossbar, as shown. Tip: The L tubes are slightly different! One of the L tubes has a white dot on the lower portion. •Match the white dot on the crossbar with the white dot on the L tube. 13
Résumé du contenu de la page N° 15
M5 x 29 mm Bolts M5 Lock Nuts STEP 2 Tip: You will need to lean the assembly against a wall or an object to complete this step. • Insert an M5 x 29 mm bolt through the outside of the L tube. • Fit an M5 lock nut, rounded side out, to the matching hex hole in the crossbar. Rounded • While holding the lock nut in place, tighten the bolt. Side • Fit another M5 lock nut and M5 x 29 mm bolt to the crossbar and L tube and tighten. Tip: If you cannot attach the M5 lock nut to the end of the M5 x
Résumé du contenu de la page N° 16
ASSEMBL ASSEMBLY Y M5 Lock Nuts M5 x 29 mm Bolts STEP 3 Rounded Tip: You will need to lean the assembly against Side a wall or an object to complete this step. • Insert an M5 x 29 mm bolt through the outside of the other L tube. • Fit an M5 lock nut, rounded side out, to the matching hex hole in the crossbar. • While holding the lock nut in place, tighten the bolt. • Fit another M5 lock nut and an M5 x 29 mm bolt to the crossbar and L tube and tighten. 15
Résumé du contenu de la page N° 17
Lower Net Clip Base Slot STEP 4 • Fit the lower net clip into the slot in one of the bases. 16
Résumé du contenu de la page N° 18
ASSEMBL ASSEMBLY Y Lower Net Clip #8 x 15 mm Screws STEP 5 • Insert three #8 x 15 mm screws into the lower net clip and tighten. • Repeat assembly steps 4 and 5 to assemble the other lower net clip to the other base. 17
Résumé du contenu de la page N° 19
Lower Net Clip Left Base Hockey Stick Storage STEP 6 • With the lower net clip facing out, slide the left base onto the tube assembly, as shown. Tip: The left base includes a hockey stick storage area. 18
Résumé du contenu de la page N° 20
ASSEMBL ASSEMBLY Y Right Base Lower Net Clip STEP 7 • With the lower net clip facing out, slide the right base onto the tube assembly, as shown. 19
