Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
Table of contents General information ...................................................................................... 27 Recording without automatic switch-off ................................................... 27 AIntroduction .................................... 2 Recording with automatic switch-off (OTR One-Touch-Recording) . 28 Dear Philips customer, .................................................................................... 2 Preventing accidental erasing of cassettes .....
Résumé du contenu de la page N° 3
Résumé du contenu de la page N° 4
The remote control MONITOR TV monitor: To switch between TV reception and VCR playback CHILD LOCK Child lock: To switch child lock on/off SELECT Select: Selecting functions STANDBY/ONm Switch on or off: To switch set on or off, interrupt menu function, interrupt a programmed recording (TIMER) 0-9 Number buttons:0 - 9 TV To call up additional TV functions: Additional TV functions for TV sets with the same remote control code (RC5) TURBO TIMER TurboTimer: To programme a recording with the function
Résumé du contenu de la page N° 5
Additional TV functions Hold down TV and select the corresponding function using the following buttons. STANDBY/ONm Standby : To switch off the TV MUTE y TV sound off: To switch the sound on or off AV To switch the TV to Audio/Video in-socket P ;q Select: To select a programme number P =r Select: To select a programme number QSr TV volume: TV volume down SqP TV volume: TV volume up Front of the device STANDBY/ONm/I Switch on or off: To switch off or on, interrupt a function, interrupt a programm
Résumé du contenu de la page N° 6
The symbols on your video recorder display These symbols can light up on your video recorder display: This is where the current operating mode is shown as a symbol. LP When you have switched on the LP (Long Play) function or when you play a tape that has been recorded in LP (Long Play). When you have switched on the child lock. DEC When a decoder has been allocated to the TV channel (currently selected programme number on the video recorder) you have currently selected on the video recorder. Whe
Résumé du contenu de la page N° 7
Résumé du contenu de la page N° 8
AIntroduction Dear Philips customer, Instruction manuals are usually very dry since they are technically-oriented and often poorly translated. I have been employed by Philips for this reason. Allow me to introduce myself. My name is Phil. I will be guiding you through the instruction manual and try to be of help in operating your new device. At appropriate points along the way, I will be providing you with the following information: Excuse me? Tip Problem For experts Here I will be Here I will b
Résumé du contenu de la page N° 9
Welcome to the large family of owners of PHILIPS VHS video recorders. Thank you for buying a VR170/07 . Please take the time to read this operating manual before using your video recorder. It contains important information and notes regarding operation. The video recorder should not be turned on immediately after transportation from a cold to a hot area or vice versa, or in conditions of extreme humidity. Wait at least three hours after transporting the device. The video recorder needs this time
Résumé du contenu de la page N° 10
Important notes regarding operation Danger: High voltage! Do not remove the top cover as there is a risk of an electrical shock! The video recorder does not contain any components that can be repaired by the customer. Please leave all maintenance work for qualified personnel. As soon as the video recorder is connected to the power supply, there are some components that are in constant operation. To switch off the video recorder completely you must disconnect it from the power supply. These opera
Résumé du contenu de la page N° 11
Special functions of your new video recorder Your PHILIPS video recorder is not just for recording and playing back VHS cassettes. It also has a whole range of special functions which will make the day-to-day use of your new video recorder much easier. Philips has developed a system which produces the best possible playback quality. For old and often-used video cassettes, this system reduces interference. For new or high quality cassettes, it emphasises the details. When you connect your video r
Résumé du contenu de la page N° 12
Important information for customers in Great Britain This set is fitted with an approved moulded 13 amp plug. To change the fuse in this plug or to attach a different plug, please proceed as follows: 1 Take off the fuse cover and remove the old fuse. 2 Insert a new fuse. Suitable fuses are those of the type BS 1362 3A, A.S.T.A. standard or BSI standard. 3 Close the fuse cover. If the attached plug does not meet your requirements, you can cut it off and replace it with a suitable plug. Please obs
Résumé du contenu de la page N° 13
BConnecting the video recorder Preparing the remote control for operation The remote control and its batteries are packed separately in the original video recorder packaging. You must install the batteries in the remote control before use - described in the following section. 1 Take the remote control and the enclosed batteries (2 batteries). 2 Open the remote control's battery compartment and place the batteries in it as shown in the picture and close the battery compartment. The remote control
Résumé du contenu de la page N° 14
Connecting with a scart cable Have the following cables ready: an aerial cable (1, supplied), a mains cable (2, supplied), a scart cable (3). 1 Remove the aerial cable plug from your TV set. Insert it into the socket 2 at the back of the video recorder. 2 Insert one end of the supplied aerial cable into the socket 3 at the back of the video recorder and the other end into the aerial input socket at the back of the TV set. 3 Plug one end of a scart cable into the scart socket EXT.1 AV 1 at the ba
Résumé du contenu de la page N° 15
aMy screen is empty CONGRATULATIONS b Many TV sets are switched to the programme number for the scart socket YOU NOW OWN A NEW PHILIPS by way of a control signal sent through the scart cable. VIDEO RECORDER b If the TV set does not automatically switch to the scart socket programme number, manually change to the corresponding programme number on your TV set (see your TV's operating instructions). CONTINUEpOK Then, read the paragraph 'Initial installation' in the chapter 'Installing your video re
Résumé du contenu de la page N° 16
6 Select this programme number and manually start the TV's channel search as if you wanted to save a new TV channel until the 'test image' appears. aI do not see a test screen' CONGRATULATIONS b Check the cable connections. YOU NOW OWN A NEW PHILIPS b The video recorder 'transmits' on the 583MHz frequency (channel 35) VIDEO RECORDER Repeat the channel search on your TV set. CONTINUEpOK 7 Save this programme number setting on your TV set for video recorder operation. Programme number for video re
Résumé du contenu de la page N° 17
CInstalling your video recording Initial installation This chapter shows you how to start the initial installation. The video recorder automatically seeks out and stores all available TV channels. 'Aim' correctly In the following sections, you require the remote control for the first time. When using, always aim the front of the remote control at the video recorder and not at the TV set. Connecting additional devices After you have connected additional devices (satellite receiver, etc.) through
Résumé du contenu de la page N° 18
Decoder allocation Some TV channels transmit encoded TV signals which can only be viewed with a commercially purchased or hired decoder without disturbances. You can connect such a decoder (descrambler) to this video recorder. The following function will automatically activate the connected decoder for the desired TV channel. 1 Switch the TV on. If applicable, select the programme number for the video recorder operation. 2 Use the buttons P ;q , P =r on the video recorder or the number buttons 0
Résumé du contenu de la page N° 19
Manual TV channel search In some cases it could occur that all of the TV channels were not found and saved during the initial installation. In this case, the missing or coded TV channels must be searched for and stored manually. 1 Switch on the TV set. If required, select the programme number for the video recorder. 2 Press MENU on the remote control. The main menu will appear. 3 Select line 'MANUAL SEARCH' using P =r or P ;q and confirm with OK . 4 Select line 'PROGRAMME NUMBER' using P =r or P
Résumé du contenu de la page N° 20
aI don't know the channels for my TV stations b In this case, press SqP in line 'CHANNEL NUMBER' to start the automatic channel search. A changing channel number will appear on the TV screen. Continue the automatic search until you have found the desired TV channel. 8 Save the TV channel with OK.'STORED' will briefly appear on the TV screen. 9 To search for other TV channels, begin again at step 3 . 0 To end, press MENU . Using the satellite receiver TV channels from a satellite receiver (connec
