Instruction d'utilisation JL Audio Stealthbox SB-GM-TAHOSCNSL/10W3v2

Résumé du contenu de la page N° 1

S SB B- -G GM M- -T TA AH HO OS SC CN NSL SL/ /1 10 0W W3 3v v2 2_ _IIN NS ST TR R_ _S SK KU U# #0 01 11 12 22 20 0

INSTALLATION
If you choose to perform the installation yourself, it is absolutely vital that
DIFFICULT Y:
®
the Stealthbox be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems: OUT
INSTALL ATION GUIDE
OF
for the 1) The sub-bass performance will suffer due to the movement of the enclosure
caused by

Résumé du contenu de la page N° 2

SB SB- -G GM M- -T TA AH HO OS SC CN NSL SL/ /1 10 0W W3 3v v2 2_ _IIN NS ST TR R_ _S SK KU U# #0 01 11 12 22 20 0 STEP 4 STEP 8 Remove the cup holders from center console by pulling Pry the rear face to the rear of the vehicle. upwards. STEP 5 STEP 9 With the cup holders removed, look through the Remove all plugs from the rear face plate. opening and disconnect the exposed wiring harness plug. STEP 6 STEP 10 Pull the wiring harness off the tab. From the back side of the center console, fold

Résumé du contenu de la page N° 3

SB SB- -G GM M- -T TA AH HO OS SC CN NSL SL/ /1 10 0W W3 3v v2 2_ _IIN NS ST TR R_ _S SK KU U# #0 01 11 12 22 20 0 STEP 1 2 STEP 15B Remove the wiring harness that is secured to the passenger The opening with the tabs cut off. side of the center console. STEP 1 3 STEP 16 Remove the pair of screws that are found on each side of the Cut out a pair of 2-inch x 2-inch squares, out of the carpet. center console. Driver side: 4-inches from the driver’s side tape line to the right. If the seat(s) ar

Résumé du contenu de la page N° 4

SB SB- -G GM M- -T TA AH HO OS SC CN NSL SL/ /1 10 0W W3 3v v2 2_ _IIN NS ST TR R_ _S SK KU U# #0 01 11 12 22 20 0 STEP 1 9 STEP 22 ® Once the Stealthbox is in the mounting location, press ® Position the Stealthbox in the mounting location. down on it firmly. ® Remove the Stealthbox carefully, leaving the wax squares in place. The socket cup set screws will leave impressions in the wax. STEP 2 0 STEP 23 The front of the Stealthbox® fits against the black plastic Note: Before drilling, make su

Résumé du contenu de la page N° 5

S SB B- -G GM M- -T TA AH HO OS SC CN NSL SL/ /1 10 0W W3 3v v2 2_ _IIN NS ST TR R_ _S SK KU U# #0 01 11 12 22 20 0 STEP 2 6 INC L UDED H A RD W A RE ® Place the wire harness to the left side of the Stealthbox . ( (2 2) ) 3-i 3-in nc ch h x x 3-i 3-in nc ch h W Wa ax x Sq Squ ua ar re e ( (2) 2) 3 3/ /8 8- -1 16 6 x x 2 2- -1 1/ /4 4- -iin nc ch h Soc Sock ke et t C Cu up p Se Set t Sc Scr re ew w (2) (2) 3 3/ /8- 8-iin nc ch h x x 3 3/ /4 4- -iin nc ch h U US SS S F Flla at t W Wa a