Instruction d'utilisation Woods Equipment BH6500

Instruction d'utilisation pour le dispositif Woods Equipment BH6500

Dispositif: Woods Equipment BH6500
Catégorie: Poignée de poste télé
Fabricant: Woods Equipment
Dimension: 0.68 MB
Date d'addition: 5/14/2013
Nombre des pages: 24
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Woods Equipment BH6500. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Woods Equipment BH6500.

Pour votre confort

Si regarder l'instruction Woods Equipment BH6500 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Woods Equipment BH6500 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Woods Equipment BH6500 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Woods Equipment BH6500 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 24 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Woods Equipment BH6500 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Woods Equipment BH6500. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

59757 Sub-Frame Mounting Kit
Woods Backhoe Model
mounting to
BH6500
Ford/New Holland
Tractor Models
TC18, TC21
Compatible with:
New Holland Loader
7106
or
Woods Loader
1006
MANUAL
PART NUMBER
59756
PN-59756 (Rev. 4/9/01)

Résumé du contenu de la page N° 2

TO THE DEALER: Assembly and proper installation of this product is the responsibility of the WOODS dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration included in this manual. Both dealer and customer must sign the registration which certifies that all Dealer Check List items have been completed

Résumé du contenu de la page N° 3

TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PUMP KIT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 #59757 SUB-FRAME MOUNTING KIT . . . . . . . . . . . . . . . . . . . . . .

Résumé du contenu de la page N° 4

SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! a doctor familiar with this form of injury or gan- Safety is a primary concern in the design and grene, serious injury, or death will result. CON- manufacture of our products. Unfortunately, our TACT A PHYSICIAN IMMEDIATELY IF FLUID efforts to provide safe equipment can be wiped ENTERS SKIN OR EYES. DO NOT DELAY. out by an operator’s single careless act.  Never allow children or untrained persons to In addition to the design and con

Résumé du contenu de la page N° 5

SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! check and comply with these instructions may hoe and use extreme care  Always stand between rear tire and backhoe result in serious injury or death. stabilizer arms or along side of tractor to avoid  Remove seat and upper support assembly being trapped should the boom swing control before installing or removing backhoe from tractor. be accidentally activated. Failure to comply may result in equipment failure  Never leave equipment

Résumé du contenu de la page N° 6

BACKHOE SUB-FRAME INSTALLATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our W ARNING efforts to provide safe equipment can be wiped out by an operator’s single careless act. Only use #59757 Sub-Frame Mounting Kit for In addition to the design and configuration of mounting Woods BH6500 backhoe on Ford/New equipment, hazard control and accident preven- Holland TC18, TC21 tractor models. Sub-Frame tion are dependent upon the awareness, concern, mu

Résumé du contenu de la page N° 7

SUB-FRAME INSTALLATION Cont’d CAUTION  If you do not understand any part of this man- ual and need assistance, see your dealer.  Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head. * Operator’s seat must be located in the lowest and most forward position to obtain 40” minimum radius. Figure 1 Sub-Frame Clearance TRACTOR PREPARATION 3. Disconnect and rem

Résumé du contenu de la page N° 8

SUB-FRAME INSTALLATION Cont’d Install Rear Hanger Brackets 21 22 1. Install new right and left rear hanger brackets (1, 2 2), using eight 10mm bolts (20) and hardened flat washers (22). 20 1 2. Install six 10mm x 1.5P x 80mm (21) and washers 22 (22) to secure rear hangers. 3. Install cap screws (25), washers (29), and nuts 28 (28) through crossmembers welded to rear hanger 29 brackets. 4. Torque 10mm cap screws to 29 lbs-ft. 5. Torque 12mm cap screws to 50 lbs-ft. 29 25 1. 1000578 Right

Résumé du contenu de la page N° 9

SUB-FRAME INSTALLATION Cont’d Install Mid-mount Bracket GREASE FITTINGS 1. Install mid-mount bracket (3) to underside of transmission housing, using cap screws (23) and washers (29) as shown in Figure 4. NOTE: Bracket has a small notch, to be positioned on the left side the the tractor. NOTE: Leave hardware loose. 2. The mounting kit will limit access for two grease fittings on the clutch and brake pedals. Replace 6mm 23 29 straight grease fitting with a 90-degree grease fitting (not supplied

Résumé du contenu de la page N° 10

SUB-FRAME INSTALLATION Cont’d Modify Loader Mounts For tractors equipped with Woods 1006 Loader Loader mounts manufactured prior to April 2001 will NOTE: If rear mount has five slots on each side, pro- need to be modified before reinforcement brackets ceed to next section, Install Right & Left Reinforce- can be installed. Contact Woods Technical Service for ment Brackets. assistance. Install Right & Left Reinforcement Brackets 24 6 For tractors equipped with either New Holland 7106 or Woods 100

Résumé du contenu de la page N° 11

SUB-FRAME INSTALLATION Cont’d Install Crossmember 1. Attach crossmember bracket (4) to right and left reinforcement brackets, using cap screws (24) and washers (29) as shown in Figure 9. 4. 1000581 Crossmember bracket 24 24. 307301 M12–1.75P x 40mm Cap screw 29 29. 57811 1/2 Hardened flat washer, extra thick 4 Figure 9 Crossmember Bracket Installation PN-59756 (Rev. 4/9/01) Installation 9

Résumé du contenu de la page N° 12

SUB-FRAME INSTALLATION Cont’d Sub-Frame Fit-Up 1. Insert sub-frame (1) into rear mounting bracket cradle (2 & 3). 2. Secure with clevis pins (17) and safety pins (19). 3. Pivot sub-frame up and secure to front mount (6) with bent pin (7) and Klik pin (18). 4. Remove sub-frame from tractor. 5. Tighten 12mm hardware to 50 lbs.-ft. IMPORTANT DO NOT install the 3-point hitch top link on this subframe mounting kit. No top link bracket should be used on this backhoe. 6 19 18 17 7 17 19 1 1.

Résumé du contenu de la page N° 13

SUB-FRAME INSTALLATION Cont’d Attaching Sub-Frame to Backhoe 1. With sub-frame removed from tractor, attach to the backhoe using four cap screws (13), six lock washers (14), and six nuts (15). 2. Align step (12) and insert two cap screws (7) through sub-frame holes. Secure with lock washers (6) and nuts (5). 5. 7/8 NC Hex nut 6. 7/8 NC Hex lock nut 7. 7/8 NC x 2-1/2 Cap screw 12. Step 13. 3/4 NC x 2 Cap screw 14. 3/4” Lock washer 15. 3/4 NC Hex nut 15 14 5 6 12 13 7 CD4771A Figure 11 S

Résumé du contenu de la page N° 14

SUB-FRAME INSTALLATION Cont’d Mount Bracket to Pump Kit NOTE: For complete information on pump kit installa- tion, consult the Woods BH6500/7500 backhoe oper- ators manual #37541. The pump mounting bracket is designed to slip over the tractor drawbar and prevent the pump from rotat- ing. 1. Trim the bracket flush with the bottom of the trac- tor drawbar if necessary. 2. Attach pump mounting bracket #59760 (2) to pump assembly as shown in Figure 12. 3. Secure with cap screw (5) and lock nut

Résumé du contenu de la page N° 15

SUB-FRAME & BACKHOE TO TRACTOR Mount Sub-Frame & Backhoe to Tractor DANGER W ARNING W ARNING  The sub-frame mount is designed to provide  Remove seat and upper support assembly secure mounting and adequate operator clear- before installing or removing backhoe from trac- ance when properly installed. Check clearance tor. Failure to comply may result in equipment fail- dimensions shown in figure 1 to be sure you have ure and/or personal injury. installed sub-frame correctly. Follow all mounting

Résumé du contenu de la page N° 16

SUB-FRAME & BACKHOE TO TRACTOR Cont’d 1. Couple the backhoe hydraulic pump to the tractor Connect Hydraulic System PTO. 2. Insert the pump bracket over the tractor drawbar to prevent pump rotation. Engage the pump PTO cou- W ARNING pler pin firmly in the tractor PTO spline groove. 3. Check all hydraulic fittings and lines to be sure  Keep hands and body away from pressurized they are tight and free of kinks or twists. lines. Use paper or cardboard, not hands or other 4. Make sure backhoe PT

Résumé du contenu de la page N° 17

SUB-FRAME & BACKHOE to TRACTOR Cont’d Remove Backhoe With Sub-Frame DANGER W ARNING W ARNING  The only time the backhoe may be operated  Remove seat and upper support assembly from a position other than the operator seat is before installing or removing backhoe from trac- during backhoe attachment and removal. Opera- tor. Failure to comply may result in equipment fail- tor must ure and/or personal injury.  Read Sub-Frame Mounting Kit Manual instructions on attaching and removing back- hoe and

Résumé du contenu de la page N° 18

#59757 SUB-FRAME MOUNTING KIT 30 21 22 15 20 1 2 22 25 29 28 24 6 29 28 29 29 3 29 25 5 28 29 29 24 28 29 29 29 27 29 25 23 33 29 4 32 26 10 31 7 36 35 8 34 16 9 CD5888 Serial Number Plate Located inside sub-frame side rail, rear of cross tube MODELNO. SERIALNO. MASS (KG) ID NO. YR OF MFG. OREGON, IL U.S.A. PN-59756 (Rev. 4/9/01) 16 Parts

Résumé du contenu de la page N° 19

#59757 SUB-FRAME MOUNTING KIT PARTS LIST REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1000578 1 BRACKET-REAR HANGER RT 23 62584 4 HHCS M12-1.75P X 35MM 2 1000579 1 BRACKET-REAR HANGER LT 24 307301 6 HHCS M12-1.75P X 40MM 3 1000590 1 BRACKET-MID MOUNT 25 58515 8 HHCS M12-1.75P X 45MM CL10.9ZP 4 1000581 1 BRACKET-CROSS MEMBER 26 58516 2 HHCS M12-1.75P X 50MM CL10.9ZP 5 1000594 1 BRACKET-REINFORCEMENT RT 27 307302 4 HHCS M12-1.75P X 90MM 6 1000595 1 BRACKET-REINFORCEMENT LT 28 307813 12 NUT

Résumé du contenu de la page N° 20

BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Woods Equipment 1004624 Manuel d'utilisation Poignée de poste télé 1
2 Woods Equipment 1012 Manuel d'utilisation Poignée de poste télé 116
3 Woods Equipment 1009 Manuel d'utilisation Poignée de poste télé 2
4 Woods Equipment 1022120 Manuel d'utilisation Poignée de poste télé 1
5 Woods Equipment 1012606 Manuel d'utilisation Poignée de poste télé 2
6 Woods Equipment 1016 Manuel d'utilisation Poignée de poste télé 7
7 Woods Equipment 1028310 Manuel d'utilisation Poignée de poste télé 0
8 Woods Equipment 2300003 Manuel d'utilisation Poignée de poste télé 0
9 Woods Equipment 2WD Manuel d'utilisation Poignée de poste télé 0
10 Woods Equipment 1013460 Manuel d'utilisation Poignée de poste télé 0
11 Woods Equipment BH9000 Manuel d'utilisation Poignée de poste télé 130
12 Woods Equipment BH6000 Manuel d'utilisation Poignée de poste télé 13
13 Woods Equipment BH7500 Manuel d'utilisation Poignée de poste télé 20
14 Woods Equipment LA852-1 Manuel d'utilisation Poignée de poste télé 0
15 Woods Equipment MAN0063 Manuel d'utilisation Poignée de poste télé 0
16 Sony MB-508/509 Manuel d'utilisation Poignée de poste télé 1
17 Sony MINILUME L5300 Manuel d'utilisation Poignée de poste télé 1
18 Sony MINILUME LF5300 Manuel d'utilisation Poignée de poste télé 1
19 Sony 411 Manuel d'utilisation Poignée de poste télé 15
20 Sony PLP-91/D Manuel d'utilisation Poignée de poste télé 1