Résumé du contenu de la page N° 1
PLPK5TVD
OWNER’S MANUAL
COLOUR LCD TV/RECEIVER
Résumé du contenu de la page N° 2
INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of
Résumé du contenu de la page N° 3
MOUNTING THE TUNER UNIT 4 2 6 6 5 4 7 1 6 3 1 8 5 7 5 7 3 8 2 Step 1 Step 2 1. Bracket (A) 5. Tapping Screw with Washer (M5 x 12) 2. Mounting Bolt (M5 x 5) 6. Spring Washer (M6) 3. Bracket (B) 7. Spring Washer (M5) 4. Hexagonal Bolt with Washer (M6 x 12) 8. Double Sided Tape INSTALL THE DISPLAY UNIT Before install the display unit, please remove its tail screw and cable parts. This unit can be properly installed either from “front” (convertional DIN Front-mount) or “rear” (DIN Rear-mount instal
Résumé du contenu de la page N° 4
1. Dashboard 1 2. Nut (M5) 6 3. Spring Washer 4 4. Tapping Screw with Washer (M5 x 25) 2 7 5. Screw 5 3 6. Plain Washer 7. Strap Be sure to use the strap to secure the (Fig. 2) back of the unit in place. The strap can be bent by hand to the desired angle. Removing the unit 1 1. Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers upward and out to makes it possible to remove the unit. DIN REAR-MOUN
Résumé du contenu de la page N° 5
HOW TO OPEN AND CLOSE THE SCREEN DISPLAY 1. Press release button to draw out the screen display. Release Button 2. Turning the display upward. 3. Adjusting the viewing angle. Angle should be adjusted slowly without applying unreasonable force. 5
Résumé du contenu de la page N° 6
4. Turning the display downward. Make sure to return the display to centre position before drawing in. It cannot be draw in with its angles adjusted. 5. Push the panel, the display will be drawn in. 6
Résumé du contenu de la page N° 7
ELECTRICAL CONNECTION RADIO/TV MAIN UNIT RADIO/TV MAIN UNIT (VIEW FROM REAR) (VIEW FROM FRONT) TV DIVERSITY ANTENNA INPUT AV INPUT TV MONITOR AV1 RADIO CONTROL AV2 VIDEO AUDIO–R AUDIO–L DISPLAY UNIT TO POWER SUPPLY RADIO CONTROL TV MONITOR 7 BLUE/WHITE POWANT RED ACC YELLOW MEMORY CHOKE BOX BLACK GROUND VIOLET REAR Rch SPK GREY VIOLET/BLACK TV CONTROL GREY/BLACK GREEN REAR Lch SPK GREEN/BLACK GREY FRONT TV DIVERSITY ANTENNA INPUT Rch SPK GREY/BLACK RADIO ANTENNA
Résumé du contenu de la page N° 8
OPERATION 16 11 7 24 4 2 13 1 5 6 8 12 15 3 14 19 10 20 9 18 21 22 17 1 23 4 8
Résumé du contenu de la page N° 9
GENERAL OPERATION • ON/OFF Switch on the unit by pressing PWR button (1). When system is on, press it again to turn it off. • FACEPLATE RELEASE Press REL button (2) to draw out the faceplate, push the panel to draw in. When the faceplate is drawn out, turn the faceplate upward and adjust TV display. • SELECTING SOUND MODE Press SEL button (6) to move display through volume, bass, treble, balance and fader functions. Use (7) and (8) buttons to adjust the selected mode. When mode has not
Résumé du contenu de la page N° 10
Time Setting - Set hours: Holding down T/F button (5) for several seconds, and the clock is blinking on the display, press button (14) to adjust the hour. - Set minutes: Holding down T/F button (5) for several seconds, and the clock is blinking on the display, press button (13) to adjust the minutes. • LIQUID CRYSTAL DISPLAY The LCD (4) can show the current state of the unit. • RESET Reset button (24) must be activated with either a ball-point pen or thin metal object. The reset button
Résumé du contenu de la page N° 11
RADIO OPERATION • SELECTING BAND Press BAND button (11) to change between three FM bands and two AM bands. Each band stores up to six preset stations. FM1 FM2 FM3 AM1 AM2 • SELECTING STATION During radio mode, press MAN/SKP button (13) to increase frequency or (14) to decrease frequency by one step of channel spacing. Hold the button longer for fast tuning. The frequency is updated correspondingly on display. • SELECTING MEMORY Press preset memory buttons (15) to preset stations at
Résumé du contenu de la page N° 12
TV OPERATION • SELECTING RECEIVING MODE Press TV/AV button (17) to select among TVch/AV1/AV2. • SELECTING CHANNEL Press CH+ button (9) or CH– button (10) to choose channel upward or downward • MENU CONTROL In TV mode Press MENU button (18) to switch the MENU CONTROL mode. And the main menu includes three sub-menus: PICTURE MENU, TUNER MENU and SYSTEM MENU. Press MENU button (18) for the first time: PICTURE TUNE SYSTEM MENU PIC ADJUST Press the MENU button repeatedly or press CH+ button (9) or CH
Résumé du contenu de la page N° 13
Note: When you set the color mode to “PAL” in SYSTEM MENU, there is no “TINT” item to display. In this menu, the range of setting value is 00~63, and the recommended range of these values are listed below: BRIGHT: 10~32 CONTRAST: 20~40 COLOR: 40~50 SHARP: 63 TINT: 10 TUNER MENU --POSITION -- TUNER MENU POS 1 SKIP ON BAND UHF FINE AFT OFF SEARCH ASM POSITION setup You can use numeric buttons to input the TV channel number. For example, you input 8, when you turn off the unit and then turn it on a
Résumé du contenu de la page N° 14
--BAND-- TUNER MENU POS 1 SKIP ON BAND UHF FINE AFT OFF SEARCH ASM BAND setup You can use CONTROL+ button (19) or CONTROL– button (20) to switch between UHF, VHFL and VHFH band. --FINE-- TUNER MENU POS 1 SKIP ON BAND UHF FINE AFT OFF SEARCH ASM FINE setup When the frequency has warp, and the picture displayed unstable, you can use CONTROL+ button (19) or CONTROL– button (20) to start FINE function to adjust it. --AFT-- TUNER MENU POS 1 SKIP ON BAND UHF FINE AFT OFF SEARCH ASM AFT (Auto Frequency
Résumé du contenu de la page N° 15
--SEARCH-- TUNER MENU POS 1 SKIP ON BAND UHF FINE AFT OFF SEARCH ASM SEARCH setup Use CONTROL+ button (19) or CONTROL– button (20) to start manual station search. And it will start from the band you select in BAND setup. The SKIP and AFT two items will be set automatically. --ASM-- TUNER MENU POS 1 SKIP ON BAND UHF FINE AFT OFF SEARCH ASM ASM (Auto Search Memory) setup Use CONTROL+ button (19) or CONTROL– button (20) to start auto station search. The SKIP, BAND and AFT three items will be set au
Résumé du contenu de la page N° 16
COLOR setup Use CONTROL+ button (19) or CONTROL– button (20) to switch color mode among AUTO, PAL, N3.58 and N4.43. --SOUND-- SYSTEM MENU COLOR AUTO SOUND M LANG. ENGLISH B/B ON CORING ON HALFTONE ON SOUND setup Use CONTROL+ button (19) or CONTROL– button (20) to switch sound mode among M, B/G, I and D/K. --LANG.-- SYSTEM MENU COLOR AUTO SOUND M LANG. ENGLISH B/B ON CORING ON HALFTONE ON LANG. (Language) setup Use CONTROL+ button (19) or CONTROL– button (20) to switch between ENGLISH and CHINESE
Résumé du contenu de la page N° 17
--CORING-- SYSTEM MENU COLOR AUTO SOUND M LANG. ENGLISH B/B ON CORING ON HALFTONE ON CORING setup Use CONTROL+ button (19) or CONTROL– button (20) to switch between ON and OFF. When the coring function is on, it can effectively decease the picture noise and improve the image quality. --HALFTONE-- SYSTEM MENU COLOR AUTO SOUND M LANG. ENGLISH B/B ON CORING ON HALFTONE ON HALFTONE setup Use CONTROL+ button (19) or CONTROL– button (20) to switch the menu background between ON and OFF. Note: In the m
Résumé du contenu de la page N° 18
• PROGRAM SCANNING Press SCAN button (22), “SCAN OFF” will display on the lower left corner of the screen. Press it again, the screen will display “SCAN ON”, then it begins to scan 1.5 seconds of each channel in sequence. When it completes, the screen will display “SCAN OFF”. In the course of scanning, press SCAN button (22), “SCAN OFF” will also display on the screen and it stops on the TV channel just scanning. • SCREEN DISPLAY Press DSP button (21), the screen will display the current status
Résumé du contenu de la page N° 19
REMOTE CONTROL HANDSET 1 2 3 4 16 5 17 6 7 8 9 10 13 11 14 12 15 CONTROL & FUNCTION KEYS 1. POWER = Press POWER to turn the unit ON or OFF 2. TV/AV = Switch between TV/AV1/AV2 3. 0 - 9 = Numeric buttons, press to select the corresponding channel 4. -/-- = Digital selecting button, cooperatively used with numeric buttons 5. MUTE = Press to mute the sound. When release the button, the screen will display VOLUME XX for about 4 seconds, and this is the AUDIO level setting value of the TV unit. Th
Résumé du contenu de la page N° 20
SPECIFICATION GENERAL Power Supply Voltage : DC 12 Volts, Negative Ground Maximum Power : 4 x 60 Watts Load Impedance : 10 Ampere (max.) Tone Controls - Bass (at 100 Hz) : + / – 10 dB - Treble (at 10 KHz) : + / – 10 dB TV Monitor Screen Size : 5.0” TFT Resolution : 960 x 234 dots TV Sensitivity : 45 dBµ V/PD (max.) @CH25 in average RADIO FM Frequency Coverage : 87.5 to 107.9 MHz Sensitivity (30 dB S/N) : 6 µ V Image Rejection : > 45 dB Stereo Separation : > 25 dB AM Frequency Coverage : 530 to 1
