Résumé du contenu de la page N° 1
Instruction Manual
PN 51-1055pHC/rev.K
February 2006
®
Model Solu Comp II
Dual Input pH/Conductivity Analyzer
Résumé du contenu de la page N° 2
ESSENTIAL INSTRUCTIONS WARNINGS RISK OF ELECTRICAL SHOCK READ THIS PAGE BEFORE PROCEEDING! Your purchase from Rosemount Analytical, Inc. has Equipment protected throughout by double insulation. resulted in one of the finest instruments available for your particular application. These instruments have • Installation of cable connections and servicing of this prod- been designed, and tested to meet many national uct require access to shock hazard voltage levels. and international standards.
Résumé du contenu de la page N° 3
QUICK START GUIDE FOR MODEL SOLU COMP II pH/CONDUCTIVITY ANALYZER (Model Option 1055-22-30) 1. Refer to Section 2.0 for installation instructions. 2. Wire sensor(s) to the analyzer. See the drawings below. Refer to the sensor instruction sheet for details. Make alarm and output connections as shown below. NOTE For sensors without solution ground, please use the RC kit included with the instrument. Wiring Connections for Solu Comp II Model 1055-01-10 Wiring Connections for Solu Comp II Model 1055
Résumé du contenu de la page N° 4
4. When the analyzer is powered up for the first time, Quick Start screens appear. Using Quick Start is easy. a. A blinking field shows the position of the cursor. b. Use the or key to move the cursor left or right. Use the or key to move the cursor up or down or to increase or decrease the value of a digit. Use the or key to move the decimal point. c. Press ENTER to store a setting. Press EXIT to leave without storing changes. Pressing EXIT also returns the display to the previou
Résumé du contenu de la page N° 5
QUICK REFERENCE GUIDE MENU TREE FOR pH/ORP/REDOX/CONDUCTIVITY/RESISTIVITY/TDS MEASUREMENTS pH/cond/temp
Résumé du contenu de la page N° 6
MODEL SOLU COMP II TABLE OF CONTENTS MODEL SOLU COMP II DUAL INPUT pH/CONDUCTIVITY ANALYZER TABLE OF CONTENTS Section Title Page 1.0 DESCRIPTION AND SPECIFICATIONS ................................................................ 1 1.1 Features and Applications........................................................................................ 1 1.2 Specifications........................................................................................................... 2 1.3 Ordering Informat
Résumé du contenu de la page N° 7
MODEL SOLU COMP II TABLE OF CONTENTS TABLE OF CONTENTS CONT’D Section Title Page 6.0 CALIBRATION ........................................................................................................ 45 6.1 Introduction .............................................................................................................. 45 6.2 Calibrating Temperature........................................................................................... 46 6.3 Two-Point Buffer Calibration (Auto Cal
Résumé du contenu de la page N° 8
MODEL SOLU COMP II TABLE OF CONTENTS LIST OF FIGURES Number Title Page 2-1 Panel Mount Installation ........................................................................................... 12 2-2 Pipe Mount Installation ............................................................................................. 13 2-3 Surface Mount Installation........................................................................................ 14 3-1 Removing the Knockouts ...............................
Résumé du contenu de la page N° 9
About This Document This manual contains instructions for installation and operation of the Solu Comp II Model 1055 Dual Input pH/Conductivity Analyzer. The following list provides notes concerning all revisions of this document. Rev. Level Date Notes 0 1/01 This is the initial release of the product manual. The manual has been reformatted to reflect the Emerson documentation style and updated to reflect any changes in the product offering. A 2/02 Revised specs. B 7/02 Added 399 wiring diagram
Résumé du contenu de la page N° 10
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS SECTION 1.0. DESCRIPTION AND SPECIFICATIONS 1.1 FEATURES AND APPLICATIONS 1.2 SPECIFICATIONS 1.3 ORDERING INFORMATION AND ACCESSORIES ENCLOSURE: The panel mount version fits stan- 1.1 FEATURES AND APPLICATIONS dard ½ DIN panel cutouts, and its shallow depth is The Solu Comp II analyzers offer the choice of sin- ideally suited for easy mounting in Hoffman-type gle or dual sensor input with measurement choices enclosures. A panel
Résumé du contenu de la page N° 11
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.2 SPECIFICATIONS - General RFI/EMI: EN-61326 Case: ABS (panel-mount), polycarbonate (pipe- and surface-mount). All versions are NEMA 4X/CSA 4 LVD: EN-61010-1 (IP65). Input: Choice of single or dual sensor input with Dimensions measurement choices of pH/ORP, conductivity/ Panel (code -10): 6.10 x 6.10 x 3.72 in. (155 x resistivity, toroidal conductivity, flow, chlorine, dis- 155 x 94.5 mm) solved oxygen, and dissolved ozone. Fiel
Résumé du contenu de la page N° 12
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS CONTACTING CONDUCTIVITY (Codes -20 and/or -30) Measures conductivity in the range 0 to 20,000 µS/cm. RECOMMENDED SENSORS FOR Display choices are conductivity, resistivity, and TDS CONDUCTIVITY: (total dissolved solids). Three temperature corrections The Solu Comp II is intended for use with the are available: high purity water (dilute sodium chlo- ENDURANCE Model 400 series conductivity sensor ride), cation conductivity (dilute hydroc
Résumé du contenu de la page N° 13
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS TOROIDAL CONDUCTIVITY (Codes -21 and/or -31) When used with Model Series 200 Toroidal RECOMMENDED SENSORS: Conductivity Sensors, display choices are conductiv- Model 222 Flow-through conductivity sensor ity, resistivity, and percent concentration. The per- Model 225 Clean-in-place conductivity sensor cent concentration selection includes the choice of four common solutions (0-12% NaOH, 0-15% HCl, Model 226 Large bore conductivity sens
Résumé du contenu de la page N° 14
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS pH/ORP (Codes -22 and/or -32) For use with any standard pH or ORP sensor and all RECOMMENDED SENSORS FOR pH: Uniloc sensors and junction boxes with built-in diag- Model 320B Flow Through pH nostic style preamplifiers, display choices are pH, Model 320HP High Purity pH ORP or Redox. The automatic buffer recognition fea- Model 328A Steam Sterilizable pH ture uses stored buffer values and their temperature Model 370 and 371 EuroSenz pH c
Résumé du contenu de la page N° 15
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS FLOW (Standard on all models or stand alone, Code -23 and/or -33) For use with most pulse signal flow sensors, the Solu RECOMMENDED SENSORS Comp II's user selectable units of measure include +GF+ Signet 515 Rotor-X Flow sensor Model flow rates in GPM (Gallon per minute), LPM (liters per 515/8510-XX (PN P51530-PO) minute), or m3/hr (cubic meters per hour), and veloci- Fluidyne Flow Sensor Model 2300A ty in ft/sec or m/sec. When config
Résumé du contenu de la page N° 16
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS DISSOLVED OXYGEN (Code -25) When used with an oxygen permeable membrane- PERFORMANCE SPECIFICATIONS covered amperometric sensor, display choices are Measurement Range: 0-20 ppm (mg/L) dissolved ppb or ppm dissolved oxygen or % saturation. oxygen; 0- 250% saturation Because the permeability of the membrane is a func- Resolution: 0.01 ppm; 0.1 ppb for 499A TrDO sensor tion of temperature, a correction is necessary when (when O <1.00 ppm
Résumé du contenu de la page N° 17
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.3 ORDERING INFORMATION The Solu Comp II analyzers offer the choice of single or dual sensor input with measurement choices of pH/ORP, conductivi- ty/resistivity, toroidal conductivity, flow, chlorine, dissolved oxygen, and dissolved ozone. See combination guide (on the fol- lowing page) for valid combinations. Standard features include two isolated outputs, three alarm relays, customizable two-line display, and temperature correctio
Résumé du contenu de la page N° 18
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS COMBINATION GUIDE 5 5 * For D.O. sensors with 22k thermistor, use Suite 1 only. 9
Résumé du contenu de la page N° 19
MODEL SOLU COMP II SECTION 1.0 DESCRIPTION AND SPECIFICATIONS ACCESSORIES (Weights are rounded up to nearest whole lb or 0.5 kg) PART NUMBER DESCRIPTION WEIGHT SHIPPING WT. 23820-00 Pipe mounting kit, includes U-bolts, mounting bracket, nuts, 2 lb (1.0 kg) 4 lb (2.0 kg) washers, and screws (complete) 23554-00 Gland fittings, PG 13.5, 5 per package 1 lb (0.5 kg) 2 lb (1.0 kg) 9240048-00 Tag, stainless steel (specify marking) 1 lb (0.5 kg) 1 lb (0.5 kg) pH INPUT 9210012 Buffer Solution, 4.01 pH, 1
Résumé du contenu de la page N° 20
MODEL SOLU COMP II SECTION 2.0 INSTALLATION SECTION 2.0. INSTALLATION 2.1 UNPACKING AND INSPECTION 2.2 INSTALLATION 2.1 UNPACKING AND INSPECTION Inspect the shipping container. If it is damaged, contact the shipper immediately for instructions. Save the box. If there is no apparent damage, unpack the container. Be sure all items shown on the packing list are present. If items are missing, notify Rosemount Analytical immediately. 2.2 INSTALLATION 2.2.1 General Information 1. Although the analyz
