Résumé du contenu de la page N° 1
LBI-38901E
Installation Manual
™
Orion Mobile Radio
ericssonz
Résumé du contenu de la page N° 2
TABLE OF CONTENTS INTRODUCTION............................................................................ 3 UNPACKING AND CHECKING EQUIPMENT ............................. 3 PLANNING THE INSTALLATION................................................ 6 EQUIPMENT REQUIRED .............................................................. 8 INSTALLATION IN VEHICLES POWERED BY LIQUEFIED (LP) GAS......................................................................................... 9 INSTALLATION........
Résumé du contenu de la page N° 3
INTRODUCTION This manual contains installation instructions for the Orion Mobile Radio Unit and associated accessories. These instructions cover the mounting and cabling of the radio; interconnection and wiring diagrams are provided for reference. Before installation the radio should be programmed using an IBM compatible personal computer and the following items: Serial/Flash Programming Interface Module TQ3370 Programming Cable TQ3377 EDACS Programming Software TQ3374 or Conventional Pro
Résumé du contenu de la page N° 4
• Front Mount Bracket Kit D2MA3N or • Remote Mount Kit D2MA3R with • Control Unit Mount Kit D2MA3J • Operator's Manual LBI-38888 • Installation Manual LBI-38901 Figure 1 - Orion Mobile Radio Components And Mounting Hardware USA EURO Figure 2 - Rear View Of Radios 4
Résumé du contenu de la page N° 5
Figure 3 - Cables 5
Résumé du contenu de la page N° 6
Table 1 - Orion Mobile Radio Optional Accessories Option Description Part Number D2AN1M 900 MHz, 1/4 Wave Whip Antenna 19B801182P3 D2AN1L 800 MHz 1/4 Wave Whip Antenna 19B209568P5 D2AN1R VHF/UHF, 1/4 Wave Whip Antenna 19B209568P6 D2CE1V Power Cable, 7.5 M 19B802622P1 D2CE1W Accessory Cable, Front Mount 19B802554P1 D2CE1X Accessory Cable, Rear Mount 19B802554P6 D2CE1Y Control Cable, Remote Mount, 5.5 M 19B802554P3 D2CE1Z Accessory Cable, Front Mount EURO 19B802554P11 D2CE5R Extended Option Access
Résumé du contenu de la page N° 7
Figure 4 - Typical Installation (Remote Mount Shown) It is suggested that the radio be installed by one of the many authorized General Electric Service Stations located throughout the United States. These experienced service stations can provide a proper radio installation and make any final adjustments that may be needed. WARNING • Vehicular Electronics-Electronic fuel injection systems, electronic anti-skid braking systems, electronic cruise control systems, etc., are typical of the types of e
Résumé du contenu de la page N° 8
EQUIPMENT REQUIRED The equipment required for installing the Orion Mobile Radio is listed below: • Crimping Tool for fuse holder • Electric drill for drilling mounting holes • Drills and circle cutters as follows: No. 31 (1/8-inch) drill No. 27 (9/64-inch) drill 5/8-inch drill or circle cutter 3/4-inch circle cutter, hole saw or socket punch • Phillips and flat-blade screwdrivers • POZIDRIV driver • No. 20 Torx driver Torx is a registered trademark of CAMCAR Division TEXTRON, Inc. POZIDRIV is
Résumé du contenu de la page N° 9
INSTALLATION IN VEHICLES POWERED BY LIQUEFIED (LP) GAS Radio installation in vehicles powered by liquefied petroleum gas with the LP gas container in the trunk or other sealed-off space within the interior of the vehicle must conform to the National Fire Protection Association Standard NFPA 58 which requires that: • Space containing radio equipment shall be isolated by a seal from the space containing the LP gas container and its fittings. • Outside filling connections shall be used for the LP g
Résumé du contenu de la page N° 10
Figure 5 - Front Mount Basic Accessory Interconnections (USA Models Only) Figure 6 - Front Mount Basic Accessory Interconnections (EURO Models Only) Figure 7 - Front Mount Extended Option Accessory Interconnections (USA Models Only) 10
Résumé du contenu de la page N° 11
Figure 8 - Front Mount Extended Option Accessory Interconnections (EURO Models Only) Figure 9 - Remote Mount Basic Accessory Interconnections (USA Models Only) Figure 10 - Remote Mount Basic Accessory Interconnections (EURO Models Only) 11
Résumé du contenu de la page N° 12
Figure 11 - Remote Mount Extended Option Accessory Interconnections (USA Models Only) Figure 12 - Remote Mount Extended Option Accessory Interconnections (EURO Models Only) Power Cable The USA power cable (19B802622P1) consists of a red lead A+ and a black lead A- connected to a molded 2-pin power connector and supplied with ring terminals. The EURO power cable also consists of a red lead A+, a black lead A- and is terminated with ring terminals, but it is connected to P1 of the Accessory Cable
Résumé du contenu de la page N° 13
wire ends into the small openings at the end of each fuse holder section and crimp a fuse connector to each wire. Prepare the other end of the short wire in the same manner as in Step 2 and connect to the positive (+) terminal of the battery. NOTE Do not install fuse into fuse holder until installation is completed and all connections have been checked. Figure 13 - Power Cable 19B802622P1 (USA Only) Accessory Cable Front Mount The Basic Accessory Cable, at one end, consists of the basic accesso
Résumé du contenu de la page N° 14
(19B802554, Sh.1, Rev. 19) Figure 14 - USA Front Mount Standard Accessory Cable 19B802554P1 14
Résumé du contenu de la page N° 15
(19B802554, Sh.9, Rev. 19) Figure 15 - EURO Front Mount Standard Accessory Cable 19B802554P11 15
Résumé du contenu de la page N° 16
(19B802554, Sh.2, Rev. 19) Figure 16 - USA Front Mount Extended Option Accessory Cable 19B802554P2 16
Résumé du contenu de la page N° 17
(19B802554, Sh.10, Rev. 19) Figure 17 - EURO Front Mount Extended Option Accessory Cable 19B802554P12 17
Résumé du contenu de la page N° 18
Remote Mount The Basic Accessory Cable, at one end, consists of the basic accessories connector (P3) and the speaker connector (P2). At the other end is the plug P1. P1 will connect to the Option Connector (OPT) which is mounted on the back of the Radio Interface Adapter (RIA). The Extended Option Accessory Cable is the same as the Basic Cable but with the addition of the Extended Option Plug (P4). See Figures 18 and 19. (19B802554, Sh.5, Rev. 19) Figure 18 - Remote Mount Standard Accessory
Résumé du contenu de la page N° 19
(19B802554, Sh.6, Rev. 19) Figure 19 - Remote Mount Extended Option Accessory Cable 19B802554P7 19
Résumé du contenu de la page N° 20
Ignition Sense (All Applications) NOTE • The radio as shipped from the factory has the "ignition sense" feature disabled. As such the radio will be powered ON or OFF as determined by the front panel ON/OFF/VOLUME control only (assuming A+ and A- are connected). If it is desired to enable the "ignition sense" feature, open top cover of radio and remove shield from logic PWB. Slide switch SW601 from position 3-2 to 1-2. Replace shield and top cover. Be sure to apply correct torque to screws ho
