Résumé du contenu de la page N° 1
Universal remote Control
3 a
KH 2156
Universal remote Control
per o ating manual
KOMPERNASS GMBH
BURGSTRASSE 21 ⋅ D-44867 BOCHUM
www.kompernass.com
ID-Nr.: KH2156-08/09-V3
08/2009
Résumé du contenu de la page N° 2
KH 2156
Résumé du contenu de la page N° 3
INDEX PAGE Important safety instructions 2 Device summary 3 Initial use 4 Unpacking the device / checking the package contents 4 Inserting the batteries 4 Operating components 5 LCD display 5 Buttons 6 SETUP - System settings 8 Code Setup (Programming the remote control) 10 Programming by brand code search 10 Programming by manual code input 11 Programming by automatic code search 11 System-Setup 13 Setting the time 13 Setting the date 13 Adjust contrast 14 Background Illumination 14 System
Résumé du contenu de la page N° 4
Universal remote control KH2156 Read the operating instructions carefully before using the de- vice for the first time and preserve this booklet for later refer- ence. Pass this manual on to whoever might acquire the device at a future date. Important safety instructions Proper use Children may only operate the remote control under adult supervision. The universal remote control can replace a maximum of ten remote controls. It can only be used for entertainment elec- tronics with infrared
Résumé du contenu de la page N° 5
Damage to the device • If the device is defective, do not attempt to repair it your- self. In case of damage, contact the manufacturer or the manufacturer's service hotline (see Warranty information). • If liquid escapes from the device or if the device has been otherwise damaged, it must be inspected by the manufac- turer or the manufacturer's service hotline. Contact the manufacturer or the manufacturer's service hotline (see Warranty information). Device summary q LCD display w /ALL OFF
Résumé du contenu de la page N° 6
Initial use Unpacking the device / checking the package contents Important! Keep the plastic packaging well away from small children. There is a risk of suffocation! • Unpack the device and accessories. • Check the package contents - Universal remote control (URC), - Operating instructions, - Manufacturers directory with device code list: - 2 x 1,5 V Batteries, type AAA/LR03 (Micro) • Remove the protective foil from the LCD display q. Note: Transport damage If you notice any transport d
Résumé du contenu de la page N° 7
Note: If no LCD display q is visible check the polarity of the batteries or install new ones. Operating components LCD display The LCD display q is divided into fields. Text field 2! Here is shown the currently selected device, for example DVD, TV VCR etc. Infrared symbol 2@ Every time a button is pressed, with which an infrared signal is to be sent the Infrared symbol illuminates. Code/Time field 2# Here is shown the device code of the relevent selected de- vice or the
Résumé du contenu de la page N° 8
The standard readout of the LCD display q consists of the details for the relevent device, for example, "TV", the initial for the day of the week and the time of day indicator. Buttons Note: All the functions described here can, of course, only be used if they are supported by the device being controlled. /ALL OFF button. w S witch device on/off. hold down for approx. 5 seconds to switch all devices on/off. Device buttons e The device buttons are used to select the device that should be o
Résumé du contenu de la page N° 9
CH +/— buttons u Change the reception channel. MACRO button i MACRO button i followed by a number button o 1-4 activates a previously saved chain of commands. Number buttons o Enter programme and device code numbers. Button for one/two digit programme numbers a For two digit programme numbers (depend- ing on the device type) first press the a button then via the number buttons o enter the programme number. When pressed again the display becomes single digit once more. Teletex
Résumé du contenu de la page N° 10
Record/playback buttons f The playback buttons f control devices such as DVD/CD players and video recorders: Record Start playback Stop Playback/Record/Wind Pause playback Wind forward Rewind Mute switching g Switch sound on/off. VOL+/— buttons h Set volume (Volume). MENU button j Access the menu of the controlled device. OK button k You can confirm a menu selection with the OK button. FAV/EPG button l The FAV/EPG button accesses the electronic pro- gramme guide of the device a
Résumé du contenu de la page N° 11
- 9 -
Résumé du contenu de la page N° 12
Code Setup (Programming the remote control) 3 Programming methods are available for the remote control: Programming by brand code search, by automatic code search and by direct code input (manual). First you should use the brand code search since this method is the fastest way of programming if the manufacturer of your de- vice is itemized in the code list. As second is recommended the direct code input followed by the automatic code search. Programming by brand code search With this method
Résumé du contenu de la page N° 13
9. If most of the buttons function press the OK button k to save the setting. In the LCD display q "OK" appears. Now the mode "BRAND CODE" appears again. 10. If, however, none or only a few of the buttons function select with the or button t the next code and test again as described in step 8. 11. With the EXIT button y you will move one level upwards in the menu. Repeat these operational steps for all devices that you would like to control with the remote control. Programming by manu
Résumé du contenu de la page N° 14
1. Press the device button e for the device that is to be con- trolled (i.e. VCR). 2. Switch the device that is to be controlled with the remote control on. With VCR/DVD/CD devices please insert a tape and/or disc. 3. Hold down the S button r for a little longer than 3 sec- onds. 4. In the LCD display q "CODE SETUP" appears. Press the OK button k. "ENTER CODE" now appears in the LCD display q. Press the or button t until "SEARCH CODE" is shown in the LCD display q. Point the remote co
Résumé du contenu de la page N° 15
System-Setup Setting the time The LCD display q shows you the time of day. You set this as follows: 1. Hold down the S button r for a little longer than 3 seconds. The notice "CODE SETUP" appears. If appox. 15 seconds passes without an entry the device exits the menu and returns to the standard display. 2. With the or button t select "SYSTEM SETUP" and confirm with the OK button k. 3. In the LCD display q "TIME SETUP" appears. Confirm with the OK button k. The LCD display q now shows
Résumé du contenu de la page N° 16
Adjust contrast You can set the display's contrast as follows: 1. Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears. 2. With the or button t select "SYSTEM SETUP" and confirm with the OK button k. 3. With the or button t select "CONTRAST SETUP" and confirm with the OK button k. 4. In the LCD display q the contrast value now blinks which you can set with the or button t. Display readout: 0 = highest contrast: 15 = lowest contrast 5.
Résumé du contenu de la page N° 17
Timer Setup The URC offers 2 timer modes, sleep timer and event timer. Sleep timer 1. Press the device button e for the device that is to be con- trolled (i.e. VCR). 2. Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears. 3. Press the or button t until "TIMER SETUP" is shown. Press the OK button k "TIMER SLEEP" appears in the LCD display q. Confirm the selection of this function with the OK button k. 4. Now, below to the right in the LCD display
Résumé du contenu de la page N° 18
Tips: 1. Per timer memory slot a maximum of 14 buttons can be programmed. After entry of the 14th button the sequence will be automatically saved and "FULL" is shown in the LCD display q. 2. In this menu also the device will return to the standard dis- play after approx. 15 seconds without an entry. Learn Setup The Universal remote control (URC) can learn and save but- ton signals of an original remote control. If the URC does not work after applying the programming methods already de- scri
Résumé du contenu de la page N° 19
5. First press the button on the URC that is to be taught. In the LCD display q "LEARNING" appears. The URC now waits for the infrared signal from the original remote control. Note: Should the notice not change to "LEARNING" you have selected a button for which no button code can be taught. 6. Point the infrared sensors 1( of both remote controls towards each other. 7. Now hold down the desired button of the original remote control until "SUCCESS" or "LEARN ERROR" appears in the di
Résumé du contenu de la page N° 20
To programme a Macro For Macro programming proceed as follows: 1. Hold down the S button r for a little longer than 3 sec- onds. The notice "CODE SETUP" appears. 2. With the or button t select "MACRO SETUP" and confirm with the OK button k. In the display "MACRO SETUP 1" appears. 3. With the or button t select the memory slot to be programmed (MACRO SETUP 1 - 4) and confirm with the OK button k. 4. In the LCD display q "MACRO STEP" appears. Now press, one after the other, the desire