Résumé du contenu de la page N° 1
COOKER HOOD
USER HANDBOOK FOR
INSTALLATION AND OPERATION
MODEL HTV10
Résumé du contenu de la page N° 2
Your new Cooker Hood Using your new Cooker Hood is very simple. Nevertheless, to get the best results it is important that you read this handbook thoroughly before installing and using your appliance for the first time. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity company regulations. For your own safety, this should be undertaken by a qualified electrician eg. your local electricity company or a contractor who
Résumé du contenu de la page N° 3
Contents Page Electrical Requirements 2 Get to know your Cooker Hood 4 Installing your Cooker Hood Installation for Recirculation 5-7 Installation for Extraction Mounting Height Fixing to the Cabinet Fixing to the Wall Operating your Cooker Hood 8 The Controls Do’s and Don’ts Caring for your Cooker Hood 9-10 Filters and their Replacement Cleaning How to Replace the Light Troubleshooting 11 Ke
Résumé du contenu de la page N° 4
Get to know your Cooker Hood. Unpacking Before installation, ensure that you have removed all packing pieces. Controls Visor Light Grease Filter Wire Clips Dimensions 3 Height 15cm (5 /4in) 1 Width 60cm (23 /2in) 1 Depth 55cm (21 /2in) Including visor. 4
Résumé du contenu de la page N° 5
Installing your Cooker Hood Your new Cooker Hood can be installed either NOTE: The hood is more efficient in the for recirculation or extraction through an exhaust mode, therefore this position outside wall. should be selected during the warmer months of the year when no heating is Installation: being used. When the room is being These distances, between hobs and grease heated, if the recirculation position is filter must be observed. selected heat will not be wasted. Minimum 65cm over an electr
Résumé du contenu de la page N° 6
Installing your Cooker Hood Top Extraction (Fig.4) Fig.4 If the exhaust air is being drawn upwards, a pipe with a diameter of 100mm is necessary and the blanking plate must be fitted in the rear outlet. To check that the hood is set up for extraction, open the grille panel and make sure that the conversion lever on the unit is in the exhausting position. Rear Extraction (Fig.5) Fig.5 If the air is to be drawn off to the rear, a pipe with a diameter of 100mm is necessary and the blanking plate sh
Résumé du contenu de la page N° 7
Installing your Cooker Hood Wall Vent Kit: For connecting the hood either directly Fig.7 through a wall or in conjunction with a duct- ing pipe, we recommend the use of a Wall Vent Kit. A 3m extension pipe is also available. Both of these are 100mm diameter and may be obtained from your nearest retailer or the Genuine Parts and Accessories Mail Order Hotline (see back cover) and must be used where there is a cavity wall. MOUNTING Mounting Height: Your Cooker Hood is suitable for wall mounting or
Résumé du contenu de la page N° 8
Operating your Cooker Hood The Controls Make sure that the Cooker hood is wired in Position 3 when frying or cooking foods with and the power supply is switched on. strong odours. Your Cooker hood has three speeds, to give Simply slide the selector to the required you the correct extraction level to suit your setting. It is advisable to leave it running for cooking conditions. approximately 15 minutes after finishing 1Low cooking to ensure all odours are extracted. 2Normal There is a separate se
Résumé du contenu de la page N° 9
Caring for your Cooker Hood Before doing any cleaning or replacing the fil- Fig.11 ters or light bulb, always ensure that the elec- tricity supply to the Cooker Hood is switched ‘OFF’. Filters and their replacement: THE GREASE FILTER - Your Cooker Hood is fitted with a grease filter 4. Replace the retaining clips. which absorbs grease, dust etc. and helps to 5. Close the grille panel. keep the appliance clean inside. Gradually the filter will become saturated and should be THE CARBON FILTER - re
Résumé du contenu de la page N° 10
Caring for your Cooker Hood Cleaning: The exterior of the Cooker Hood should be cleaned regularly to keep it looking like new. Wipe over with a soft cloth, wrung out in warm water and dry with a clean soft cloth. Wear protective gloves. You can use mild non-abrasive cleaners but always read the manufacturer’s instructions first. Always test their suitability on a small area of the Cooker Hood not noticeable in normal use. NOTE: DO NOT use scouring pads or abrasive cleaners as they may scratch th
Résumé du contenu de la page N° 11
Troubleshooting. First, don’t panic! Parts There may be nothing wrong at all. Look for Please remember your new appliance is a your problem below, then check the things we complex piece of equipment. suggest. More often than not, this will give you the answer to your problem, and you’ll be able Repairs may only be performed by qualified to carry on without having to telephone your technicians. ‘DIY’ repairs or unqualified and Service Office. untrained service people may put you
Résumé du contenu de la page N° 12
Key Contacts Service Hotpoint has the largest appliance manufacturer’s service team in Europe, trained specialists directly employed by us to ensure your complete confidence. Repair Service UK: 08709 066 066 Republic of Ireland: 1850 302 200 You will be asked for the following information:- Name, address and postcode. Telephone number Model / Serial number of the appliance Clear and concise details of the query or fault Place and Date of purchase (Please keep the receipt as evidence will be requ
