Instruction d'utilisation Eureka 3281

Résumé du contenu de la page N° 1

!
!
m
!
a
a
u
k
k
3281 Series
O OW WN NE ER R’’S S G GU UIID DE E
G Gu uíía a d de ell P Pr ro op piie et ta ar riio o
L Le e G Gu uiid de e d du u P Pr ro op pr riié ét ta aiir re e
Before Returning, Call
Eureka Customer Service
Antes de enviar de regreso, Ilame al Servico al Cliente de Eureka
Avant de le retourner, appelez le service à la clientèle Eureka
HELPLINE LÍNEA DE AYUDA LIGNE D’AIDE
1-800-282-2886
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturday -

Résumé du contenu de la page N° 2

Where to Find Important Vacuum Information Keep this information Write the model, type and serial number here: Date of purchase (keep your receipt) _______________ Model number and type _________________________ Serial number _________________________________ Find these numbers on a label on the lower back side of the vacuum cleaner. Refer to these numbers when ordering parts and accessories or if service is needed. Before You Start Your Vacuum Cleaner Refer to Quick Start Guide for assembly a

Résumé du contenu de la page N° 3

ENGLISH IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. ! • Do not allow to be used as a toy. Close attention is necessary wh

Résumé du contenu de la page N° 4

How to Identify Parts of Vacuum Cleaner SPECIAL FEATURES Handle Available on some models Cord retainer Turbo nozzle Power switch Turbo nozzle clip Carrying handle Hose Filter, cover and screen Quick release cord wrap (located inside dust cup) Dust cup Power cord Nested crevice tool Dusting brush Turbo nozzle & extension wand Lower cord wrap HEPA filter compartment Hose retainer Height adjustment knob Handle release Brush roll cover Maintenance Schedule Maintenance Schedule is also located on ba

Résumé du contenu de la page N° 5

ENGLISH How to Use Accessories ! Handle must be in upright position. Raise height adjustment to ‘high carpet’ before using accessories. Replace hose end into hose retainer after using accessories. Crevice Tool and Extension Wand Use for baseboards and corners. Grasp crevice tool and wand near ridges and pull apart. Push crevice tool into wand and place on end of hose. Dusting Brush Use for furniture, drapes and vents. Place dusting brush on end of hose, wand or crevice tool. Bare Floor Nozz

Résumé du contenu de la page N° 6

How to Maintain Your Vacuum Cleaner ! Make sure vacuum cleaner is turned off and power cord is unplugged Maintain Brush Roll Motor can become hot with normal use. Do not remove end caps. Remove hair and threads from brush roll periodically. Check EXT-U Belt. Replace if worn, cut or out of shape ! Avoid touching the motor shaft when checking brush roll or belt. How to replace brush roll or belt 1) Step on handle release to lower handle. Step on release a second time to go to lowest position (Fi

Résumé du contenu de la page N° 7

ENGLISH How to Clear a Blockage Make sure vacuum is turned off and power cord is unplugged. ! Hose Blockage 1) Remove hose from hose retainer. Flexing the hose will loosen any blockage (Fig 1). 2) Base hose – remove 2 screws and brush roll cover. Clear blockage from base hose. Check for debris in brush roll and replace screws and cover (Fig 2). 3) Hose connector – twist hose from connector. Remove blockage and replace hose. (Fig 3). Fig. 1 Fig. 2 Fig. 3 The Eureka Limited Warranty Eureka warr

Résumé du contenu de la page N° 8

Thermal Cut-Off This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off, push the power switch to off (O) and unplug the vacuum. Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum. After the 30 minute period, plug the vacuum back in and turn on the switch. I