Résumé du contenu de la page N° 1
,
INSTALLATION INSTRUCTIONS / OWNER S MANUAL
CD7200
AM/FM HIGH POWER DETACHABLE FACE
CD PLAYER
Résumé du contenu de la page N° 2
INTRODUCTION Congratulations on your purchase of a Profile state-of-the-art single disc CD player. Your selection of a Profile car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your Profile CD player in a new system, you are certain to notice immediate performance benefits. FEATURES 35W x 4 Power Output Power Level Meter Dual RCA Line Output(Front & Rear) ISO/DIN Mounting Clock Blinking Security L
Résumé du contenu de la page N° 3
SAFETY PRECAUTIONS Secure the CD player . When installing your CD player in the vehicle, make sure it is mounted properly in the dash, using an after market installation kit if needed. When using the supplied mounting sleeve, it is a must that you also use the supplied back brace to support the back of the CD player. Use caution when mounting the CD player. Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment wire
Résumé du contenu de la page N° 4
CARE AND MAINTENANCE Cleaning the CD player . When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only the exterior surface of the unit with a dry, clean soft towel using no chemical solvents. Operating in extreme temperatures Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case, wait until the temperature in the vehicle is normal, then resume operation. Protect your CDs. When not using the disc player, it is reco
Résumé du contenu de la page N° 5
DISC CARE AND PLAY: Before playing, clean the disc with a clean, lint-free cloth. Wipe the disc in the direction of the arrow. Do not use solvents such as benzine or thinners. Commercially available cleaners or anti static spray will damage the unit. Insert a disc with the labeled surface up. Label surface up Do not try to insert another disc when one has already been inserted. Doing so may damage the unit. Handle the disc by its edge to keep the disc clean and do not touch the
Résumé du contenu de la page N° 6
ELECTRICAL AND SIGNAL CONNECTIONS , Before making the following connections, take time to look over the vehicle s wiring and determine the location and wires you will be connecting to. If you do not wish to cut or tap into the vehicles existing factory wiring, there are wiring kits available at your car audio retailer that will allow you to plug directly into the factory wiring harness. Make sure to test all wires before connecting to the CD Player. ! Connect Black wire to chassis ground.
Résumé du contenu de la page N° 7
TWO SPEAKER SYSTEM ANTENNA CONNECTOR Low level signal output for connection to amplifier or MEMORY +12V YELLOW 10A Fuse signal processors. + - BLACK(GND) FRONT RCA OUTPUT BATTERY FILTER R +12V R CH RED BOX BLACK L L CH WHITE RED (B+) REAR RCA OUTPUT R 0.5A Fuse R CH RED SWITCHED +12V GRAY L 0.5 A (ON WITH IGNITION) L CH WHITE BLUE AUTO ANTENNA FUSE + + + + GRAY WHITE FRONT LEFT FRONT RIGHT SPEAKER SPEAKER WHITE/BLACK GRAY/BLACK NOT USED NOT USED NOT USED NOT USED CAUTION!
Résumé du contenu de la page N° 8
MOUNTING THE CD PLAYER There are two different ways to mount the CD Player. In most Japanese vehicles you can use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your vehicle does not have ISO/DIN opening, you can mount the CD Player using the supplied DIN sleeve and rear support bracket. When considering your mounting location, make sure the unit will be leveled. If you cannot mount the CD Player level, due to your vehicles design, make sure there is no more
Résumé du contenu de la page N° 9
Attach the back brace to the CD player using the supplied hardware. Then attach the other end of the brace to a firm mounting surface (i.e. Dash brace, fire wall, e.t.c.) This will brace the back of the CD player to ensure solid mounting to prevent theft and provide optimal CD play. Once the CD player is secured, fit the trim ring over outside edge of the radio until it snaps into place. Insert the face plate with the right side first. Angle in the right side slightly then gently pus
Résumé du contenu de la page N° 10
ISO/DIN MOUNTING If you own a Japanese vehicle, you can use the standard ISO/DIN mounting screw holes on the side of the CD player to attach to the existing factory mounting bracket, without using the provided DIN sleeve. ! Remove the factory ISO/DIN mounting bracket from the car along with the factory radio. ! Remove the factory radio from the bracket by unscrewing the two Phillips screws on each side of the radio paying close attention to their screw positions and saving the screws t
Résumé du contenu de la page N° 11
LOCATION AND FUNCTION OF CONTROLS 10 CD7200
Résumé du contenu de la page N° 12
1 POWER To tur n O N the unit, press any button except the EJT and OPEN button. To tur n O F F the unit, press the PWR button. 2 DETACH PANEL Press the OPEN button to detach the front panel. This will allow you to remove the front panel. 3 CD PLAY To play a CD, gently insert the CD into the slot with the label side facing up. The disc will automatically be loaded into the unit and start playing the first track of the disc. The digital display will indicat
Résumé du contenu de la page N° 13
9 10 RADIO TUNE & CD TRACK UP/DOWN, CD FAST FORWARD/REWIND Under radio mode, press the UP 9 or DN 10 button momentarily and repeatedly to change the frequency number up or down one step. Press and hold the button for more than 1 second to seek to the next clear station. In CD play mode, press the UP 9 or DN 10 button to move to the next or previous track. In CD play mode, press and hold the UP 9 or DN 10 button to fast forward or fast re
Résumé du contenu de la page N° 14
Press the SEL button for more than 1 second to display additional set of functions for adjustments, such as DSP, Beep On/Off, and Volume Last/Adjust. DSP - The unit is equipped with 4 preset equalization modes. Press the SEL button for more than 1 second to display DSP OFF. Then use V.UP 5 and V.DN 6 , buttons to choose one of 4 following preset EQ s in the following order. In DSP OFF mode, the EQ is cont
Résumé du contenu de la page N° 15
16 RANDOM PLAY In CD play mode, press the RDM 16 button to play all tracks of the disc in random sequence. Press it again to cancel random play. 17 RADIO SCAN In radio mode, press the SCN 17 button to scan up one strong radio station signal at a time. If a valid radio station is detected, the station number will blink on the LCD for 3 seconds before moving onto the next strong station. Pressing the button again will stop the scan process and remain o
Résumé du contenu de la page N° 16
TROUBLE SHOOTING THE SYSTEM The following chart will help in solving most problems that may occur. Should any problem persist after you have made these checks, please consult your nearest Profile retailer. Before going through this check list, refer back to the wiring and operating procedures. ERROR CODES E 1~ E 10 The unit cannot be operated because of trouble. Press the "RESET" button . If the indicator still appears after pressing the "RESET" 22 22 button , your unit needs r
Résumé du contenu de la page N° 17
SYMPTOM CAUSE SOLUTION The compact The installation angle is Adjust the angle of the unit to less than 30 disc skips. greater than 30 degrees degrees The disc player is installed Check to see if the unit is fastened securely incorrectly with the back brace supporting the rear of the unit. The compact disc is Clean the compact disc with a compact disc extremely dirty or defective cleaning solution or replace the defective disc. compact disc. Condensation build-up on the Leave the disc player
Résumé du contenu de la page N° 18
SPECIFICATIONS GENERAL Power Supply Requirements...........................................DC 12 Volts, Negative Ground || || || || || || Chassis Dimensions ....................................................................7(W) x 6 1/2 (D) x 2 (H) Tone Controls........................................................................................................................... Bass @ 100Hz............................................................................
Résumé du contenu de la page N° 19
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sales receipt, freight prepaid to Profile. This warranty is valid only in the United States.
Résumé du contenu de la page N° 20
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5) Include the return street address and daytime telephone number. 6) Allow 2~3 weeks for rep
