Résumé du contenu de la page N° 1
Weather Forecaster
with Indoor/Outdoor
Temperature and
Humidity
USER MANUAL
(TE529ELW)
1 1
Résumé du contenu de la page N° 2
INTRODUCTION PRODUCT OVERVIEW Thank you for selecting the Honeywell Weather MAIN UNIT Forecaster. This device includes weather forecast with FEATURES pressure trend, precise time keeping and • Wireless sensor transmits temperature and humidity to the temperature and humidity monitoring features main unit from up to 100 feet away • Multi-channel capability to monitor temperature and that you can use from the comfort of your home. humidity in up to 3 remote locations In this package you wi
Résumé du contenu de la page N° 3
A WEATHER AND PRECISE TIME INFORMATION IN FIVE - LINE LCD DISPLAY Views indoors and outdoors conditions along with precise time H B MEMORY BUTTON A 1). Recalls current, maximum or minimum temperature and humidity ATO M I C C LO C K 2). Clears all readings memory C MODE BUTTON Changes clock display modes, activates and confirms settings D ALARM ON/OFF BUTTON Sets weekday, single and pre-alarm and allows displaying alarm status E UP BUTTON 1). Increases settings 2).
Résumé du contenu de la page N° 4
REMOTE SENSOR FEATURES • Remote temperature transmission to the main unit via 433 MHz signal I • Case can be wall mounted using built-in hanger • 100 feet transmission range without interference • LCD display of measured temperature and humidity • Temperature display type (C°or F°) selection • Transmission channel selection E 1 2 3 MADE IN CHINA A F C D J B TM THERMO – HYGRO SENSOR K MADE IN CHINA A LED INDICATOR Flashes once when the remote sensor transmits the reading REAR
Résumé du contenu de la page N° 5
E WALL-MOUNT RECESSED HOLE only one remote sensor is being used. Keeps the remote sensor on the wall 3. If you are using more than one sensor, select a different channel for each sensor. F °C/ °F SWITCH 4. Install two “AA” size alkaline batteries (not included) Selects the temperature display unit in Celsius or Fahrenheit matching to the polarities shown in the battery compartment. 5. Replace the battery compartment door and secure the screws. 6. Secure the remote sensor in the d
Résumé du contenu de la page N° 6
CHECKING REMOTE AND INDOOR TEMPERATURES * Make sure the main unit is positioned at 8 feet minimum distance from any interference source such as a TV, The wave icon on the main unit's display located near the remote sensor reading line, indicates a good reception from computer monitor, microwave, etc. The successful reception of the atomic time signal depends on the positioning and the remote sensor. If the temperature goes above or below the temperature operating range stated in specific
Résumé du contenu de la page N° 7
TEMPERATURE AND HUMIDITY SCANNING Indicator Shows Press and hold CHANNEL button for 2 seconds Temperature Humidity displayed Current – the indoor, channel 1, channel 2 and 3 readings will be Range Range on the unit Environment displayed in sequence automatically. Ideal range for LOST COMMUNICATIONS 20˚C to 25˚C 40%RH- both relative If the main unit display for the remote sensor goes blank, COM (68˚F to 77˚F) 70%RH humidity and press and hold [ ] button for 2 seconds to begin a new signal tem
Résumé du contenu de la page N° 8
TRANSMISSION COLLISION SETTING CLOCK MANUALLY TIME ZONE Signals from other household devices, such as doorbells, home security systems, and entry controls, may interfere 1). Press MODE to select HOUR/MINUTE/WEEKDAY display. with this product and may cause temporary reception failure. This is normal and will not affect the general 2). Press and hold “UP” button for 3 seconds to enter into TIME ZONE display mode. performance of the product. The transmission and reception of temperature readi
Résumé du contenu de la page N° 9
SNOOZE PRECAUTIONS When the alarm sounds, press the SNOOZE/LIGHT button This product is engineered to give you years of satisfactory to temporarily stop the alarm. After depressing service if handled carefully. Here are a few precautions: SNOOZE/LIGHT button, the alarm sound will resume in 1. Do not immerse the units in water. 5 minutes. If the alarm is not disabled after that, it will sound 2. Do not clean the units with abrasive or corrosive materials. for 4 more minutes and then will stop
Résumé du contenu de la page N° 10
FCC STATEMENT Remote Sensor This device complies with Part 15 of the FCC Rules. Temperature Operation is subject to the following two conditions: Proposed operating range (1) This device may not cause harmful interference, and with alkaline batteries : -20°C to + 70°C / (2) This device must accept any interference received, -4°F to 158°F including interference that may cause undesired operation. Proposed operating range with lithium batteries : - 38°F to 158°F Warning: Changes
Résumé du contenu de la page N° 11
DECLARATION OF CONFORMITY STANDARD WARRANTY INFORMATION This product is warranted from the manufacturing defects for We one year from date of retail purchase. It does not cover damages or wear resulting from accident, misuse, abuse, Name: Hideki Electronics, Inc. commercial use, or unauthorized adjustment and repair. Address: 7865 SW Mohawk, Tualatin, OR 97062 Telephone No.: 1-503-612-8395 Note that online product registration is required to ensure valid warranty protection. declare that the pro
