Résumé du contenu de la page N° 1
Important Safety Instructions
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electrical
shock, and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a dry cloth for
cleaning.
4. Do not use this product near water; for ex
Résumé du contenu de la page N° 2
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power supply cord is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damag
Résumé du contenu de la page N° 3
Introduction About the EXP900 The EXP900 is a 900 MHz Cordless Phone with voice scramble. It is designed and engineered to exacting standards for reliability, long life, and outstanding performance. Features • 900 MHz operation • Tone/Pulse Dialing • Redial and Flash • One-Way Page, Base Unit to Handset • 10-Number Memory • AutoTalk • AutoStandby • 40 Channels • Battery Saving Feature • Voice Scramble • Handset Volume Control/ • Headset Jack for hands Ringer Volume Control free convenience • Wal
Résumé du contenu de la page N° 4
900M Hz 900M Hz What’s Included with Your EXP900 EXP900 Base EXP900 Handset Belt Clip ® Operating Guide Base Stand Operating Guide AC Power Adapter Lead-Acid Battery Short and Long Telephone Cords If any of these items are missing or damaged, contact your place of purchase. 4 CHARGE IN USE POWER PAGE TALK TALK BATT LOW FLASH CHARGE IN USE MEM VOL CH DE GHI JKL MNO 6 TUV F 1 2 3 4 5 7 PRS 8 9 WXY TONE REDIAL POWER PAGE ABC 0 OPER MUTE VOL CH TALK RINGER 2 ABC 3DEF JKL 6MNO 4 5 7PRS 8 9 WXY 0 1 GH
Résumé du contenu de la page N° 5
Installation Installing Your EXP900 Selecting the Installation Location Select a location for the EXP900 to avoid excessive heat or humidity (as in a kitchen or bathroom). The Base Unit of your EXP900 can be placed on a desk or tabletop near a standard 120V AC outlet and telephone line jack, mounted on a standard AT&T or GTE wall plate, or mounted directly on the wall. Keep the Base Unit and Handset away from sources of electrical noise (motors, fluorescent lighting, etc.). Be sure there is suff
Résumé du contenu de la page N° 6
Setting the TONE/PULSE Switch Place the switch in the TONE position for tone dialing, or the PULSE position for pulse dialing. Installing the Base Unit on a Desk or Tabletop 1. Install the Base Stand on the base. 2. Plug the AC Power Cord (1) and the Telephone Line Cord (2) into the base. 2 1 6
Résumé du contenu de la page N° 7
3. Thread the AC Power Cord through the clip on the base stand, and place the Base Unit on the desk or table top. 4. Raise the antenna on the Base Unit. 5. Plug the other end of the Telephone Line Cord into the telephone wall jack. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Use only the AC Adapter supplied with the EXP900. 7
Résumé du contenu de la page N° 8
6. Route the telephone and power cords where they will not create a trip hazard, or where they could become chafed and create a fire or other electrical hazards. Mounting the Base Unit on a Wall Setting the Handset Retainer 1. Remove the Handset Retainer on the Base Unit by sliding it upward. 2. Flip the Retainer over so the tab is facing up, and slide the Retainer back into the Base Unit. 8
Résumé du contenu de la page N° 9
Mounting on a Standard Wall Plate The EXP900 is designed to be mounted on a standard AT&T or GTE wall plate. 1. Plug the AC Power Cord (1) and the Short Telephone Cord (2) into the base. 2 1 2. Place the power cord in the left molded channel on the bottom of the Base Unit. 3. Plug the short telephone cord into the phone and the GTE Wall Plate jack. Place the Base Unit on the two posts of the wall plate and slide downward to secure. 9
Résumé du contenu de la page N° 10
4. Raise the antenna on the Base Unit. 5. Hang the Handset on the Base Unit. 6. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Use only the AC Adapter supplied with the EXP900. 7. Route the power cord where it will not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards. 10
Résumé du contenu de la page N° 11
Mounting Directly on a Wall If you do not have a standard wall plate, you can mount the EXP900 directly on a wall. Before mounting your cordless telephone, consider the following: • Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. • Make sure the wall material is capable of supporting the weight of the Base Unit and Handset. • Use #10 screws with anchoring devices suitable for the wall
Résumé du contenu de la page N° 12
2 1 3. Place the power cord (1) in the right molded channel and the telephone cord (2) in the left molded channel on the bottom of the Base Unit. 4. Place the Base Unit on the two screws in the wall and slide downward to secure. 5. Raise the antenna on the Base Unit. 6. Hang the Handset on the base unit. 12
Résumé du contenu de la page N° 13
7. Plug the other end of the Telephone Line Cord into the telephone wall jack. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Use only the AC Adapter supplied with the EXP900. 8. Route the telephone and power cords where they will not create a trip hazard, or where they could become chafed and create a fire or other electrical hazards. 13
Résumé du contenu de la page N° 14
Installing the Battery Pack Note: The built-in Memory Backup feature allows up to 3 minutes after disconnecting the old Battery Pack to install a new one without losing any phone numbers that may be stored in the telephone’s memory. Remove the handset battery cover and install the Lead Acid battery. Do not let the battery become fully discharged. Be sure to place the handset in the NOTCH base at night. Always charge a new battery fully before using it. Note: For optimum battery performance, plea
Résumé du contenu de la page N° 15
TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 3 GH I JKL MNO 5 TUV WXY TONE REDIAL TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH 1 2 4 6 7PRS 8 9 0 OPER FLASH Charging the Handset Place the handset on the base to charge. Low Battery Indicator When the Battery Pack in the Handset is low and needs to be charged, the BATT LOW LED flashes every 3 seconds. If this occurs while you are on the phone, you hear an alert tone. C
Résumé du contenu de la page N° 16
Operating Instructions Using the Optional Headset (HS900) 1. Open the black rubber cover. 2. Plug the optional headset into the jack on the left side of the EXP900 handset. 1 2 3 4 5 Note: The earpiece and microphone in your cordless handset are disabled when the headset is plugged in. We suggest you use the Uniden HS900 Headset. This headset is specifically designed to deliver optimum performance. Use of other headsets may result in less than satisfactory performance. 16
Résumé du contenu de la page N° 17
TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH PlacingaCall When the Handset Is on the Base 1. Remove the Handset from the Base Unit and press . 2. The TALK LED will light up. 3. Dial the nu
Résumé du contenu de la page N° 18
TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH 4. When you have finished the call, return the Handset to the Base Unit to hang up. When the Handset Is off the Base 1. Pick up the handset and press . 2. The TALK LED will light up. 18 900M Hz 900M Hz
Résumé du contenu de la page N° 19
TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH 3. Dial the number you are calling. 4. When you have finished the call, press the button to hang up. 19
Résumé du contenu de la page N° 20
TALK BATT LOW MEM VOL CH TALK R.VOL R.TONE ABC DEF 1 2 3 GH I JKL MNO 4 5 6 PRS TUV WXY 7 8 9 OPER 0 TONE REDIAL FLASH Answering a Call When the Handset Is on the Base 1. When the EXP900 rings, remove the handset from the base. 2. The TALK LED will light up, indicating a connection has been made. 3. After you are finished with your conversation, return the handset to the base to hang up. 20 900M Hz
