Instruction d'utilisation Metra Electronics 99-7334

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS FOR PART 99-7334
APPLICATIONS
KIA Borrego 2009
99-7334
KIT FEATURES
• DIN Radio Provision
• ISO DIN Radio Provision
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Double DIN Trim Plate
• E) Double DIN Brackets • F) Pocket
B C
Wiring & Antenna Connections (sold separately)
A
• 70-7303 - Hyundai / Kia Harness 2009
• 40-KI10 - Kia Antenna Adapter 2007-up
D
E F
TOOLS REQUIRED:
Sma

Résumé du contenu de la page N° 2

99-7334 TABLE OF CONTENTS Dash Disassembly - KIA Borrego 2009 . . . . . . . . . . . . . . . . . .... . . . . . . . . . . . . . . 1 Kit Assembly - DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN/Stacked ISO Mount Units Provision. . . . . . . . . . . . . . . . . . 4 Final Assembly ......................................... . . 5 *Note: Refer

Résumé du contenu de la page N° 3

99-7334 DASH DISASSEMBLY KIA BORREGO 2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the side trim panels. (Figure A) 3 Remove (4) Phillips screws securing the radio and (2) Phillips screws securing the A/C vent panel above the radio. (Figure B) 4 Unclip and remove the radio and A/C B vent panel as one piece then unplug the radio and vent panel and separate. (Figure C) Continue to kit assembly. C 1

Résumé du contenu de la page N° 4

99-7334 KIT ASSEMBLY DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the bottom opening of the radio housing. (Figure C) Continue to final assembly. B C 2

Résumé du contenu de la page N° 5

99-7334 KIT ASSEMBLY ISO MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio/bracket assembly into the radio housing until it snaps into place. (Figure B) 3 Snap the ISO Trim plate onto the front of the Radio Housing. (Figure C) B 4 Snap the pocket into the bottom opening of the radio housing. (Figure D) Continue to final assembly. D C 3

Résumé du contenu de la page N° 6

99-7334 KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the Double DIN or stacked ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). B (Figure C) 4 Snap the Double D

Résumé du contenu de la page N° 7

99-7334 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Résumé du contenu de la page N° 8

99-7334 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 09/01/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7334