Résumé du contenu de la page N° 1
4-117-851-11 (1)
Integrated Remote
Commander
Operating Instructions
RM-VL610
©2008 Sony Corporation
Résumé du contenu de la page N° 2
For the customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, th
Résumé du contenu de la page N° 3
Features The RM-VL610 Remote Commander provides centralized control of all your AV components from a single remote commander and saves the trouble of operating different AV components with different remote control devices. The following are its main features. Centralized control of Sony AV components with this one remote commander This Commander is preset at the factory to operate Sony brand components, so you can use it out of the box as a control center for your Sony AV components. Remote cont
Résumé du contenu de la page N° 4
Startup Guide This guide shows you how to set the Remote Commander to operate your components. First, find the four-digit component code number for your component, referring to the supplied “Component code numbers.” If you have the code If you cannot find the number code number Example: To set up a TV of You can search for the the code number “8011” component code available for your component. 1 Set the Remote 1 Set the Remote Commander for code input mode. Commander for code input mode. Press S
Résumé du contenu de la page N° 5
Learning function If your component does not work as supposed even if the code number is set, make the RM-VL610 “learn” the functions of your component’s remote control. Example: To “teach” the H (play) signal of your video cassette recorder to the VCR H button of the RM-VL610 1 Place the RM-VL610 head to 4 Press the button you head with your VCR’s want to “teach.” remote control. VCR’s remote control 2 – 4 inches (5 – 10 cm) 5 Press and hold the H away (approx.) RM-VL610 (play) button of your V
Résumé du contenu de la page N° 6
Table of Contents Getting Started Installing the Batteries .................................................................................8 When to replace the batteries ............................................................................ 8 Location of Controls .....................................................................................9 Basic Operations Setting the Code for non-Sony Preset Audio and Visual Components — Setting component codes .................................
Résumé du contenu de la page N° 7
Additional Information Precautions .................................................................................................36 Maintenance ...............................................................................................36 Specifications ..............................................................................................36 Troubleshooting ..........................................................................................37 Appendixes Table of Preset Functio
Résumé du contenu de la page N° 8
Getting Started When to replace the Installing the batteries Batteries Batteries for remote control Slide open the battery operation (two size AA (R6) compartment lid and insert two batteries) size AA (R6) batteries (not Under normal conditions, the supplied). Be sure to match up the batteries will last up to 1 year. If + and – indications on the the Commander does not operate batteries with the + and – properly, the batteries might be indications on the battery drained. When this happens, compa
Résumé du contenu de la page N° 9
Location of Controls 1 SET indicator 2 SET button 3 Component Select buttons Light or flash during operation. 4 INPUT button 5 PIP button 6 Number buttons 7 DOT button 8 VOL +/– buttons* 9 MUTING button* q; A, B, C, D button qa LIST button qs FAV button qd GUIDE button qf EXIT button qg Player Control buttons qh SYSTEM CONTROL buttons qj POWER button qk INFO button ql SLEEP button w; ENT (enter) button wa CH (channel) +/– buttons ws RECALL button wd PAGE + button wf PAGE – button wg MENU button
Résumé du contenu de la page N° 10
Basic Operations Setting a component code Setting the Code for non-Sony Preset Audio and Visual Components — Setting component codes The Commander is preset at the factory to operate Sony brand AV components (see the table below). If you are using the Commander with a factory-set Sony components, skip the following procedures. You can use the Commander with other major brand preset AV components also. To use with other AV components, or Sony Example: To set up a Philips’ TV components which do n
Résumé du contenu de la page N° 11
Notes • If you press a component code 3 Press the Component Select number that is not on the table in the button for the desired supplied “Component Code component. Numbers,” or if you press a button in the wrong order, the Component Select button flashes five times, and then turns off. Check the component code number, and try setting it again. • If you don’t input anything into the Commander within 20 seconds The SET indicator and the between each step, the setup selected Component Select proce
Résumé du contenu de la page N° 12
If the Commander does not Setting the Code for non-Sony seem to be working Preset Audio and Visual Try repeating the setup procedure Components — Setting using the other codes listed for your component codes (continued) component, or try setting the code number using the Search function (page 13). Checking if the code Note on the VOL+/– and MUTING number works buttons When you operate a visual 1 Power on the component component, the TV button lights with its power switch. up to indicate that the
Résumé du contenu de la page N° 13
1 Press and while holding Setting a Component SET, press MENU. Code by the Search Function You can find a code number The SET indicator lights up. available for a component that doesn’t have one in the supplied “Component code numbers.” 2 Press the Component Select Before starting the Search button for the desired function component. Set each component to the following status so that the Search function works effectively. TV, AMP: Power-on CD player, MD player*, cassette The SET indicator and th
Résumé du contenu de la page N° 14
Setting a Component Code by the Search Function (continued) Operating Your Components with the 4 Press ENT. Remote Commander When you operate a non-Sony component, make sure you set the component code first (page 10). The SET indicator and the Component button turns off. If the Component Select button flashes five times before turning off, it means that the setup is incomplete. Start over from Step 1. 5 Check if the code number works by following the instructions on page 12. Notes • If you don’t
Résumé du contenu de la page N° 15
2 Press any Player Control To control the volume button. Press VOL +/– to control the volume. Press MUTING to mute See “Table of Preset Functions” the sound. (page 39) for the functions of When you select a visual buttons for each component. component, the TV’s volume will be controlled (TV Component Note Select button lights up), and when The remote control signals may be you select an audio component, different for some components or functions. In this case, program the the amplifier’s volume
Résumé du contenu de la page N° 16
Programming Signals of Another Remote Control — Learning Function To operate components or functions which do not work even if you set a component code number, use the following Learning procedure to “teach” any of the programmable buttons of the Commander to operate the functions of another remote control. You can also use the Learning function to change the signals of individual buttons after setting the component code number (page 10). It is recommended that you make a note of the “learned” k
Résumé du contenu de la page N° 17
2 Press and hold SET for over 4 Press the button on the 3 seconds. Commander you want to “teach.” The SET indicator flash. The SET indicator flashes and the selected Component Select button lights up. (Learning function standby). 3 Press the Component Select button for the component whose signals are to be “learned.” If another signal has already been “learned” by that button The SET indicator flashes twice, and the Commander takes no action returning to its The SET indicator flashes and state a
Résumé du contenu de la page N° 18
Notes Programming Signals of Another • If you do not perform Learning steps Remote Control — Learning within 20 seconds at any point during Function (continued) the process, Learning mode ends. • If you do not perform Step 5 within 10 seconds after Step 4, the learning 5 Press and hold the button procedure returns to Step 3. Repeat Step 4 while the Component Select on the other remote control, button lights. until both the SET indicator and the Component Select To cancel setup, press SET. button
Résumé du contenu de la page N° 19
When you “teach” signals to For accurate Learning VOL +/– or MUTING •Do not move the remote units •If you used the Learning during the Learning procedure. function to program the VOL +/– •Be sure to keep holding down or MUTING buttons to send any the “learning” button until your signal to components other than Commander reacts as described. the TV or AMP, that signal will •Use fresh batteries in both be transmitted only by pressing remote units. VOL +/– or MUTING when you •Avoid Learning in plac
Résumé du contenu de la page N° 20
Programming signals of another 2 Press and hold the remote control — Learning Function (continued) Component Select button for the component whose signals are to be “learned” Programming remote for over 3 seconds. control signals to the Component Select buttons and System Control buttons To teach signals to the SYSTEM CONTROL buttons, press and You can “teach” one operating hold the desired SYSTEM procedure to a Component Select CONTROL button for over 3 button and System Control seconds. button
