Instruction d'utilisation Metra Electronics 99-2006G

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS FOR PART 99-2006
APPLICATIONS
Cadillac CTS 2003-2007
Cadillac SRX 2004-2006
99-2006/
99-2006G
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked DIN Head Units Provision
• Painted To Match Factory Dash
99-2006 = BLACK
99-2006G = GRAY
KIT COMPONENTS
A) Radio Housing • B) DDIN Brackets • C) DDIN Trim Plate • D) ISO Brackets • E) Trim Plate • F) (8) Phillips screws
• (G) Pocket
E
D
C
B

Résumé du contenu de la page N° 2

99-2006 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 3, 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com

Résumé du contenu de la page N° 3

DASH DISASSEMBLY 99-2006 CADILLAC CTS 2003-2007 CADILLAC SRX 2004-2006 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 11:39 PM 2 Unclip and remove the center air vent assembly above the radio. (Figure A) 60 60 3 Open ashtray and remove (1) Phillips head screw from inside ashtray. B 4 Unclip and remove the a/c control/ ashtray assembly below the radio. 11:39 PM (Figure B) Rear View Remove (4) 10 MM screws securing 5 the radio to the dash. (Figure C, D) 60 60

Résumé du contenu de la page N° 4

99-2006 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket head unit into the cage and secure. (Figure B) Slide the supplied pocket into the 3 B unused opening. ISO MOUNT RADIO PROVISION WITH POCKET A 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the side clips engage. (Figu

Résumé du contenu de la page N° 5

99-2006 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION A 1 Remove the center bar from the 99- 2006 radio housing. (Figure A) 2 Attach the corresponding bracket to the DDIN head unit. (Figure B) Insert the DDIN trim plate into the 3 radio housing. (Figure C) B Position the bracket/radio assembly 4 to the back of the radio housing and secure with the (8) Phillips screws provided. (Figure D) C D Rear View 3

Résumé du contenu de la page N° 6

99-2006 KIT ASSEMBLY STACKED DIN HEAD UNITS PROVISION A Slide the DIN cages into the Radio 1 Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket head units into the cages and secure. (Figure B) B 4

Résumé du contenu de la page N° 7

99-2006 KIT ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring co

Résumé du contenu de la page N° 8

INST992006 1-800-221-0932 www.metraonline.com Rev. 08-08-08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST99-2006