Résumé du contenu de la page N° 1
ESPAÑOL FRANÇAIS
ENGLISH
®
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
www.weedeater.com
Instruction Manual
Manual de Instrucciones
245157
Manuel d’Instructions
WE EL-13TNE
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this p
Résumé du contenu de la page N° 2
SAFETYRULES clothing with loosely hanging ties, straps, tassels,etc.Theycanbecaughtinmoving WARNING: Whenusingelectricgar- dening appliances, basic safety precautions parts. S Being fully covered also helps protect you mustalwaysbefollowedtoreducetheriskof fire, electric shock, and seriousinjury. Read from debris and pieces of toxic plants thrownby spinningline. andfollow allinstructions. S Stay Alert. Do not operate unit when you aretired,ill,upsetorunder influence ofal- SAFETY INFORMATION coho
Résumé du contenu de la page N° 3
S Donotabusecord.Nevercarrytheunitby MAINTENANCESAFETY the extension cord or yank extensioncord to disconnect unit. WARNING: Disconnectunitfromthe S Usecordretainertopreventdisconnection power supply before performing mainte- of extension cord from unit and possible nance, or whenchangingtrimmer line. damage to the unit due to plug movement S Maintain unit according to recommended (see ATTACH THE EXTENSION CORD procedures. Keep cutting line at proper TO YOUR TRIMMER in the OPERATION length. Foll
Résumé du contenu de la page N° 4
ASSEMBLY WARNING: If received assembled, WARNING: The upper and lower review all assembly steps to ensure your unit tubes must be snapped together, remain per- is properly assembled and all fasteners are manently assembled together and the locking secure. sleeve assembly must be fully tightened be- fore and during use to avoid serious injury to TUBEASSEMBLY the operator and/or damage to the unit. DO Upper Locking Sleeve Assembly NOT attempt to disassemble unit after initial assembly. Wire protec
Résumé du contenu de la page N° 5
Edge Guide CAUTION: Sharp line limiter blade Holes Bolt Shield 2. Insert the shield onto the motor housing. Ensure the cutting head remains free to rotate and the line is not caught between the shield and the motor housing (see following illustration). 3. Twist the shield as illustrated until the hole in the shield aligns with the hole in the housings. Make sure the shield is assembled to the unit as shown in the following illustration and in the KNOW YOUR UNIT section of this manual. Twi
Résumé du contenu de la page N° 6
AUTOMATIC LINE FEED SYSTEM OPERATING INSTRUCTIONS Use only a voltage supply as specified on When the trimmer is initially started, a small your unit. length of cutting line is fed out. After approximately 5 seconds, the line will SELECT AN EXTENSION CORD be cut to the correct length by the line Extension Cord Gauge Chart limiter as the motor reaches full speed. Make sure the motor is up to full speed Length of Cord Gauge before trimming. 18 Gauge 25 Ft. (7.5 m) If the noise of the cutting
Résumé du contenu de la page N° 7
SCALPING WARNING: Useonly0.065inch(1.65 The scalping technique removes unwanted mm)diameterline.Othersizesoflinewillnotad- vegetation down tothe ground.Holdthebot- vanceproperlyandwillresultinimpropercutting tomofthetrimmerheadabout3inches(8cm) head function or can cause serious injury. Do abovethe ground andat anangle. Allow the not use other materials such as wire, string, tipofthelinetostrikethegroundaroundtrees, rope,etc.Wirecanbreakoffduring cuttingand posts, monuments, etc. This technique
Résumé du contenu de la page N° 8
MAINTENANCE CHECKFORDAMAGEDOR WARNING: Disconnectunitfromthe WORNPARTS power source before performing mainte- Contact an authorized service dealer for re- nance. placementof damagedor wornparts. GENERALRECOMMENDATIONS • Trigger Switch -- Ensure switch functions Thewarrantyonthisunitdoesnotcoveritems properlybypressingandreleasingthetrig- that have been subjected to operator abuse gerswitch.Makesuremotorstops. or negligence. To receive full value from the • Debris Shield -- Discontinue use of uni
Résumé du contenu de la page N° 9
USERREPLACEABLESERVICEPARTS REPLACEMENT PART PART NUMBER Spool with 0.065 ″ Trimmer Line 952711920 Assist Handle 574496301 Bolt Carriage, M6x1 574473201 Knob 574473101 Shield Assembly 574491401 Edge Guide 574491601 Spool cap 574492201 Bolt 574471601 STORAGE • Store unit and extension cord indoors in a high, dry place out of the reach of children. WARNING: Perform the following steps after each use. Store unit unplugged. • Store unit with all guards in place. Position • Stop the unit and disconne
Résumé du contenu de la page N° 10
LIMITEDWARRANTY WEEDEATER, a division of Husqvarna Con- InCanada,contact: sumerOutdoorProductsN.A.,Inc.,warrantsto WEEDEATER theoriginalconsumerpurchaserthateachnew 850MathesonBlvd.West WEEDEATER brand electric or cordless pro- Mississauga,OntarioL5V0B4 duct is free from defects in material andwork- Giving the model number, serial number and manship and agrees torepairorreplaceunder dateofpurchaseofyourproductandthename this warranty any defective WEED EATER and address of the authorized dealer
