Résumé du contenu de la page N° 1
VMA6491
6.4” ACTIVE MATRIX TFT
COLOR LCD MONITOR
OWNER’S MANUAL
INSTALLATION GUIDE
Résumé du contenu de la page N° 2
INTRODUCTION OWNERÕS MANUAL WARNING! THE CLARION VMA6491 LCD MONITOR IS DESIGNED FOR REAR SEAT PASSENGER VIEWING ONLY. THIS PRODUCT IS NOT INTENDED FOR VIEWING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION SINCE SUCH USE MAY DISTRACT THE DRIVER OR INTER- FERE WITH THE DRIVER’S SAFE OPERATION OF THE VEHICLE AND MAY RESULT IN SERIOUS INJURY OR DEATH. SUCH USE MAY ALSO VIOLATE STATE LAW. CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT
Résumé du contenu de la page N° 3
VMA6491 6.4Ó TFT LCD Monitor PRECAUTIONS: • This monitor is intended for use in DC 12V, negative ground vehicles. • Do not operate the monitor in ways other than described in this guide. Doing so may cause damage and void the warranty. • Be careful not to run down the car’s battery while using a multimedia system with the engine stopped. Doing so may damage the vehicle’s battery or the multimedia system. • Do not disassemble or modify the monitor. Doing so may damage it and void the warranty
Résumé du contenu de la page N° 4
PICTURE ADJUSTMENT OWNERÕS MANUAL DESCRIPTION OF PICTURE ADJUSTMENT: BRIGHTNESS: To adjust the picture brightness, use the Brightness UP and DOWN buttons 3 located on the front panel of the VMA6491. Press and hold the UP button to increase the picture brightness. Press and hold the DOWN button to decrease the picture brightness (see page 2 for button locations). VIEWING ANGLE: To adjust the viewing angle gently tilt the cabinet to the desired position. The rec- ommended viewing angle of the
Résumé du contenu de la page N° 5
VMA6491 6.4Ó TFT LCD Monitor monitor will accept a video signal from any video source with composite video output. The Infrared (IR) sensor will work directly with a Clarion TTX001 or VDH9600 using the IR extension cable provided (see Application starting on page 5 for details). 1. Look over the vehicle for a monitor location. Each vehicle is different and locations will vary. Make sure the monitor will not interfere with the driver’s safe operation of the vehicle. 2. Once a location has be
Résumé du contenu de la page N° 6
APPLICATIONS OWNERÕS MANUAL APPLICATIONS: (With the VDH9600, TTX001 and the FM100S) 1. Pick a location to mount the TTX001 TV tuner. Typically the tuner is located close to the VCR player. Avoid areas with excessive heat or moisture. 2. Mount the TV antenna (ZCB-303 or equivalent) and plug it into the TTX001 antenna input connector. 3. Plug the 16-pin A/V Output and 2-pin Power Molex connector into the TTX001 tuner. Using the supplied A/V cable, connect the Left (white), Right (red), and Vi
Résumé du contenu de la page N° 7
VMA6491 6.4Ó TFT LCD Monitor er. Connect the other jack end of the Y-connector into the IR extension cable coming from the VMA6491 monitor. 5. Plug the video RCA from the VMA6491 into the LINE OUT video connec- tion on the rear of the player. Plug the provided audio RCA cable into the L/R LINE OUT audio connections. Connect the power wires from the VMA6491, TTX001, and the power wires of the VDH9600 together. 6. Remove the vehicle’s radio. Run both the audio RCAs and power wires to the ra
Résumé du contenu de la page N° 8
APPLICATIONS OWNERÕS MANUAL mounting location. Plug each cable into the monitor. Mount the monitor using four (4) M4x8 mm machine screws (machine screws are provided with the mounting brackets). 4. Run the IR extension, video RCA, and power wires to the TTX001 location and plug each into the TTX001 tuner (see the figure below for more details). 5. Pick a location to mount the WH100/200 transmitter, plug in the L/R audio RCAs and power connector. Run the L/R RCAs and power wire to the TTX001’s
Résumé du contenu de la page N° 9
VMA6491 6.4Ó TFT LCD Monitor DESCRIPTION OF RC300 REMOTE BUTTONS: Number Pad 1 Skip 2 Erase/Write 3 Volume Up 4 Volume Down 5 TV/Video 6 Power 7 Channel Up 8 Mute 9 Channel Down 0 Picture Select q Auto Memory w TV/CATV e BATTERY INSTALLATION: • Insert 2 AAA batteries into the compartment located on the back of the unit, observing the proper polarity. NOTE: Each time the batteries are changed, the remote channels must be repro- gramed. Use alkaline batteries; do not use rechargeable batteries.
Résumé du contenu de la page N° 10
TROUBLESHOOTING PUT TITLE HERE OWNERÕS MANUAL TROUBLESHOOTING: Symptom Cause Solution System does not Fuse is blown. Replace external fuse with the same work. value. Power wires are not Check the wire connections and con- connected. nect it properly. The signal condi- The picture has This may due to signals reflected off tion is poor. shadows when con- buildings, mountains, etc. Check nected to the again in a different place and direc- TTX001. tion. The picture has There may be inter- This may
Résumé du contenu de la page N° 11
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 16 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee tha
