Résumé du contenu de la page N° 1
INSTALLATION & USER GUIDE
For Receiving and Routing
Infrared Commands from Any
Remote Control to Concealed
Audio/Video Equipment
IR-KIT
PLASMA PROOF IR REPEATER KIT
Résumé du contenu de la page N° 2
IR-KIT PLASMA PROOF IR REPEATER KIT TABLE OF CONTENTS Features............................................................................................................................1 Product Overview...........................................................................................................2 Package Contents ..........................................................................................................4 Preparing for Installation....................................
Résumé du contenu de la page N° 3
FEATURES n Wings allow for either vertical Installation friendly design: of horizontal mounting n 10' of connecting wire included IR-CB2 n Includes in-line UL listed n Reliable adhesive backing n Provides two IR Receiver regulated power supply inputs and five IR Emitter outputs IR-E1 Infrared Emitter IR-SMR Surface Mount IR Receiver n Infrared pass through housing n Selectable high/low emitter n Plasma-proof design outputs for use with IR-E1HO n Miniature size and shape high output emitter or
Résumé du contenu de la page N° 4
PRODUCT OVERVIEW 2 3 4 1 IR-CB2 6 5 7 IR Blocking Self-adhesive tape Cover Infrared LED 3.5mm mono Infrared mini-plug Transparent Housing 10 feet of 2-conductor IR-SMR 24-gauge connecting wire IR-E1 2
Résumé du contenu de la page N° 5
1. 12V DC Jack – Provides 12Volt DC power to 6. Emitter Hi/Low switch – Setting these switches to IR-CB2 via a regulated power supply. the appropriate position allows you to connect either a high-output flooding emitter (IR-E1HO) 2. IR Emitter Outputs – 3.5mm jacks provide output for or low-output emitter. There is one Hi/Low switch either single or dual low-level flashers. for emitter port four and one Hi/Low switch for 3. 3-30V AC/DC Status – 3.5mm jack provides emitter port five. system stat
Résumé du contenu de la page N° 6
PACKAGE CONTENTS PREPARING FOR INSTALLATION n IR-CB2 x 1 The IR Receiver cables, emitter cables and the 12V n Snap and Lock Connectors x 2 DC power supply cable must all reach the proposed location of the IR-CB2 Connecting Block. Mark the n In-line power supply x 1 cables with wire labels, describing where the cables n Self-adhesive rubber feet x 4 originate from, rather than where they will terminate. n IR-SMR Receiver x 1 Locate a local un-switched AC outlet to be used to n Adhesive-backed st
Résumé du contenu de la page N° 7
INSTALLATION 10. Locate the IR Connecting Block Snap and Lock Connectors and remove them if they are 1. Select an appropriate location for the IR-CB2. plugged in. 2. Run all the necessary wiring to the IR-CB2. Label 11. Use a small flathead screwdriver or your thumb to the wires for future reference. (White) (Yellow) (Black) raise the locking (Red) 3. Plug the supplied 12V DC power supply into the tabs, exposing the un-switched AC outlet. holes on the connectors. 4. Plug the 12V DC power suppl
Résumé du contenu de la page N° 8
INSTALLATION DIAGRAM CD/Audio Player JobSite DVD Player IR-E1 Emitters Cable TV Receiver Satellite Receiver Home Theater Receiver 12V DC Power Supply (Not Supplied) plugged into the Switched Outlet IR-CB2 Optional IR-SMR IR-FMR Receiver Receiver Plasma Display Home Theater In-Wall Speaker Zone 2 6
Résumé du contenu de la page N° 9
Power Status Note: Using an IR-E1 or IR-E2 Emitter with the Emitter Output Switch set to the HI position, can You can send a Power Status signal to IR-SMR damage the emitter. receiver by connecting a 12V DC power supply from the switched AC power outlet of the preamp/receiver 12-Volt Trigger Output to the status input jack of your IR-CB2. Any 12V DC The JobSite IR-CB2 provides a 12V power supply with a minimum of 100mA current DC output that can be triggered capacity can be used. one of two ways
Résumé du contenu de la page N° 10
OPERATION Additional IR Receivers The IR-Kit includes one surface mount receiver. The Test your IR Repeater system by following three included IR-CB2 Connecting Block will accommodate principal guidelines: a second IR Receiver. JobSite makes a variety of 1. All components can be operated: Test all of your receivers for virtually any application. See your remote controls for all of your equipment. JobSite dealer for more information. 2. Operation is consistent: A good test is to repeatedly step
Résumé du contenu de la page N° 11
TROUBLESHOOTING IR Saturation Bad Connections or Wiring Sometimes the emitter output can saturate the IR receiving window of a component. When this If the connections or wiring are wrong, loose, occurs, the IR command will not be executed. This shorted or open, the system will not operate properly. can occur on an intermittent basis when there is a The symptoms could include: Power LED flickers or Plasma TV in the system. is off, IR Test LED is continuously flickering or on without any remote co
Résumé du contenu de la page N° 12
Optical or Electromagnetic Optical Feedback Loop Interference If you have an IR Receiver in the same room as a Direct sunlight, reflections, neon signs and other emitter, and you have some low-level noise or sources of infrared light or television sets, light interference, an optical feedback loop can occur dimming controls and other sources of which will interfere with proper operation. Symptoms electromagnetic fields can induce noise and can include: poor range, intermittent operation or no in
Résumé du contenu de la page N° 13
SPECIFICATIONS IR-CB2 IR-SMR IR system: IR system: Works with practically all brands of IR remote Works with practically all brands of IR remote controls controls IR receiving (varies by brand of remote control): Connections: 18'-30' range 2 receiver inputs, 5 emitter outputs From 20', 30 degrees off-axis Wiring requirements: Category 5 or better Wiring requirements: Category 5 or better, home runs required Home runs required from each IR receiver Mounting: Mounting: Self-adhesive, surface m
Résumé du contenu de la page N° 14
SPECIFICATIONS (CONTINUED) IR-E1 IR system: Dimensions: Works with practically all brands of IR remote 5/16" wide x 3/16" high x 1/2" deep controls IR Blocking Cover Dimensions IR transmitting: 2" wide x 2" high x 1/4" deep 4' (line of sight) Warranty: 2 year limited Emitters mount directly to the IR window of a component Wiring requirements: 10' of 2-conductor 24-gauge wire with a 3.5mm plug is supplied Use 18-gauge for distances up to 20' and 16-gauge for up to 200' Mounting: Self-adhesive
Résumé du contenu de la page N° 15
JOBSITE warrants its active products (those requiring AC LIMITED WARRANTY or battery power) to the original purchaser to be free of JobSite Systems (“JOBSITE”), a Niles Audio Corporation manufacturing defects in material and workmanship for a company, warrants its passive products (those not requiring period of two years from date of purchase. AC or battery power) to the original purchaser to be free of This Warranty is subject to the following additional manufacturing defects in material and wo
Résumé du contenu de la page N° 16
If the above conditions are met, the purchaser’s sole For the name of the nearest authorized JOBSITE wholesale remedy shall be to return the product to JOBSITE, in which distributor, contact: case JOBSITE will repair or replace, at its sole option, the JobSite Systems defective product without charge for parts or labor. 12331 S.W. 130 Street, Miami, Florida 33186 JOBSITE will return the unit repaired or replaced under warranty by shipping it by its usual shipping method from WWW.JOBSITESYSTEMS.C
Résumé du contenu de la page N° 17
NOTES: 15
Résumé du contenu de la page N° 18
NOTES: 16
Résumé du contenu de la page N° 19
17
Résumé du contenu de la page N° 20
JOBSITE SYSTEMS 12331 S.W. 130 STREET, MIAMI, FLORIDA 33186 P 866.4JB.SITE (866.452.7483) – F 305.238.0185 WWW.JOBSITESYSTEMS.COM © 2005 JobSite Systems. All rights reserved. JobSite, Pure Custom and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio Corporation. All other trademarks are the property of their respective owners. Some JobSite products (or components thereof) are manufactured under one or more U.S. Patents, foreign equivale
