Résumé du contenu de la page N° 1
CORD REEL WORK LIGHT
(30 FOOT, FLUORESCENT)
Model 92156
ASSEMBLY AND OPERATING INSTRUCTIONS
®
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Fre
Résumé du contenu de la page N° 2
PRODUCT SPECIFICATIONS Cord Length 30 Feet (16 Ga.) Maximum Bulb Wattage 13 Watts Outlet Capacity 5 A/125 VAC Weight 7.3 Lbs. E223040 Features: 4’ Pigtail with overload protection, 13 Watt Fluorescent Bulb, 3- Prong Socket in Handle, GENERAL USE CORD REEL ONLY FOR USE IN INDOOR DRY LOCATIONS ONLY SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and as- sembly diagram. Keep your i
Résumé du contenu de la page N° 3
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Double insu
Résumé du contenu de la page N° 4
12. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. 14. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection
Résumé du contenu de la page N° 5
23. When servicing a reel, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Cord Reel Work Light. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Always wear ANSI approv
Résumé du contenu de la page N° 6
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet insta
Résumé du contenu de la page N° 7
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGURE B EXTENSIO
Résumé du contenu de la page N° 8
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NA
Résumé du contenu de la page N° 9
UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 12 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 13. 1. CAUTION: Always make sure the Power Cord of the Cord Reel Work Light is unplugged from its electrical
Résumé du contenu de la page N° 10
OPERATING INSTRUCTIONS 3. Hang the Cord Reel Work Light and plug it in to an outlet. 4. Pull on the Cord until it reaches the desired length and then let it slightly retract until it locks into place. 5. You may slide the Hook (25) along the Cord to hang the Cord, keeping it out of the way. Also, you may use the Hook (21) to hang the Cord Reel Work Light, allowing for hands free operation. See FIGURE 1. 6. To turn on the light, press the Switch (29) to the “I” position (see FIGURE 1). To turn
Résumé du contenu de la page N° 11
INSPECTION, MAINTENANCE, AND CLEANING (cont’d) 4. Check the Cord for frays, tears, or cracks. Have the Cord replaced by an autho- rized technician if necessary. 5. To change the Bulb (31): • Remove the Clear Cover (15) by removing the Screws (16) and gently pulling it off. See FIGURES 3 and 4. • Remove the Bulb Protector (27) from the old Bulb. Gently fit the Bulb Protec- tor (27) over the new Bulb (31). See FIGURE 5. • Gently snap the new Bulb (31) into the receptacle. See FIGURE 6. • Repl
Résumé du contenu de la page N° 12
PARTS LIST Part Description 1 Left Cover 2 Ratchet Pawl 3 Gear 4 Plate 5 Spring 6Drum 7Drum 8 Positive Plate 9 Negative Plate 10 Loop 11 Bracket 12 Right Cover 13 Bracket 14 Circuit Breaker 15 Clear Cover 16 Screw (2 Qty.) 17 Screw (5 Qty.) 18 Left Housing 19 Lamp Ballast 20 Stop Ball 21 Hook 22 Socket 23 Built-in Socket 24 Hook Connector 25 Hook 26 Rod 27 Bulb Protector 28 Right Housing 29 Switch 30 Reflector 31 Bulb (110V, 13 Watt) 32 Cord Clamp PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACT
Résumé du contenu de la page N° 13
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 92156 For technical questions, please call 1-800-444-3353. Page 13
