Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
HB0056
NP64000 SERIES
! INTENDED FOR DOMESTIC COOKING ONLY !
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL TO HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 11 TO 13
NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)
www.nutone.com
V07451 rev A
Résumé du contenu de la page N° 2
! ! WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC TO REDUCE THE RISK OF INJURY TO PERSONS SHOCK OR INJURY TO PERSONS, OBSERVE THE IN THE EVENT OF A RANGE TOP GREASE FIRE, FOLLOWING: OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the 1. SMOTHER FLAMES with a close-fitting lid, cookie manufacturer. If you have questions, contact the sheet or metal tray, then turn off the burner. BE manufacturer at the address or telephone number CAREFUL TO PREVENT BURNS. IF THE FL
Résumé du contenu de la page N° 3
- NP64000 SERIES RANGE HOOD SYSTEM - INTERIOR BLOWERS Model 647 Model 634 or 644 Model 643 (7” Rd wall cap) (roof cap) (8” Rd wall cap) Model 418 10” round Model 415 adjustable elbow 7” round adjustable (optional) elbow (optional) 8” round Model 407 standard (7” round - duct 2 ft. sections) Model 412 Model 459 transition Model 413 1 transition (3 /4” x 14” to 8”) 1 transition (3 /4” x 10” to 7”) 1 (3 /4” x 10” to 8”) Standard duct 1 (3 /4” x 10”) Duct 1 (3 /4” x 14”) 1 Adapter and damper 3 /
Résumé du contenu de la page N° 4
- NP64000 SERIES RANGE HOOD SYSTEM - IN-LINE AND EXTERIOR BLOWERS Model 441 Model 437 Model HLB9 (800 cfm) (10” Rd wall cap) (High capacity roof cap) Model 335 (1200 cfm) or HLB11 (1100 cfm) or 336 (1500 cfm) in-line blower exterior blower Model 331H (600 cfm) (includes two 8” x 12” to or 332H (900 cfm) 10’’ round transitions) exterior blower Model 441 (10” Rd wall cap) Model HLB6 (600 cfm) in-line blower (includes two 4½” x 18½” to 10’’ round transitions) Model 421 Model 418 (10” Rd. vert. 10
Résumé du contenu de la page N° 5
1. SELECT BLOWER OPTION AND INSTALL DUCTWORK Either an interior or exterior blower or in-line blower may be used with this hood. The NuTone premier NP64000 Series must be installed with blower models P5, P8, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately). Plan where and how the ductwork will be installed. If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 3, 6, 9, 10, 12 a
Résumé du contenu de la page N° 6
2. PREPARE THE INSTALLATION Make sure that the following items are included: - Range hood - Accessories: Filters Bag of parts including: 1 (4) lock nuts, (1) wire clamp, (8) /2” double thread screws, (2) wire connectors, 1 3 (2) /2” standard screws, (6) /8 screws. Parts sold separately: 1 - Interior blower Model P5 includes blower, rough-in kit, flow deviator and 3 /4” x 10” adapter 1 1 - Interior blower Model P8 includes blower, rough-in kit, flow deviator and 3 /4” x 10” adapter and
Résumé du contenu de la page N° 7
5. CHOOSE THE OPENING (INTERIOR BLOWER) Remove the knockout for the chosen opening (horizontal at the back of the hood or vertical on rough-in plate). See pictures below. CAUTION When using P5 blower, remove the 10’’ wide knockout (smaller part). If using P8 blower, remove the knockout corresponding to the ducting installed (10’’ or 14’’). 14’’ KNOCKOUT 10’’ KNOCKOUT HD0076 HD0077 Removing horizontal knockout opening on back of hood Removing vertical knockout opening on rough-in plate 6. INSTA
Résumé du contenu de la page N° 8
8. INSTALL THE ADAPTER (INTERIOR BLOWER) 1 Using two (2) standard /2’’ screws, secure the adapter to the top (or back) of the hood. Seal the adapter to the hood using duct tape. HD0005 HD0006 9. INSTALL THE HOOD (ALL BLOWERS) INTERIOR BLOWER: Run power cable to installation location. Place the hood to its location. Mark the position of the 1 screws (smaller part of the key holes) with a pen. Remove the hood and install the (8) /2” double thread screws 1 leaving a /8” gap (4 screws for 30” hood)
Résumé du contenu de la page N° 9
10. CONNECT WIRING (ALL BLOWERS) ! WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally. INTERIOR BLOWER:Connect cable into wiring box using wire connectors. Connect wires as follow: BLACK to BLACK, WHITE to WHITE and GREEN or BARE wire under ground screw. Reinstal
Résumé du contenu de la page N° 10
11. INSTALL THE BLOWER (INTERIOR BLOWER) (CONT’D) Install screws into the location as shown in the pictures below (single blower or dual blower). Do not tighten screws down 1 fully, leave a /8” gap. Hang blower unit onto blower plate (screws through the large part of the keyhole). Slide the blower to its position (screws in the small part of the keyhole). Tighten the screws. HD0044 HD0044 Single blower (P5) Dual blower (P8) Secure the blower by installing 2 more screws into the locations shown i
Résumé du contenu de la page N° 11
12. LIGHT BULBS This range hood uses 50W halogen lamps. (120V, 50W, PAR 20) Install the lamps by rotating them clockwise into their socket holder. 13. HEAT LAMPS The heat lamps required are 120V, 175W max, infrared bulbs. (120V, IR 175W, PAR 38) White halogen lights can be used if warming shelves are not used. (120V, 90W, PAR 38) Install the lamps by rotating them clockwise into their socket holder. 14. INSTALL FILTERS It is recommended to install side filters first and finish with center one(s)
Résumé du contenu de la page N° 12
15. USE AND CARE (CONT’D) Hood cleaning Stainless steel cleaning: How to maintain its « BRIGHT LOOK » Do: - Regularly wash surfaces with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent. - Always clean in the direction of original polish lines. - Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely. - You may also use a specialized household stainless steel cleaner. Don’t: - Do not use any steel or stainless steel wool or any other
Résumé du contenu de la page N° 13
16. OPERATION (CONT’D) ! WARNING Never place highly flammable material under warming lamps. WARMING LAMPS (INFRARED) Each warming lamp is controlled with its own ON/OFF switch. Use infrared light bulbs (120V, IR175W, PAR38) or white halogen bulbs (120V, 90W, PAR38) if food warming shelves are not used. HEAT SENTRY This hood is equipped with a Heat Sentry thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface. 1) If b
Résumé du contenu de la page N° 14
SERVICE PARTS NP64000 Series 1 17 1 19 16 16 18 2 6 12 3 11 5 14 15 4 13 16 16 16 78 1 9101 7 HL0073 KEY QTY (hood width) PART NUMBER DESCRIPTION # 30” 36” 42” 48” 1 V02264 SOCKET LAMP 4 4 5 5 2 V02773 MALE CONNECTOR 1 1 1 1 3 V02772 FEMALE CONNECTOR 1 1 1 1 4 V03435 THERMOSTAT 1 1 1 1 5 V03436 THERMOSTAT BRACKET 1 1 1 1 6 V03501 SPEED CONTROLLER 1 1 1 1 7 V03507 SPST SINGLE SWITCH FOR WARMING LAMP 2 2 2 2 8 V03502 SPST DOUBLE SWITCH FOR HALOGEN LIGHT 1 1 1 1 9 V03503 SP
Résumé du contenu de la page N° 15
SERVICE PARTS SINGLE BLOWER/ROUGH-IN (Model P5) 1 20 21 2 23 22 19 3 4 18 17 5 16 7 15 6 14 8 13 6 12 9 11 10 HL0021 KEY PART NUMBER DESCRIPTION QTY # 1 1 1 V13296 ADAPTER AND DAMPER 3 /4’’ x 10’’ 1 2 V03500 AIR DEFLECTOR 1 3 V12997 SINGLE BLOWER ROUGH-IN PLATE ASSEMBLY 1 1 1 4 V03577 FOAM /2” x /2” x 12” 1 5 V02160 CAPACITOR 15MFD 1 4 6 V01869 MACHINE SCREW #6-32 x /4” 1 7 V01857 WIRE COVER 1 8 V01582 LOCK NUT #6-32 1 9 V14973 SINGLE BLOWER ASSEMBLY 1 10 V01810 IMPELLER
Résumé du contenu de la page N° 16
SERVICE PARTS DUAL BLOWER/ROUGH-IN 2 (Model P8) 22 24 1 23 25 3 4 21 5 20 19 18 6 17 16 7 15 14 8 9 11 13 10 12 KEY PART NUMBER DESCRIPTION QTY # 1 1 1 V14971 ADAPTER AND DAMPER 3 /4” x 14’’ 1 1 2 V13296 ADAPTER AND DAMPER 3 /4” x 10’’ 1 3 V03500 AIR DEFLECTOR 1 4 V14975 DUAL BLOWER ROUGH-IN PLATE ASSEMBLY 1 1 1 5 V03577 FOAM /2” x /2” x 12” 1 6 V01582 LOCK NUT #6-32 2 7 V02160 CAPACITOR 15MFD 2 8 V01857 WIRE COVER 1 9 V01766 MOTOR 165W CW 1 10 V03400 BLOWER IMPELLER, HOOD
