Résumé du contenu de la page N° 1
EVCK4 Cylinder Extractors
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Résumé du contenu de la page N° 2
Important The manufacturer cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that the manufacturer reserves the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowle
Résumé du contenu de la page N° 3
Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. Control Panel A – Light button B, C, D – Speed level buttons E – Power off button F – Timer button To switch the extractor light on or off • Press button A. To switch on the extractor or to change the speed at any time when the extractor is running • Press button B, C or D for the first, second or third
Résumé du contenu de la page N° 4
Care and Maintenance IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean your extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Cleaning the grease filter Fig. 2 The grease filter
Résumé du contenu de la page N° 5
Changing the Light IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT. Open the base of the extractor as described above and then press downwards on the light housing as shown in figure 5 before removing the bulb. Refit the new bulb taking care not to touch the glass (Fingerprints will lead to premature failure
Résumé du contenu de la page N° 6
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. DOUBLE POLE SWITCHED The wires in the mains lead of this appliance are coloured in accordance with the FUSED SPUR OUTLET following
Résumé du contenu de la page N° 7
Installation IMPORTANT: The extractor is intended to be mounted directly to the ceiling using fixings appropriate for the ceiling. Ensure that there is adequate ceiling strength and supports at the fixing points; if in doubt, consult a joiner or electrician. Your extractor can be used to filter and recycle the air within your kitchen (A), or to extract the air outside (B). When extracting air to the outside, the unit can be vented as shown in the diagram below. Note that we recommend the
Résumé du contenu de la page N° 8
Mounting your extractor 1. Using the supplied template, mark the positions of the 3 main fixing holes and the additional fixing hole (X) on the ceiling. 2. Drill and plug the holes, as required. If screwing directly to the ceiling joists, plugs may not be required (See Important note above) 3. Insert 3 screws into the main fixings, leaving approximately 3mm protruding, as shown in Fig 8. 4. Fit the upper support section (B) into position on the 3 screws and rotate it into po
Résumé du contenu de la page N° 9
Mounting your extractor 6. When used with a CDA hob, the extractor is required to be 650mm above the hotplates. Measure the height of the ceiling and then the hotplate height from the floor. The length of the support sections should be calculated as follows: - Length of support = Ceiling height – (149 + 650 + Hotplate height) Note that if the exact height cannot be set, use the frame position corresponding to the next highest one. 7. Fit the lower section (B) to the upper section (
Résumé du contenu de la page N° 10
Mounting your extractor 9. Assemble the ventilation duct(H), as shown in the diagrams below dependanyt on whether you are extracting air to the outside (Fig 12) or re-circulating (Fig 13), in which case you will need to purchase an optional accessory T-piece(M) from CDA. Ensure that the duct adapter (F) is securely connected to the duct pipe or T-piece in order to minimise noise. 10. Separate the two decorative sections and mount the Fig. 12 upper section(Y) into position, t
Résumé du contenu de la page N° 11
Mounting your extractor IMPORTANT NOTE: The extractor is now mounted and secured to the wall; the electrical connections are now required to be made in order for the extractor to function. 1. Ensure that there are no trapped wires - The mains lead and control wires are easily trapped when securing the stainless section to the motor. 2. Locate the main terminal box (on the left as you look at it) and remove the 2 screws, shown as D on the diagram below. Connect the main connector p
Résumé du contenu de la page N° 12
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
