Résumé du contenu de la page N° 1
PT1700MX / PT1701MX /
PT1705MU
Touch Screen LCD Monitors
USER’S GUIDE
www.planar.com
Résumé du contenu de la page N° 2
Important Recycle Instructions: Lamp(s) inside this product contains mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.
Résumé du contenu de la page N° 3
1 Table of Contents Usage Notice Precautions........................................................................................2 Introduction About Planar’s PT1700MX/PT1701MX/PT1705MU.. .........................3 Touch Screen for PT1700MX/PT1701MX/PT1705MU.….…….………4 Package Overview .............................................................................6 Installation Product Overview...............................................................................
Résumé du contenu de la page N° 4
2 Usage Notice Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning- Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glas
Résumé du contenu de la page N° 5
3 Introduction About Planar’s PT1700MX / PT1701MX / PT1705MU The PT1700MX / PT1701MX / PT1705MU is a 17” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: Direct Analog signal input Active matrix TFT LCD technology 1280x1024 SXGA resolution 17” viewable display area 31.5 ~ 80 kHz horizontal scan 56.3 ~ 75 Hz high refresh rate 0.264mm x 0.264mm Pixel pitch Auto adjustment function Multilingu
Résumé du contenu de la page N° 6
4 Touch Screen for PT1700MX 5-wire resistive touch screen for finger and stylus input Surface: Anti-glare treatment Interface: Dual RS-232 Serial/USB controller Durability: 35 million touches at a single point Hardness of surface: 3H Typical Operating force: 40g~200g when using a silicon rubber tipped pen with a 1 mm diameter minimum and a hardness of 60 degree. Transmittance: 80±2% ® Driver: Windows VISTA, XP, 2000, ME, 98, CE, XP Embedded, Linux, ® Apple Mac OS
Résumé du contenu de la page N° 7
5 Touch Screen for PT1705MU Surface Acoustic Wave (SAW) touch screen for finger and stylus input Surface: Anti-glare treatment Interface: USB controller Durability: 30 million touches at a single point Hardness of surface: Mohs’ Hardness rating of 7 Operating force: 80g (min.) when using a soft-tipped stylus with an 8mm diameter minimum. Transmittance: 88% (Min.) Driver: Windows® VISTA, XP, 2000, 98
Résumé du contenu de la page N° 8
6 Package Overview LCD Display Power Cord VGA Signal Cable USB Cable - Type A to B Audio-in Cable RS-232 Cable (PT1700MX/PT1701MX) Landing Strip Touch Screen Driver User’s Guide Installation CD-ROM DC Power Supply (sold separately)
Résumé du contenu de la page N° 9
7 Installation Product Overview Front View PT1700MX/PT1701MX Bottom View (Without Stand)
Résumé du contenu de la page N° 10
8 PT1705MU Bottom View (Without Stand) Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.
Résumé du contenu de la page N° 11
9 VESA Mount your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
Résumé du contenu de la page N° 12
10 Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can hookup the cables to associated connector. Figure A. 1. To remove the back cover, follow the arrows in Figure A and pull out with your fingers and the cover should be removed from the stand. 2. Follow the instructions on P. 12 ( Figure 11.1 ) to connect the cables to the appropriate connectors. 3. Attach the cover bac
Résumé du contenu de la page N° 13
11 Connecting the Display (Figure 11.1) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (11.1). 3. Connect the D-SUB cable from the display’s VGA input connector to the D-SUB connector of your host computer and tighten the screws (11.1). 4. Connect the Audio-In cable from the audio input port of your displ
Résumé du contenu de la page N° 14
12 Figure 11.1
Résumé du contenu de la page N° 15
13 User Controls Front Panel Controls Control Function No / Icon Menu button Display the OSD menus MENU Select – To select the adjustment items from OSD menus. SELECT/AUTO Select/Auto Auto – To activate the “Auto Adjustment” function to obtain an optimum image. 1. Decreases the brightness of the display Brightness image. Minus/Minus 2. Decreases value of the adjustment items. 1. Increases the brightness of the display
Résumé du contenu de la page N° 16
14 How to Use the OSD Menus 1. Press the "MENU" button to pop up the “on-screen menu” and to select among the four Main Menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “”or ““ button. 1. The OSD menu will automatically close, if you have left it idle for a pre-set time. 2. To disable the OSD menu buttons, please follow the instructions below: (Please note: the monitor has to be ON with
Résumé du contenu de la page N° 17
15 On-Screen Display Menus Main OSD Menu: MAIN MENU SUB MENU Function Description Auto-Adjustment Choose this function to obtain an optimum No/Yes image. Contrast Adjust the contrast of the display image. 0-100 Brightness Adjusts the brightness of the image. 0-100 Horizontal Position Changes the horizontal position of the image. 0-100 Vertical Position Changes the vertical position of the image. 0-100 Clock Changes the display data frequency to match the frequency of yo
Résumé du contenu de la page N° 18
16 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. Check that all the I/O and power connectors are correctly and well connected as described in the “Installation” section. Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image. Check to see if th
Résumé du contenu de la page N° 19
17 Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact Planar for more information. No Signal This message means that the LCD Display has been powered on but it cannot receive any signal from the computer graphics card. Check all the power switches, power cables, and VGA signal cable.
Résumé du contenu de la page N° 20
18 Product Dimensions
