Résumé du contenu de la page N° 1
I n s t a l l a t I o n I n s t r u c t I o n s
M I l l e n n I a ™ I s l a n d (c e Il Ing M o u n t )
r a n g e H o o d s
For use with models:
DHI361
DHI421
DHI482
DHI542
DHI602
Part No. 101744 Rev. B
Résumé du contenu de la page N° 2
T leba fo Con Tne Ts Installation Instructions ............................................... 7-12 Important Safety Instructions .......................................... 1 Electric Service Installation .............................................. . 7 Product Specifications ..................................................... 3 Mounting Bracket Installatio n ... ......................................... 7 General Specifications ............................................
Résumé du contenu de la page N° 3
i mpor Tan T s eaf TY i ns Tur CTsion Important Information About Safety Safety Symbols and Labels Instructions DANGER The Important Safety Instructions and warnings in these Immediate hazards which WILL result in severe instructions are not meant to cover all possible problems personal injury or death. and conditions that can occur . Use common sense and caution when installing, maintaining or operating this or any WARNING other appliance. Hazards or
Résumé du contenu de la page N° 4
i mpor Tan T s fae TY i ns Tru CTosni To reduce the risk of fire, electric shock, serious injury or death when using your range hood, follow basic safety precautions, including the following: WARNING 1. Do not install or operate this hood if it has been damaged, dropp ed, has damaged electrical conduit or wires or is not working properly . If the product is damaged when received, immediately contact the dealer or builder . 2. Use this range hood only
Résumé du contenu de la page N° 5
i mpor Tan T s afe TY i ns Tru CTions WARNING 22. T O REDUCE THE RISK OF INJUR Y T O PERSONS IN THE EVENT OF A RANGE T OP GREASE FIRE: a. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray , then turn of f the burner . BE CAREFUL T O PREVENT BURNS. If the flames do not go out immediately , EV ACUA TE AND CALL THE FIRE DEP AR TMENT . b. NEVER PICK UP A FLAMING P AN - you may be burned. c. DO NOT USE W
Résumé du contenu de la page N° 6
p reparing ofr i ns Talla Tnio Vrifye eth p acka Ge c eonttn S Unpack the parts box and verify that all required A components have been provided. If any item is missing or damaged, please contact the dealer immediately . Do not install a damag ed or incompl ete appliance. Hood assembly with filter(s) A Chimney assembly (2 piece) B Mounting bracket C Blower exhaust cowling (2 blower units only) D Framework assembly (2 piece) E Mounting
Résumé du contenu de la page N° 7
p eparingr for i ns Talla Tion e ectricall p ower S y uppl WARNING • The electrical service to the range hood should be Electrical Specifications installed only by a licensed electrician. It is the owner ’ s responsibility to ensure that the electrical • Observe all governing codes and ordinances during connection of this appliance is performed by a qualified planning and installation. Contact your local building electrician. The electrical
Résumé du contenu de la page N° 8
p eparingr for i ns Talla Tion p anl eht Dtuc w ork i n S oitn alla t Calculating the Maximum Duct Run Length WARNING The maximum straight duct length for the hood is 100 • T o reduce the risk of fire and to properly exhaust feet. For each elbow and transition added to the duct air , be sure to duct air outside the house or building. work, a certain number of feet must be subtracted from Do not vent exhaust air into spaces within wall
Résumé du contenu de la page N° 9
i ns Talla Toin i ns Tru CTnios a SSme Bel teh h oo D WARNING • Do not install the range hood unless the electrical WARNING service provided meets the range hood specifications. • Lifting and hanging the range hood requires two • Observe all governing codes and ordinances during people. Do not attempt to lift the hood without planning and installation. Contact your local building assistance. department for further information. 1. Place th
Résumé du contenu de la page N° 10
i sn Tllaa Tnoi i sn Tru CTsnio h oo D a SSme B y l (tnoc ) 6. Separate the bottom framework piece from the top 9. Attach the hood junction box to the rim of the bottom framework piece. The top frame work piece has 5-inch framework piece using two machine screws as shown. slots on the the sides. The bottom piece has a series of holes on the sides. 7. Position the bottom framework piece on top of the hood. Slide the studs on the
Résumé du contenu de la page N° 11
i sn Talla Tnoi i sn Tur CTions 1 1. Determine the required framework height . T o deter- CHIMNEY mine the requir ed framework height: • Measure the distance from the ceiling to the cooktop. • Subtract the height at which the hood will be mounted (30” minimum) and the hood thickness (12 1/2”) from the distance measured. 12. Put the top framework piece over the bottom framework piece. The mounting slots on the top piece must be up. 13. U
Résumé du contenu de la page N° 12
i ns Talla Toin i ns Tru CTosni h na Gin G teh r an Ge h oo D i n S all t teh Duct w okr WARNING WARNING • T o prevent personal injury , do not rely on the • Do not use screws to attach the duct work to the mounting springs to hold the hood assembly in place hood exhaust outlet. Use duct tape only . Screws may on the ceiling. Once the hood is hooked in place prevent the damper flaps on the top of the hood from IMMEDIA TEL Y secure
Résumé du contenu de la page N° 13
i ns Taall Tion i sn Tru CTions f nlai e eltcrical i n S ntio lala t f nlai c yhenmi a SSme B y l IMPORTANT: Be careful not to pinch the electrical wires WARNINGS while assembling the chimne y . • T o avoid electrical shock or fire hazard, make sure 1. Move the chimney up toward the ceiling. Line up the the power supply at the fuse or junction box is turned holes on the side of the chimney , above the vents, with of f before proceeding
Résumé du contenu de la page N° 14
i ns Taall Toin i ns Tru CTsion Vniyfire G p eporr o tion pear i n S tion alla t c hilkce St 1. T urn on power at the junction or fuse box. WARNING 2. If the control panel is not lit, remove the filter(s) and • T o ensure a safe and proper installation, the following turn on the main power switch located behind the filters checklist should be complete d by the installer to on the undersid e of the hood . Replace the filter(s). ensure t
Résumé du contenu de la page N° 15
Résumé du contenu de la page N° 16
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
