Instruction d'utilisation Chicago Electric Auto Darkening Welding Helmet 67854

Résumé du contenu de la page N° 1

Résumé du contenu de la page N° 2

SAFETY SPECIFICATIONS OPERATION MAINTENANCE Table of Contents Safety ......................................................... 3 Maintenance ............................................... 9 Specifications ............................................. 5 Parts List and Diagram .............................. 10 Operation .................................................... 6 Warranty .................................................... 12 WARNING SYMBOLS AND DEFINITIONS This is the safety alert sy

Résumé du contenu de la page N° 3

IMPORTANT SAFETY INFORMATION When using helmet, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Read all instructions before

Résumé du contenu de la page N° 4

SAFETY SPECIFICATIONS OPERATION MAINTENANCE 13. This helmet provides protection for intended c. Regularly replace the Front Lens Cover purposes only. There are certain applications if it becomes cracked, scratched, for which this helmet was designed. Do not pitted, or otherwise damaged. modify this helmet and do not use this helmet d. Do not make any modifications to either the Auto- for a purpose for which it was not intended. Darkening Filter or the rest of the helmet, other a. The Welding

Résumé du contenu de la page N° 5

Specifications Description Auto-Darkening Welding Helmet Power Source Solar powered cells with battery assistance (not rechargeable) Operating Temp. 23° to 131° F Resting Shade Shade # 4 Shade Range 9 to 13 UV/IR Protection up to DIN 16 at all times Lens Type ANSI Z87.1-2003 approved V iewing Area 3.86" x 1.73” Welding Protection For Processes including MIG/Flux welding, stick Types welding, TIG welding (10+ amps), plasma arc welding/cutting and air carbon cutting. Not for Laser Welding or

Résumé du contenu de la page N° 6

11 10 SAFETY SPECIFICATIONS OPERATION MAINTENANCE 9 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Function The Auto-Darkening Welding Helmet is designed to protect the eyes and face from sparks, splatter, and harmful radiation under normal welding conditions. The Auto-Darkening Filter automatically changes from a clear state to a dark state when an

Résumé du contenu de la page N° 7

Adjusting Headband Solar Cells Adjust the Headband so that the helmet This Welding Helmet utilizes high performance solar is seated securely on your head as low cells as power supply , and has two built-in 3V lithium as possible and close to your face. batteries as power backup. No change of battery is needed. Under normal welding conditions, users can Adjust the Headband width by turning the expect a battery lifetime of more than 6 years. Ratcheting Headband Knob to make sure the Front Co

Résumé du contenu de la page N° 8

SAFETY SPECIFICATIONS OPERATION MAINTENANCE Common Problems and Remedies 1. Irregular Darkening Or Dimming a. Headband has been set unevenly on both sides of helmet (unequal distances from the eyes to filter’s lens). b. Reset Headband to reduce dif ference in distances to filter , if necessary . 2. Auto-Darkening Filter Does Not Darken Or Flickers a. Front Cover Lens is soiled or damaged (change the cover lens). b. Sensors are soiled (clean surface of the sensors). c. Welding current is too low

Résumé du contenu de la page N° 9

Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Lens and Helmet Maintenance Replace the Front Lens Cover if it is damaged Figure F (cracked, scratched, soiled or pitted). 1. To Replace the Cover: a. Remove the Front Lens Cover by gently pulling up th

Résumé du contenu de la page N° 10

SAFETY SPECIFICATIONS OPERATION MAINTENANCE Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PROVIDED THE P AR TS LIST AND ASSEMBL Y DIAGRAM IN THIS MANUAL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF ACTURER OR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE IS QUALIFIED T O MAKE ANY REP AIRS T O THE PRODUCT , OR THA T HE OR SHE IS QUALIFIED T O REPLACE ANY P

Résumé du contenu de la page N° 11

Assembly Diagram Item 67854 For technical questions, please call 1-800-444-3353. Page 11 d n i r G MAINTENANCE OPERATION SPECIFICATIONS SAFETY

Résumé du contenu de la page N° 12

Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installatio