Instruction d'utilisation Xantech ML85K

Résumé du contenu de la page N° 1

DESCRIPTION

The Micro Link IR Receiver is a small peep-hole style infrared repeater

assembly. The Micro Link IR Receiver is equipped with a 7-foot cable and a

3.5mm stereo mini plug, which is plugged directly into the “IR RCVR” jack on

the connecting block, such as the models 789-44, CB60, and 791-44. The

Micro Link IR Receiver is primarily intended for use in installations where the

connecting block is within reach of its 7-foot cable – as when installing the

Micro Link

Résumé du contenu de la page N° 2

EMITTERS 789-44 CONNECTING BLOCK ® IR 12VDC RCVR INSTALLATION QUICK-START A typical system will use an IR receiver, several emitters, and a power supply all connected to a connecting block. 1. Connect the IR receiver to the “IR RCVR” port on the connecting block. The ‘red’ connector is installed to the ‘red’ plug. 3.5mm mini plug Signal Name Note: In some extended distances, additional 3-conductor may be required and can be TIP SIGNAL connected to the terminals on the conne

Résumé du contenu de la page N° 3

EMITTERS 791- 44 AMPLIFIE D CONNECTING BLOCK ® HIGH IR IR OUT RCVR 12VDC LARGE SYSTEM APPLICATION 1. The ML85 IR receiver is compatible with all Xantech Connecting Blocks. Micro-Link (ML) IR Receiver Kit Different connecting blocks are provided for application specific situations. For instance, in the diagram below, an optional 791-44 connecting block is used DESCRIPTION to control several components. The ML Series Kit comes with everything needed for a complete IR repeater syst

Résumé du contenu de la page N° 4

STEP 3: Plug in the 283D Designer Emitters 3.5mm mono mini plug (ITEM C) into the ITEM C: (4) 283D Designer Emitters jacks labeled EMITTERS on the 789-44 (ITEM B) and affix the opposite end to the IR Sensor Window of the controlled equipment. Extra double sided adhesive tape is included. The YELLOW connector connects to the YELLOW receptacle. ITEM D: (1) 781ERGPS Power Supply STEP 1: Plug in the 2.1mm Coaxial power plug of the 781ERGPS Power Supply (ITEM

Résumé du contenu de la page N° 5

Symptom #2: TB LED on IR Receiver (and/or Emitters) Dimly lit or IR Troubleshooting Guide flickering Cause: Solution NOTE: Due to the many variables in a given installation, the Signal and ground wires are troubleshooting countermeasures you will have to take may vary from job 1. reversed or shorted either at the Recheck your wiring. to job. Each installation is different due to the number of IR receivers in connecting block or IR receiver. use, length of wire runs, type

Résumé du contenu de la page N° 6

Symptom #3: TB LED on IR Receiver (and/or Emitters) on solid Symptom #4: TB LED on IR Rec. blinks but 283D or 286D 'Blink' style Emitters do not Cause: Solution Cause: Solution Use a 85 or 95 series Plasma 'Friendly' There may be a short, such as a Receiver. If already using a this unit, please staple driven through the Signal 1. Recheck your wiring. note the Plasma interference can be reflected and GND wires of the IR off of any item it comes into contact with within Re

Résumé du contenu de la page N° 7

Symptom 6: Emitters function but some (or all) components do not respond. Symptom #7: Absolutely No Functionality (How to determine which component is at fault) Cause: Solution Component to Test Instructions Reposition the Emitter so that it is directly With a Multimeter, measure the DC Voltage of the over the components sensor window. 1. Emitter placement is incorrect. supply while it is connected to the Connecting Block. Consult the components owners’ manual of Put the Ne

Résumé du contenu de la page N° 8

Limited Warranty Xantech® warrants its products to be free of defects in materials or workmanship. This is a Limited Lifetime warranty from the date of purchase by the original consumer. Any products returned to Xantech and found to be defective by Xantech within the warranty period will be repaired or replaced, at Xantech’s option, at no charge. Xantech will not be responsible for the actual cost of installation or removal of the product, nor for any incidental or consequential damage